Godox LED1000D II User manual

LED Video Light
型号:
Instruction Manual
705-LE1B20-00 Made In China
地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋
Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen, China
电话/Tel: [phone](8062) 传真/Fax: [phone]
邮箱/E-mail: http://www.godox.com[email protected]
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
说明手册

一、前言
警 告
感谢您购买神牛产品！
LED1000Ⅱ系列摄影灯灯珠数量多，光线均匀柔和，配置DMX接口，非常适
用于舞台灯光、直播访谈、影棚拍摄、采访布光、静物拍摄以及视频拍摄等。
此灯具有两种型号： LED1000DⅡ白光版(5600K)、LED1000BiⅡ双色温版
(3300K~5600K) ，配备专用遥控器，可无线分组调光，无线调节亮度与色
温，功能丰富，操作便捷。
产品具有以下特点：
请保持干燥:请勿用湿手接触产品,亦不可将产品浸入水中或暴露于雨中。
请勿私自拆卸产品,如产品出现故障须由本公司或授权的维修人员进行
检查维修。
请勿让儿童接触本产品。
本产品不能防水,在雨天及潮湿环境下请注意防水。
请勿放置在超过50度的高温环境中。
请勿在化学品、可燃性气体或其他特殊物质附近使用闪光灯, 这些物质在
特殊情况下可能对闪光灯发出的瞬间强光敏感,有可能导致火灾或电磁干
扰。在这些场合下,请注意相关警告标识。
使用电池的注意事项：
● 切勿将电池投入火中或加热升温。
● 当电量用尽时，电池容易漏液。所以为了避免产品受损，请在长期不使
用本产品或电量用尽时取出电池。
● 如果受损电池中的液体接触到皮肤或衣服，请立即用大量清水冲洗。
1024颗优质灯珠亮度高，照幅广
标配遥控器，无线调节各组亮度或色温
433MHz无线6组16频道分组控制
锂电池或DC供电，拍摄更省心
大液晶屏，参数自动保存
类型
白光版(色温5600K)
双色温版(色温3300K~5600K)
型号
LED1000D II
LED1000Bi II

三、部件
主机
01. 1024粒灯珠
02. 色温片
03. 挡光板
04. ON/OFF开关
05. RUN/STOP按钮
06. 调节旋钮+SET按钮
07. CH/GR按钮
08. Dc电源插座
09. 锂电池插槽
10. 电源指示灯
11. LCD屏(黑底白字)
12. 旋钮A
13. 旋钮B
14. 旋钮C
15. 托架
16. 支架安装孔
17. 电源适配器
18. 电源线
19. DMX In输入口
20. DMX Out输出口
21. DMX512输入接口
22. DMX512输出接口
17 18
电量符号
频道(16个) 组别(6个)
亮度
色温
LCD液晶显示屏
遥控器：
01.LCD屏(白底黑字)
02.电源按钮
03.CH/GR按钮
04.SET按钮
05.下调按钮
06.上调按钮
07.电池槽
08.电池盖
四、电源管理
1. 供电方式
LED1000II摄影灯有2种供电方式
● 锂电池供电
请选择SONY 锂电池BP-L系列电
池(需自行购买)，放置于锂电池插
槽内。
注：
● 使用锂电池供电时，LCD显示当前剩余电量。当电量符号闪烁时，表示
锂电池电量极低。为了防止LED灯自动强行熄灭，请及时对锂电池充电
后再使用。
● 直流电源供电
请选择13~16.8V电源适配器
(标配)，与DC电源插座(08)连接。
01
02 03
06
04
05
无线符号
0201
040608
03 14
15
11
12 13
07
05
16
09
10
19
20 21
22

五、固定摄影灯
● 转动摄影灯的旋钮C(14)至最高点，
将灯架固定在支架安装孔(16)上。
● 扭紧旋钮C(16)。
六、操作说明
1、开关(见图)
● 插入锂电池或者DC电源，按下开关，
电源指示灯点亮，摄影灯开始发光。
● 短按RUN/STOP按钮，控制摄影灯
点亮和关闭。
2、LED普通模式
● 在初始状态下，打开开关进入LED
普通模式(长按RUN/STOP切换LED
普通模式和DMX模式)。
2、安装锂电
● 关闭电源开关(04)。
● 将锂电池带插孔端对准摄影灯锂电池
插槽正负极触点，并推进卡紧。
● 打开电源开关(04)即可。
● 使用完毕，请关闭电源开关(04)。
4、无线远程控制
本产品具备无线遥控功能，使用433MHz无线技术，无视角限制，距离远，
可同时分别控制6个LED灯。16组通道频率，抗干扰强。使用前请把LED
主机和遥控器的频道与组别调至一致。
主机频道/组别调整
● 在常态时，按CH/GR按钮，此时组别闪烁，旋转调节旋钮可选择
组别(A~F)；
● 在常态时，按CH/GR按钮2次，此时频道闪烁，旋转调节旋钮可选择
频道(1~16)；
遥控器频道/组别调整
● 在常态时，按CH/GR按钮，此时组别闪烁，按 "-" "+" 按钮可选择
组别(A~F)；
● 在常态时，按CH/GR按钮2次，此时频道闪烁，按 "-" "+" 按钮可
选择频道(1~16)；
遥控器亮度/色温参数调节
● 在常态时，按 "-" "+" 按钮可对亮度调整；
● 在常态时，按SET按钮1次，此时色温值闪烁，按 "-" "+" 按钮可对
色温调整。
注：主机在开机状态下才可以接收无线信号。
其他操作说明
● 按遥控器的ON/OFF按键，可打开或者关闭所有组别的LED灯。
● 长按遥控器“SET”按钮2秒，可打开或者关闭当前组别的LED灯。
● 遥控器开机后4个小时无操作自动关机。
遥控器使用提示：
(1)使用白光版时，请把遥控器的色温值固定在5600K；
(2)长时间不使用，请取出电池。
3、亮度/色温调节
● 亮度调节：在常态时，旋转主机上的调节
旋钮可调整亮度，亮度调节范围：
0～100%。
● 色温调节：在常态时，短按SET按钮，此
时色温值闪烁，旋转调节旋钮可调整色
温，色温调节范围：3300K～5600K。

八、标配物品
包含物品
LED摄影灯
遥控器
电源适配器
电源线
柔光片
黄色滤色片
蓝色滤色片
序号
1
2
3
4
5
6
7
LED1000D (5600K)
1个
1个
1个
1条
1个
1个
1个
LED1000Bi (3300K~5600K)
1个
1个
1个
1条
1个
无
无
LED摄影灯 遥控器
电源适配器
电源线
5、滤色片更换(见图)
● 用手轻轻捏住色温片(02)向上拉出。
● 将新色温片直接插入，向下推移，色温片
更换完毕。
七、DMX模式
1、选择DMX模式(见图)
● 在初始状态下，按着RUN/STOP按
钮、 打开开关进入DMX模式；此时显
示屏会显示亮度值和色温值(色温值和
亮度值交替显示)。
● 在LED普通模式时，长按
RUN/STOP按钮进入DMX模式，此时
显示屏不显示亮度值和色温值。
2、设置DMX通道号
● 按SET按钮DMX通道号闪烁，旋转
旋钮设置DMX通道号。通道号设置
范围：1-512.
3、连接控制台
● 根据控制型号选择DMX接口。每个灯都占用2个DMX频道，调试频道
分别为亮度/色温。
注：DMX模式时，只能通过控制台设定色温和亮度。

LED灯
锂电池供电
DC电源供电
频道
组别
功率
色温
100%光照度
(LUX) (≈)
CRI(≈)
TLCI(≈)
调光范围
灯珠数量
工作环境温度
产品尺寸
净重
白光版LED1000D II
14.8V锂电池（BP-L接口）(需另购)
13~16.8V
16个
6组（A，B，C，D，E，F）
最大70W
5600K±300K
双色温版LED1000Bi II
遥控器
供电
无线频率
距离(空旷)
频道
分组遥控
待机时间
工作环境温度
产品尺寸
净重
RC-A5 II
3.0V(AAA*2)(不包含)
433MHz
20米
16个
6组(A，B，C，D，E，F)
1年以上
-10~40度
120mm*38mm*15mm
设计和规格如有变更，恕不另行通知。
九、产品参数
5400(1米)
0%~100%
1024个
-10~40度
430*460*100mm
2.51kg
3300K~5600K ±300K
4800 (1米/4200K)
2200 (1米/3300K)
2600 (1米/5600K)
5600K512个
3300K512个
30g
96
98

Foreword
Warning
Thank you for purchasing this Godox product!
This LED1000 II video light is excellent for product shooting, photojournalistic and video
recording, etc. It provides a wide spectrum, beautifully soft and even illumination for
photography. Two models are available: LED1000D II Daylight Version (5600K), and
LED1000Bi II Bicolor Version (3300K~5600K).
Features:
● 1024-LED-bulbs panel is lithium-ion or DC powered
● Wirelessly adjust brightness or color temperature
● Wireless 433MHz grouping system (6 groups & 16 channels)
● Large-sized LCD panel. Settings auto saved.
Type
Daylight Version(Color Temperature 5600K)
Bicolor Version(Color Temperature 3300K~5600K)
Model
LED1000D II
LED1000Bi II
Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product must be sent
to an authorized maintenance center.
Keep out of reach of children.
As this product do not have waterproof function, please take measures of
waterproof in rainy or damp environment.
Do not use or store the product if the ambient temperature reads over 50 °C.
Do not use the flash unit in the presence of flammable gases, chemicals and other
similar materials. In certain circumstance, these materials may be sensitive to the
strong light emitting from this flash unit and fire or electromagnetic interference
may result.
Observe precautions when handling batteries:
● Do not put batteries into a fire or apply direct heat to them.
● Batteries are prone to leakage when fully discharged. To avoid damage to the
product, be sure to remove batteries when the product is not used for a long time
or when batteries run out of charge.
● Should liquid from the batteries come into contact with skin or clothing, rinse
immediately with fresh water.
LED Video Light
Model: Instruction Manual | English

Parts
01. 1024 LED Beads
02. Color Filters
03. Reflector
04. ON/OFF Power Switch
05. RUN/STOP Button
06. Select Dial + SET Button
07. CH/GR Button
08. DC Power Jack
09. Lithium Battery
Compartment
10. Power Indicator
11. LCD Panel (White in Black)
12. Knob A
13. Knob B
14. Knob C
15. Bracket
16. Bracket Mounting Hole
17. Power Adapter
18. Power Cord
19. DMX In
20. DMX Out
21. DMX512 Input Port
22. DMX512 Output Port
Battery
Level Indicator
Channel (16) Controllable
Group (6)
Light
Brightness
Color
Temperature
LCD Panel
Wireless Signal
Remote Control:
01. LCD Panel (Black in
White)
02. Power Switch
03. CH/GR Button
04. SET Button
05. "-" Button
06. "+" Button
07. Battery Compartment
08. Battery Compartment
Cover
Power Management
1. Power Supply
Two power supply modes are available:
● Using lithium battery: This light uses
SONY BP-L model lithium battery
(purchased separately).
Note:
● When using lithium battery, the Battery Level Indicator is displayed on the LCD
panel. When the indicator blinks, the lithium battery power is low. Please recharge it
immediately before usage in order to avoid forceful auto off.
● Using DC power jack: This light can be
powered by DC power supply. Use a
13~16.8V adapter (included) to
connect the light with the DC power
jack (08).
17 18
0201
040608
03 14
151112 13
07
05
16
09
10
19
20 21
22
01
02 03
06
04
05

2. Installing Lithium Battery
● Turn the Power Switch (04) off.
● Target the socket of the lithium battery
towards the "+" "-" contacts of the Battery
Compartment (09). Push the battery in until
it locks.
● Power the light on.
● After using the light, please power it off.
Using the Video Light
● Screw the Knob C (14) to the highest
point and install the light stand onto the
Bracket Mounting Hole (16).
● Tighten the Knob C (14).
Operation
1. Power Supply
● Insert lithium battery or connect the light with
DC power supply. Switch the power on, the
Power Indicator is on and the video light
giving out light.
2. LED General Mode:
● in initial state, power the LED light on to enter LED
general mode (long press the RUN/STOP button
to switch LED general mode and DMX mode).
Color Temperature
5600K
3300K/5600K
3400K~5500K
4. Wireless Remote Control
With 433 MHz wireless system, this product has remote grouping and control function.
Up to 6 groups of LED light can be controlled. 16 channels are available with strong
anti-interference capability.
Please set the channels and groups of LED video light to the same as those of remote
control before usage.
Light Brightness Range
0%~100%
0%~100%
25%~100%
Adjusting Channel/Group of the LED Video Light
● Press the CH/GR button and the group icon blinks. Turn the select dial to choose
a group ID (A to F).
● Press the CH/GR button twice and the channel icon blinks. Turn the select dial to
choose a channel ID (1 to 16).
Adjusting Channel/Group of the Remote Control
● Press the CH/GR button and the group icon blinks. Press the “+” “-” button to choose
a group ID (A to F).
● Press the CH/GR button twice and the channel icon blinks. Press the “+” “-” button to
choose a channel ID (1 to 16).
Adjusting Light Brightness/Color Temperature with the Remote Control
● Press the“+””-“button to adjust the light brightness.
● Press the SET button of the remote control once and the color temperature icon blinks.
Press the “+” “-” button to adjust the color temperature.
Note: The wireless signal can be received only when the LED light is power on.
3. Light Brightness/Color Temperature Adjustment:
● Light Brightness Adjustment: turn the select dial on
the body to adjust light brightness from 0% to 100%.
● Color Temperature Adjustment: short press the SET
button and the color temperature value will be
blinking. Then, turn the select dial to adjust color
temperature from 3300K to 5600K.
Model
LED1000D II
LED1000Bi II

Other Operation Tips:
● Pressing the ON/OFF button on the remote control can turn on/off all the LED groups.
● Pressing the “SET” button on the remote control for 2 seconds can turn on/off the
current LED group.
● The remote control will auto power off after four hours of idle operation.
Tips of Using Remote Control:
(1)When using the Daylight Version LED1000D II, please set the color
temperature of the remote control as 5600K constantly;
(2)Please remove the battery if the light will not be used for an extended period
of time.
5. Replacing A Color Filter
● Pinch the edge of the color filter (02) and pull
it out upwardly.
● Insert a new color filter in and push it
downwardly. Then the color filter is securely
in position.
What’s in the Box of LED1000II?
Included Item
LED Video Light
Remote Control
Power Adapter
Power Cord
Diffusion Filter
Yellow Filter
Blue Filter
NO.
1
2
3
4
5
6
7
LED1000D II
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
LED 1000Bi II
1 PC
1 PC
1 PC
1 PC
1 PC
NO
NO
LED Video Light Remote Control
Power Adapter
Power Cord
DMX Mode
1. Choose DMX Mode
● In the initial state, hold down the RUN/STOP
button and power the light on to enter DMX mode,
and the brightness value and color temperature
value will be displayed on the LCD panel.
● In LED general mode, long press the RUN/STOP
button to enter DMX mode. In this way, the
brightness value and color temperature value won’t
be displayed on the LCD panel.
2. Set DMX Channel
● Press the SET button and the DMX channel will
be blinking. Turn the select dial to set DMX from
1 to 512.
3. Connect to Console
● Choose DMX port according to the model to
be controlled. Each light will occupy two DMX
channels and the light brightness or color temperature can be adjusted.
Note: In DMX mode, the color temperature and light brightness can only be
controlled by the console.

Remote Control
Power Supply
Wireless Frequency
Distance(emptiness)
Channel
Group
Standby Time
Operation Temperature
Dimension
Net weight
RC-A5 II
3.0V(AAA*2)(not include)
433MHz
20m
16
6 groups(A, B, C, D, E, F)
Over one year
-10~40°C
120mm*38mm*15mm
30g
* Product design and specifications are subject to change without notice.
Technical Data
LED1000II
Video Light
Lithium Battery
DC Power Supply
Channel
Group
Power
Color Temperature
Brightness(LUX)
()
CRI ()
TLCI ()
Light Brightness Range
LED Beads Quantity
Operation Temperature
Dimension
Net Weight
Daylight Version
LED1000D II
14.8V Lithium Battery(SONY BP-L model lithium battery)
(sold separately)
13~16.8V
16
6 groups(A,B,C,D,E,F)
Max. 70W
5600K±300K
5400(1m)
96
98
0%~100%
1024
-10~40°C
430*460*100mm
2.51kg
Bicolor Version
LED1000Bi II
3300K~5600K ±300K
4800 (1m/4200K)
2200 (1m/3300K)
2600 (1m/5600K)
5600K: 512
3300K: 512