Gold Metal 8080 Series User manual

© 2015 Gold Medal Products Co. Part No. 88586
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Table Top Steamer Cart
Model No. 8080 Series

Table Top Steamer Cart Model No. 8080 Series
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Table Top Steamer Cart Model No. 8080 Series
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at -800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)

Table Top Steamer Cart Model No. 8080 Series
Page 4
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 0700 Medallion Drive, Cincinnati, OH 4524 USA -(800)-543-0862.
Model Description
The 8080 Series Table Top Steamer Cart is a stationary unit with four rubber feet, designed for
use on a tabletop (the two wheels and push handles for display only). The unit is equipped with a
handle on each end of the cart for transport (DO NOT transport unit while water is hot).
8080NS: Mini Cart/Hot Dog Steamer (Gold Medal graphics) unit is equipped with Model
8080-05 Pan and Lid Kit (see Steam Pan and Lid Kit section for pan/lid
description).
8080NS: Export Mini Cart/Hot Dog Steamer (Gold Medal graphics) unit is equipped with
Model 8080-05 Pan and Lid Kit (see Steam Pan and Lid Kit section for pan/lid
description).
The following Models are the Steamer Cart only (without pans and lids). See Steam Pan and Lid
Kit Options section for the various pan configurations available for purchase separately.
8080-00-110: Mini Cart/Hot Dog Steamer (Gold Medal graphics) without pans or lids.
8080-00-111: Mini Cart/Hot Dog Steamer (Eisenburg graphics) without pans or lids.
8080-00-112: Mini Cart/Hot Dog Steamer (Vienna graphics) without pans or lids.
Items Included with this Unit
Thermometer
Plastic Tongs and Holder
Umbrella
E tension Tube with Bushing

Table Top Steamer Cart Model No. 8080 Series
Page 5
gmpopcorn.com
Setup
This unit has been tested at the factory.
. Remove all packing material and tape before starting operation.
2. After unpacking the unit, rotate the display handles from the shipping position to the
display (UP) position. Remove the two thumb screws holding each handle. Rotate the
handle into the display position and refasten with the thumb screws.
Note: The Display Handles are for display purposes only. Transport handles are
provided for carrying the unit (see image below).
3. Insert the Pans and Lids for use (some pan configurations use a steam pan crossbar).
4. Insert Umbrella (without a handle) into the Extension Tube end with the bushing.
5. Slide the extension tube with the umbrella down into the Umbrella Mount. (The
Umbrella Mount is factory installed using two Thumb Screws, ensure Thumb Screws
are fully tightened for use.)
To remove the Umbrella and Extension Tube, slide the Extension Tube out of the
Umbrella Mount (the Umbrella Mount can stay attached to the unit for future use).
E tension
Tube
Umbrella
(WITHOUT handle)
Bushing
Attach Umbrella
Mount
E tension
Tube to Unit
E tension
Tube
Umbrella Mount
(mounted to unit
with thumb screws)
Thumb Screws
(fully insert thumb
screws to secure)
Transport Handles
(one handle on each
end of unit)
Display Handles
(shown in UP position)
Display Handle
(shown in shipping
position)

Table Top Steamer Cart Model No. 8080 Series
Page 6
gmpopcorn.com
6. To open the umbrella for use, pull down on the umbrella guide and twist slightly. As
the umbrella is released, it will open (reference image shown).
Pull down on umbrella
guide, then twist slightly
to open.
Umbrella Guide
(pull down on
guide to close)
To OPEN
To CLOSE

Table Top Steamer Cart Model No. 8080 Series
Page 7
gmpopcorn.com
Electrical Requirements
The following power supply must be provided:
8080NS, 8080-00-110 (111, 112): 20 V~, 200 W, 60 Hz
8080NSX: 230 V~, 200 W, 50 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Table Top Steamer Cart Model No. 8080 Series
Page 8
gmpopcorn.com
Steamer Pan and Lid Kit Options
Model Series 8080-00 is a base Model Tabletop Steamer Cart only - Pan and Lid Kit must be
purchased separately. Model 8080NS (8080NSX) includes Pan and Lid Kit (Item No. 8080-05) as
standard (shipped with the unit).
Reference the Pan and Lid Kit options below, available for purchase separately.
Option 1 (Item No. 8080
-
01)
( ) /2 Pan, Dome Lid w/Handle
(2) /4 Pans, Flat Slotted Lid
( ) Crossbar
Option 2 (Item No. 8080
-
02)
(3) /3 Pans, w/Flat Slotted Lids
Option 3 (Item No. 8080
-
03)
(2) /2 Pans, Full Hinged Dome Lid
( ) Perforated Insert (for Buns)
Option 4 (Item No. 8080
-
04)
(3) /3 Pans, w/Hinged Flat Lids
Lids have Plastic Knobs
Option 5 (Item No. 8080
-
05)
(2) /3 Pans, Solid Lids
(2) /6 Pans, Solid Lids

Table Top Steamer Cart Model No. 8080 Series
Page 9
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
INICATOR LIGHT
Light ON indicates the power is ON, and the thermostat is calling for heat.
HEAT CONTROL
Turn the Heat Control Knob to adjust the temperature of the steamer. A temperature scale
is located on the knob to indicate the set point temperature.
Operating Instructions
. Remove steamer pans/lids.
2. Pour distilled water into the bottom of the heating compartment – to a height of
approximately 3/4” (about 3 quarts or 2.8 liters).
3. Re-install pans/lids (water should just touch the bottom of the insert pans.)
4. Preheat on high for about 30 minutes (when starting with a room temperature unit).
5. Place food product in the pans and allow them to heat on high until internal
temperature is at least 50°F.
6. Adjust the temperature setting to hold the product at a 50°F serving temperature.
7. Keep the lids in place to help maintain the temperature.
8. When finished operating, turn machine OFF, unplug the unit, and allow water to cool,
then empty the heating compartment by removing pans and carefully dumping water.
DO NOT drain unit while water is hot.
Indicator Light
Heat Control

Table Top Steamer Cart Model No. 8080 Series
Page 10
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
025_020314
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Follow the directions below to clean and sanitize the unit each day after use.
. With the machine OFF, unplug the unit and allow it to cool before attempting to empty
the steamer or clean. DO NOT move or drain unit while water is hot.
2. Do not leave water in the pans overnight.
3. Make sure to clean all of the pans (racks) in order to sanitize them before each use.
4. Clean the outside of the unit with a soft cloth, dampened with soap and hot water.
5. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.

Table Top Steamer Cart Model No. 8080 Series
Page 11
gmpopcorn.com
Troubleshooting
Issue
Possible Cause
Solution
Condensation on Outside
of Unit
A.
Cool Air
A.
Cool air striking the warm steamer may
cause moisture accumulation. Protect the
unit against cool drafts of air.
Hot Dog Casings Burst
A.
Too Much Steam
A.
Too much steam is being generated. Move
the thermostat control to a lower setting.
Buns are Soggy / Buns are
Dry
A.
Too much, or too little
steam
A.
Too
much, or too little steam will produce
these conditions. Control the amount of
steam by adjusting the temperature control,
as necessary. Some buns are better adapted
for steaming than others. Experiment with
different kinds/brands of buns until you find
the one best suited for your application.

Table Top Steamer Cart Model No. 8080 Series
Page 12
gmpopcorn.com
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Table Top Steamer Cart Model No. 8080 Series
Page 13
gmpopcorn.com
ORDERING SPARE PARTS
. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
0700 Medallion Drive
Cincinnati, Ohio 4524 -4807
Or, place orders by phone or online:
Phone: [phone]
(5 3) 769-7676
Fax: [phone]
(5 3) 769-8500
E-mail: [email protected]
Web Page: gmpopcorn.com

Table Top Steamer Cart Model No. 8080 Series
Page 14
gmpopcorn.com
Cabinet Exterior – Parts Breakdown
Item Part Description
Part Number
8080NS,
8080-00-110
(111, 112)
8080NSX
HANDLEGRIP FOR "OD BLACK
88547
88547
2
HANDLE TUBE " O.D.
88546
88546
3
/4
-
20 X /2 THUMB SCR
88567
88567
4
HANDLE PLUG
88935
88935
5
UMBRELLA MOUNT
. 25"O.D.
88545
88545
6
WATER PAN WELD ASSY
88543
88543
7
RUBBER FEET CASE BOTTOM
4 282
4 282
8
CASE BOTTOM COVER ASSY (feet included)
88553
88553
9
WHEEL 7 X /2 X .374B
88548
88548
0
5/ 6
-
8 X 2 /4 HEX HD ZP
88552
88552
KNOB, HEAT
CONTROL
87049
87049
2
STRAIN RELIEF #SR
-
6P3
-
4
76026
76026
3
LEAD
-
IN CORD 5 AMP PLUG
22038
POWER SUPPLY CORD, EXPORT
42369
4
PILOT LIGHT
4 469
4 466
5
DRAWER HANDLE
87420
87420
1
*
CAUTION: If supply cord is damaged, it must be replaced
by Gold Medal Products Co., its service agent, or
similarly qualified persons in order to avoid a hazard.
2
3 5
12
13*
7
9
15
14
11
6
8
10
4
Model 8080NS shown

Table Top Steamer Cart Model No. 8080 Series
Page 15
gmpopcorn.com
Cabinet Exterior – Parts Breakdown
Item Part Description
Part Number
8080NS,
8080-00-110 (111, 112)
8080NSX
ELEMENT RETAINER
88539
88539
2
WIRE ENCLOSURE BOX
88560
88560
3
STRAIN RELIEF T&B #3302
89045
89045
4
TRANSFER PLATE
88540
88540
5
ADJ THERMOSTAT 275F
69054
69054
6
THERMOSTAT 400F BAKERS
76054
76054
7
THERMOSTAT COVER
87306
87306
8
HEAT ELEMENT 200W
88549
88549EX
9
STANDOFF # 0
-
24 X #8
-
32
88544
88544
0
SPACER . 80"ID X .030"LG
88594
88594
INSULATION MAT
W/SLITS
8856
8856
11
9, 10
1
4
5
6
8
2
3
7
Model 8080NS shown

Table Top Steamer Cart Model No. 8080 Series
Page 16
gmpopcorn.com
Pan and Lid Kit Options – Parts Breakdown
1
Model 8080
-
01
2
3
4 5
Model 8080
-
02
6
7
Model 8080
-
03
1
Model 8080
-
04
10
11
8 9
Model 8080
-
05
2
14
12
13
6

Table Top Steamer Cart Model No. 8080 Series
Page 17
gmpopcorn.com
Pan and Lid Kit Options – Parts List
Item Part Description Part Number
8080-01 8080-02 8080-03 8080-04 8080-05
/2 X 6 STEAM PAN
39746
39746
2
STEAMER PAN CROSSBAR
88565
88565
3
/4 X 6 STEAM PAN
88896
4
/4 PAN LID NOTCHED
88573
5
/2 SIZE DOME LID
88898
6
/3 X 6 STEAM TABLE PAN
39745
39745
7
/3 PAN LID NOTCHED
88572
8
HINGED DOME LID FULL
69675
9
/2 SIZE PERF BOTTOM
69676
0
/3 X 6 STEAM PAN W LID
6967
KNOB,LID STEAMER
87 77
2
/6 X 4 STEAM TABLE PAN
88598
3
/6 SIZE PAN LID
69235
4
/3 STEAM PAN LID
69234
Umbrella Parts and Unit Accessories
Item Part Description Part Number
All
Model
s
UMBRELLA
88903
2
UMBRELLA EXTENSION TUBE
88562
3
UMBRELLA ADAPTER BUSHING
88564
4
IN. DIAL THERMOMETER
8000
5
TONG HOLDER
69075
6
9 INCH PLASTIC TONGS
87092
1
2
5 4
3
6

Table Top Steamer Cart Model No. 8080 Series
Page 18
gmpopcorn.com
Wiring Diagram
Model No. 8080 Series

Table Top Steamer Cart Model No. 8080 Series
Page 19
gmpopcorn.com
WARRANTY
© 2015 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241
-
4807 USA
gmpopcorn.com
Phone: [phone] Fax: [phone]
[phone] [phone]