Gofit Platinum gftms01 User manual

GoFit Platinum Silver Treadmill

GFTMS01

GoFit Platinum Pty Ltd

Phone 1800 446 348 fax 1300 446 348

www.gofit.com.au

IMPORTANT PRECAUTIONS

When using an electrical appliance, the basic following precautions should always be followed:

Read all instructions before using this equipment.

DANGER – To reduce the risk of electric shock:

Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING– To reduce the risk of burns, fire, electric shock, or injury to persons:

1) An appliance should never be left unattended when plugged in.

Unplug from outlet when not in use and before adding or removing parts.

2) Close supervision is necessary when this appliance is used by, or near children and disabled persons.

3) Use this appliance only for its intended use as described in this manual.

Do not use attachments not recommended by the manufacturer.

4) Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged. In this instance, call GoFit Platinum for an inspection.

5) Do not carry this appliance by supply cord or use cord as a handle.

6) Keep the cord away from heated surfaces.

7) Never operate the appliance with the air openings blocked.

Ensure air openings are always free of debris.

8) Never drop or insert any object into any opening.

9) Do not use outdoors.

10) Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

11) To disconnect, turn all controls to the off position, then remove plug from outlet.

12) Do not use this machine with an extension cord, connect direct to grounded outlets only.

13) Ensure at the end of use, elevation is back to the original position.

14) The treadmill must be unfolded during use and only folded again at the end of use with

elevation back to 0.

15) This machine is only intended for domestic use.

Do not use this GoFit Platinum Treadmill in any commercial, rental, or institutional setting.

SAFETY INSTRUCTIONS

Before you start training on your treadmill, please read the instructions carefully.

Follow the steps of the assembly instructions carefully.

Use only the original parts as delivered.

For assembly, use only suitable tools and ask for assistance if necessary.

Because of possible corrosion, the use of any exerciser in moist areas is not recommended.

Keep the GoFit Platinum Treadmill indoors, away from moisture and dust.

Do not put the GoFit Platinum Treadmill in a garage or covered patio, or near water.

Make sure before each use that you have enough space around the treadmill so that you are

clear of potential obstructions ie. walls and surrounding furniture.

Check before the first training session and every 1-2 months to follow that all connecting

elements are tight fitting and in good condition.

WARNING: The safety level of this treadmill can be maintained only if it is examined regularly for

damage and wear, e.g. connection points, power cord, etc.

Replace defective components immediately and keep the equipment out of use until repair.

For repairs, use only original spare parts and when in doubt, ask GoFit Platinum for advice.

Only one person is permitted to use this treadmill at the same time.

Do not use this exerciser while eating, drinking, or smoking.

The maximum load capacity is 120 kg.

Servicing other than the procedures in this manual should be performed by an authorized

service representative only.

Pregnant woman should not use this treadmill unless having consulted and approved by their doctor.

WARNING:

Before beginning any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with

pre-existing health problems. If you feel faint, dizzy or experience any sickness

or pain while using this equipment, cease exercise immediately and consult

your physician. Read all instructions and warnings before using.

GROUNDING INSTRUCTIONS

The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a

path of least resistance for electric current to reduce the risk of electric shock. The product is

equipped with a cord having an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the

products are properly grounded. Do not modify the plug provided with the product – if it will not fit

the outlet, have a proper outlet install by a qualified electrician.

The product is for use on nominal 220 ~ 240 volts

Make sure that the product is connected to an outlet having the same configuration as the plug.

Do not use any adapters or extension cords with this product

BEFORE YOU BEGIN

Thank you for selecting the revolutionary GoFit Silver Treadmill. The GFTMS01 offers an

impressive array of features to make your home workouts more enjoyable and effective.

For your benefit, read this manual carefully before using the GoFit Silver Treadmill.

OVERVIEW

TREADMILL PRE-ASSEMBLY CHECKLIST

- 7 -

ASSEMBLY STEPS

CAUTION!

Please follow the assembly steps below

carefully and exactly to aviod injury .

ALWAYS ASSEMBLE THE TREADMILL

WITH AN ASSISTANT, DO NOT

ATTEMPT ASSEMBLY BY ONESELF.

STEP ONE

Place the two computer handrail tubes of

Frame (A) as shown to the right and

tighten with hex screw.

STEP TWO

Place the left and right uprights as shown

to the right and tighten with hex screw (B)

- 8 -

STEP THREE

After left and right Uprights are

tightened, cap left and right

Decoration Covers (B, C) to the Frame

and tighten them with Phillips Screw

- 9 -

CAUTION

The cylinday contains high pressure gas.

Precautions must be taken to avoid it

crashing into other objects

If the cylinder is hit, it may cause damage

and make the use not smooth. When the

user is folding the treadmill, it may result in

the falling of the frame and cause injury.

This treadmill is foldable.

All operation should be stopped when

folding (include stopping walking belt &

disconnecting power cord)

Pull out the POP-Pin in the folding fixing

mechanism as shown in the diagram then

lift the frame until the POP-Pin inserts into

the frame. On the contrary if you want to

use the treadmill, pull out the POP-Pin of

the folding mechanism as the arrow

shows in the diagram and put down the

frame slowly

•To prevent injury when moving a folded

treadmill, hold on to the adjustment box

with two hands. Then pivot the treadmill

towards you until the wheels of the

treadmill are rolling freely.

•Make sure the floor is cleared and flat

when moving the folded treadmill around.

- 10 -

MAINTENANCE

1. Centering the Walking Belt.

If the Walking Belt tracks off center to the

right or left of the deck, first turn the power off.

Then use a wrench to tighten the rear roller

bolt on the side of the treadmill toward which

the belt is moving. For example, if the belt

moves to the left and the deck becomes

exposed on the right, tighten the bolt on the

left side of the frame. Tighten about 1/4 of

turn (clockwise). If the belt does not move

back to the center of the treadmill, make

another adjustment to the same bolt.

Once the Walking Belt has been adjusted

closer to the center, the treadmill can be

started again.

•Make sure the walking belt is going on

right without any tracks off the centers

2. It is recommended that the deck be

lubricated every 6-12 months according to the

frequency of usage. First, use the wrench to

loosen the bolts and end caps. Pull up the

Walking Belt, dispense the lubricant on the

deck and spread evenly. After lubricating the

deck, center the belt and check the belt

tension. If the belt happens to slip, follow the

above steps and lubricate the running deck.

SUGGESTED PREVENTIVE MAINTENANCE SCHEDULE IN

ACCORDANCE WITH THE AVERAGE RUNNING SPEED

Measurement

Speed

Interval

Metric

6KM/hr

below

1 year

6~12KM/hr

6 months

12KM/hr

above

3 months

English

4mile/hr

below

1 year

4~8mile/hr

6 months

8mile/hr

above

3 months

Note: This preventive maintenance

schedule is only meant for home use.

- 11 -

COMPUTER INSTRUCTION

I. Start Display:

1) If the SAFETY KEY is taken off, the matrix screen will display arrow down.

If the SAFETY KEY is replaced, the matrix screen will display KGS (LBS)

Weight window glitters and displays the pre-set value. The value is 70kg (150LBS) and

range 23~130KG (50~286LBS). At this time the light of Weight window shows.

Finish setting, press ENTER and the window will turn to Start / Ready status.

The matrix window displays a heart-shaped picture. The aim of setting weight is to make a

change of burning CALORIES.

This can be only done after starting. It does not need to be set in PROGRAM. It means you

can use the value after starting. You must reset each time you start.

2) If the SAFETY KEY is removed during work out, the beeper will sound and the treadmill

will stop running. At this time place the SAFETY KEY back and all the values will go back

to the initial position.

3) Under the common Start / Ready status, PULSE window will display HP picture if you

don’t grip the pulse sensor. If you grip the pulse sensor, you will see the PULSE window

starting to display pulse value.

II. Operation Instruction:

1) Under Start/Ready position, you can press Mode directly to enter the program.

2) Under Start/Ready position, press Start to enter directly the start-up of Manu run.

3) If the machine has a fan function, you can press the fan button to start or stop fan.

Pressing once means starting and pressing twice means stopping.

- 12 -

III. Edit Mode:

1) At Start/Ready position, press Mode to choose Manual and Program by press +/- key.

2) Program Mode: Press +/- key to edit the Program (P1~P8), and the PROGRAM

3) window will flash, LCD window will show P1~P8 to edit, you can press +/- key to edit.

Press ENTER to enter the TIME edit, the Program pre-set value is 30min, Range is 20~99min,

STEP is 1min. After edit, press ENTER or START to start the machine.

If you press START directly during edit, the rest un-edited functions are pre-set.

During edit, INCLINE and SPEED window will display first level value.

The matrix window will display the picture.

4) WARM UP and COOL DOWN function: During WARM UP or Program position, change

speed or inclination, the value will increase or decrease in the next level.

COOL DOWN is not affected and STOP is the only function which can be carried out.

5) PROGRAM has 30 levels in all. The three anterior are WARM UP, the three later are COOL

DOWN. Each is 3 minutes. The setting time except anterior and later which mean 6 minutes

will be execute averagely by surplus 24 levels.

6) 9 HOLES mode has no functions of WARM UP or COOL DOWN. When distance is equal

to 3.5KM, the motor will stop, the INCLINE is 0 and displays” End”

** When the SAFETY KEY is taken off and then replaced, it will not revert to original position.

You need to press start key to perform the incline to reposition it.

** Under start/ready status, if you continuously press stop key for 5 seconds, it will reposition.

** During any program, if you press stop key, the program will stop.

If users want to continuously perform the program, press start key or again press stop

key to leave the program and back to start/ready status

IV. Program Operation and Instruction：

1) When you press START, it will begin to count down for 3 seconds, after that, the motor will start,

speed begins at 1 .0KPH (0.6MPH).

2) Speed STEP is 0.1, you can press SPEED UP/DOWN key to select (the speed UP/DOWN

step is 0.1), or press speed instant key 1'2' 4' 6 '8' 10 to select.

3) Incline STEP is 1, you can press INCLINE UP/DOWN key to select (incline UP/DOWN step is

1), or press incline instant key 2 '4 ' 6 ' 8 ' 10 ' 12 to select.

4) SETTING TIME:

- 13 -

•When TIME is set, the window will display the countdown value from target value. When time

reaches 0:00, the treadmill will stop automatically.

•When TIME is not set, the window will display a positive number.

When time reaches 99:00 the treadmill will stop automatically.

5) Pressing Mode key can switch between SPEED, DISTANCE, CALORIES but not INCLINE,

PULSE, WEIGHT. It will just display INCLINE. When there is PULSE signal, it will display

the PULSE value. When there is heartbeat value, the PULSE window will display the heartbeat

value.

6) Press Stop when the motor is working, the motor will stop and the incline motor will stop, the

Time window will display Stop; If you press START key again, the motor will start after

3-seconds countdown, the speed will be kept at the same before stop, and the incline will be

increased to the set height before stop .

7) When it is at stop position, hold the Stop key for 3 seconds, and it will go back to the

Start/Ready position.

8) It will go back to the Start/Ready position after 30 seconds in the End position

(or press Stop Key)

9) The time pre-set value is 0, range is 20~99. When the time is 20 minutes, press +- to

V. Program mode

P1 Manual time: Pre-set value 0min; Range 20~99min; step 1 min

P2 9 hole LEVEL: Initial Value 1; Range1~10; step1; 3500 meter based on distance.

P3 hill climb LEVEL: Initial Value 1; Range 1~1 0; step 1