Golfsport GSK User guide

GSK
HOME GOLF
IMPACT BOX
Setup Manual
EU/US Units
Version 1.21 - Y2019
Golfsport Company KG
Am Kanal 2a/5
A-2482 Muenchendorf
Austria
E-Mail Contact / Setup Assistance:
[email protected]

1. Connect the Tubes:
In the Package Box 1 and 2 you nd 45x45mm Tubes
6 x 150 cm = 4ft 11in = Label E
6 x 125 cm = 4ft 1in = Label A
2 x 120,5 = 3ft 11in = Label B
2 x 111 cm = 3ft 7in= Label C
2 x 130 cm = 4ft 3in = Label D
also you have
7 Flat Prole Steel connectors to connect the Tubes together.
You rst connect this Tubes with the Tube Connectors!
So you have tubes of the below sizes ready to install.
You can see on the Sketch on Sketch Pages later in this docuiment where the Tubes are Finaly
located
3 x 300 cm / 9ft 10in = 150 cm + 150 cm Tubes = Use Tube E+E
2 x 250 cm / 8ft 2in = 125 cm + 125 cm Tubes = Use Tube A + A
2 x 245,5 cm / 8ft 1in = 125 x 120,5 cm Tubes = Use Tube A + B
2 x 130 cm / 4ft 3in = 130 cm Tube = Tube D
2 x 111 cm / 3ft 7in = 111 cm Tube = Tube C
Now you are ready to build the GSK Golf Box.

E + E
3 x 300 cm
9ft 10in
A + A
2 x 250 cm
8ft 2in
A + B
2 x 245,5 cm
8ft 1in
D
2 x 130 cm
4ft 3in
C
2 x 111 cm
3ft 7in

2. Sidewall Setup:
Build this 2 Times for 2 Sidewalls:
Build the Sidewalls as shown with the 90° Angle connec-
tors attached in each corner, as shown in the picture.
Reference on the Sketch Side View, how it nally should
look.
It does not matter how you install the 90° Angle Connec-
tors, inside or outside facing.
The distance on the top side to side is 120 cm / 3ft 11in
The distance on the ooor side to side is 130 cm / 4ft 3in
You need following Tubes:
1 x 250 cm = 8ft 2in
1 x 245,5 cm = 8ft 1in
1 x 111 cm = 3ft 7in
1 x 130 cm = 4ft 3in
4 x 90° Connectors plus Screws
Please see the pictures and Sketch how to connect the 2
Sidewalls Bars to each other.
111 cm
130 cm
Velcro for 120 cm
125 cm 125 cm
120,5 cm
Tube Connector 4 Screws
Looking Inside the Construction
125 cm
4,5 cm
Side View
Velcro both sides for 250 cm
Velcro centered approx 90 cm
B
C
D
A
A
A

Please use now the delivered Velcro Tape and stick it as in the picure on the Sidewalls please see
the Sketch and the Pictures for your Reference.

Now lift the sidewalls and connect with one 300 cm / 9ft 10in Tube on the Floor with both Side-
walls as Shown in the 3 D Sketch Plan, and connect it with the 2 Angle Connector, the Angle
Connectors should mounted parallel to the Floor, as in the Picture below.
The Sides with the Velcro must face inside the Box
The Sidewalls should now stand themselves.

TOP Tubes Mount:
Put 2 x 300 cm / 9ft 10in Tube on the Top of the Box and Connect this as well with Angle Con-
nectors to the side walls.
See the Pictures and the Sketch 3D for Reference how the Tubes should be mounted.
Put Velcro Tape on the Top Tubes
Both Top Tubes Facing inside = Down to the Floor for 291 cm with Velcro
Back Tube where the Screen is mounted - Side Facing to ceiling for 300 cm with Velcro

Fabric Install
Sidewalls:
There are 2 Sidewalls, each dedicated to its own side.
Use the Velcro to put the Fabric on to the Sidewalls, start from the top and then stretch it out
downwards.
The “Flausch” Velcro facing inside the Box has to be on the side where the Screen is mounted.
Repeat that on the second side as well.

Impact Screen NEW Version
Top / Upper Side:
Use the Hammerscrews approx 25mm Long, and and 8 mm NUT, for the Fixed mount of the Im-
pact Screen on the Top Bar. Hammerscrew through the Eyelet and mounting with the Nut.
The Postion of the Screen is direclty inside of the Box, as you see in the Picture Below.
Stretch then the screen and screw it on the Top Bar, so it is on Top as Flat as Possible.
The use a Fast Fix on the Left and Right Bottom to stretch the Impact Screen out - this already
would be enough of tension, to have a at screen.
Left / Right Sides:
Then position the attached rolls always in the middle of the eylets (eyes) as shown in sketch, on
the Left and Right post.
Now use the bungee cord and start as in the Sketch shown to stretch out the Impact screen with
the bungee, and fasten it with the Black Fast Fix.
It should be strechted but should be still exible and soft, this should take no real force to have
this done.
Side Latches:
Now velcro the Latches of the Screen to the Side walls, so the Sides are protected, and the Ball
can not exit the Cage.

Roof
Now Install the Roof, the Latch must face towards the Impact Screen.
See the pictures for an detailed install of the screen.
The Roof latches should prevent high Shots from hitting the top post and/or leaving the box itself.