Goldmund EPILOGUE 1 SIGNATURE User manual

USER MANUAL
GOLDMUND EPILOGUE 1 SIGNATURE
Speaker System

User Manual – GOLDMUND Epilogue 1 Signature – 2
Thank you for purchasing the GOLDMUND EPILOGUE 1 SIGNATURE.
Please take some time to read this manual. It may provide you with useful information to make your pleasure
of listening to the Epilogue even higher.
INTRODUCTION
GOLDMUND EPILOGUE 1 SIGNATURE – Speaker System
Goldmund was founded in 1978 and has ever since been dedicated to the accurate reproduction of sound
and image.
At Goldmund, we strive to lead in the creation, development and manufacture of the industry’s most
advanced technologies, including audio and video systems, home-networking and music distribution.
The guiding principle at Goldmund is to produce a precise sound with the least possible loss of quality
through the different stages. Goldmund will never adopt a technology before it is sufficiently developed to
satisfy the high quality standards we set. This is why Goldmund has often rejected mainstream technologies
and developed its own.

User Manual – GOLDMUND Epilogue 1 Signature – 3
W A R N I N G!
These extremely high quality speakers
possess new technical features which are a
necessity for an accurate sound reproduction
in the best audio systems.
Only careful installation and use can provide
the satisfaction you are expecting.
The installation instructions must be
scrupulously carried out and the mentioned
precautions taken to get the expected result
and to avoid deteriorating the speakers.
Nevertheless, if the instructions are perfectly
carried out, you will notice that the sound
quality of your Goldmund Epilogue is
incredibly dynamic, precise and sweet.

User Manual – GOLDMUND Epilogue 1 Signature – 4
CONTENTS
INTRODUCTION ....................................................................................................................... 2
1PRELIMINARIES.......................................................................................................................5
2UNPACKING .............................................................................................................................. 5
3SELECTING THE SPEAKERS LOCATION......................................................................6
4ASSEMBLING THE EPI-FOOT............................................................................................7
5CONNECTING THE AMPLIFIER......................................................................................... 8
6RUNNING-IN ..............................................................................................................................9
7CLEANING ..................................................................................................................................9
8TECHNICAL SPECIFICATIONS .......................................................................................10

User Manual – GOLDMUND Epilogue 1 Signature – 5
1 PRELIMINARIES
The Goldmund Epilogue 1 Signature uses some very innovative technology to achieve a level of
definition and neutrality never found before in a speaker system.
Please read very carefully the following instructions. These high-precision speakers are extremely
revealing and can provide the best sound only if they are used properly.
For exacting technicians, musicians, and all those who demand the very best in audio reproduction,
we strongly recommend the use of the best associated components, especially electronics and cables
(see paragraph 5).
2 UNPACKING
It is easier to be two people to install the Epilogue 1 Signature since the speakers are extremely
heavy and some handling steps necessitate a lot of care.
Open the two cartons and remove the speakers. If you have purchased the Epi-Foot set of supports
for the Epilogue, open the feet box too and remove the feet parts. Unpack the speakers close to the
location where they will be standing.
ATTENTION: If you need to return the speakers to the factory or to your local representative for a
warranty repair, please note that it must be repacked in the original packing. This packaging has been
designed specifically to protect the Epilogue 1 Signature in transit. Use of alternative packaging is
likely to result in damage, invalidating warranty cover.

User Manual – GOLDMUND Epilogue 1 Signature – 6
3 SELECTING THE SPEAKERS LOCATION
If you decided not to use the Goldmund Epi-Foot supports, you will need a very strong support for the
Epilogue.
A very rigid floor is very important for the optimal sonic result of your Epilogue speakers. Especially if
you use the Epi-Foot, select a position of the speaker to have the most rigid possible coupling with the
floor. Solid coupling is essential, and if your support is standing on a suspended floor, optimal result
requires that you arrange the support to have at least the pointed foot above a supporting beam or
close enough from a supporting wall.
ATTENTION: The pointed feet included in the Epi-Foot are very hard. They are designed to go
through a carpeted floor. If your floor is made of wood or tile, be careful not to scratch it by moving a
speaker without lifting the point.

User Manual – GOLDMUND Epilogue 1 Signature – 7
4 ASSEMBLING THE EPI-FOOT
•First put the speaker on its side on the floor. Use a soft cushion to avoid damaging it.
•Screw the pointed bar in the threading accessible in the speaker’s bottom plate. Tighten it as
much as you can.
•Put some soap on the bar near the pointed end in order to slide it easier into the 2 rubber
centering rings of the foot assembly.
•Slide the foot on the bar. You can make it easier by turning the speaker with the pointed bar
toward the ceiling.
•Lift the speaker and put it on its foot.
•Adjust the 4 leveling screws of each foot to provide a stable position to the speaker.

User Manual – GOLDMUND Epilogue 1 Signature – 8
5 CONNECTING THE AMPLIFIER
The Epilogue 1 Signature needs to be powered by 2 amplifiers as it does not include a passive filter.
This system has to be used with a preamplifier enabling digital filters to be implemented. To benefit
from the Proteus technology and Leonardo time correction developed by Goldmund, we recommend
using The Mimesis 16, Mimesis 16HD or Mimesis 32 preamplifiers.
If you do not use Goldmund amplifiers, make sure to select amplifiers with sufficient speed and
dynamic range to do justice to the qualities of the Epilogue. Slow amplifiers will not have the capability
to properly hold the ultra-fast drivers of the Epilogue 1 Signature.
The cables coming from the amplifiers have to be connected to the back panel plug connectors. The
upper connectors drive the tweeter section and the lower connectors the woofer section. You can use
the large coaxial connectors or the banana ones. In this last case, make sure to use high quality
banana plugs which can be tighten in position.
Try using the Goldmund Speaker Cable to allow the speed of the amplifier to properly control the
drivers of the speaker. Any cable of lower quality or speed can ruin the sonic capabilities of the
Epilogue 1 Signature.
When using the Goldmund High-Definition Speaker Cable, the Speaker Adapter can be avoided and
the coaxial cable directly connected to the large coaxial connector provided on the speaker back
panel. The sonic improvement which can be achieved in the best systems is quite significant.

User Manual – GOLDMUND Epilogue 1 Signature – 9
6 RUNNING-IN
The Epilogue 1 Signature needs many days playing music before providing the top sonic quality they
are built to provide.
The few first hours can be very frustrating for a demanding listener.
Do not hesitate to let them play quite loud for some time before attempting any real system tuning or
position adjustment.
7 CLEANING
To clean the metal case of the speaker, you can use a wet cloth. Always use a very soft cloth to avoid
scratching the surface.
The identification plates are gold plated. Simply clean them with a soft cloth, without any chemical
solution.

User Manual – GOLDMUND Epilogue 1 Signature – 10
8 TECHNICAL SPECIFICATIONS
EFFICIENCY
•89.5 dB
BANDWITH
•Low Frequency Cutoff: < 34 Hz -3dB
•High Frequency Cutoff: > 28 kHz
DRIVERS
•1 x 17 cm low frequency proprietary driver
•1 x dome tweeter
BASS LOAD
•Flexible Vent loading
SIZE & WEIGHT
•Weight of one Epilogue 1 Signature: 43 kg
•Size of one Epilogue 1 Signature: 36 cm (H) x 23 cm (W) x 42 cm (D)