golmar RD-G2+ User manual
Code 50122552 TRD-G2 E+ N REV.0121
RD-G2+
DIGITAL REPEATER
TEC NOLOGH Y
12258960 V02
RD-G2+ REPEATER
GOLMAR S.A.
C/ Silici, 13
08940-SPAIN
MADE IN CHINA
IN
POWER
OUT
IN OUT PL PL FA FA
INSTRUCTIONS MANUAL
CONTENTS
2
SET-UP WARNINGS
-Do not overtighten the screws on the RD-G2+ connector.digital repeater o em dul
-Before connecting the device, check the connections between the power supply unit, door panel, distributors, RD-
G2+ modules, monitors, telephones and hands-free audio terminals.
-Use the Golmar cable (2x1mm ).RAP-2150 2
-Always follow the instructions contained in this manual.
Introduc .......................................................................................................................................................... ........tion .
Contents . .............................................................................................................................................................. ........ .
Set-up warnings............................. .. ......................................................................................................... ........... ..........
Safety precautions............. ................................................................................................................................. ...........
C aracter stics.................................................................................................................................................. ............h i .
RAP-2150 cable characteristics ................. .(Golmar)................ ......................................................................... ...........
Operating modes.............. . ................................................................................................................................. .. ............
A mode........... . ...mplifier ................................................................................................................................ ... ..........
P ............ ...ower mode ..............................................................................................................................................
B ........... .. .lock mode ....................................................................................................................................... ........ .
Descrip m dul .............................................................................................. ...... ....tion of the RD-G2+ digital repeater o e . ...
Descrip ................................................................................................................................................ .. ...........tion .. .
Instal a i n................................................................................................................................................... ............... .l t o .. ...
Illustration of RD-G2+ digital repeater module installation . .............................................................................. ...... .....
Descrip ................................................................................... .. ..tion of the DIP switches.................................... ...... .
Configurin )... .......................................................g the button code (up to 32 addresses/apartments ................... ..
Configur ( 128 / ). ....................................................ing the button code up to addresses apartments ................... .....
Wiring diagrams .............. . ... .... ............................................................................................................................... . . .....
Instal a " " ................... ....l tion of video door entry system with RD-G2+ mode of the monitors bus.......... .. .....amplifier
Instal a "power mode" .............. ........... .l tion of video door entry system with RD-G2+ .................................... ....... ..
Instal al tion of audio door entry system with mode ................................................. ...... .RD-G2+ "block " ..................... .
Instal a “block " ..................... .l tion of video door entry system with RD-G2+ mode ............................................ ...... .
Instal a ..................l tion of audio and video door entry system with 1 access panel.................................................. ...
Instal a .....................................................................l tion of audio and video door entry system with 2 access panels .
Instal a .....................................................................l tion of audio and video door entry system with 4 access panels .
Con Golmar.................................................................................. ........nection of Golmar DC anAC lock releases. ....
2
2
2
3
3
3
4
5-6
7-9
10
10
11
1 -12 5
16-25
26
2 -27 9
30
31 5-3
36
37
38
39
RD-G2+ DIGITAL REPEATER
INTRODUCTION
First and foremost we would like to thank you for purchasing this product.
Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification
and the manufacture of products like the one you have just purchased.
Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features
that this device offers. To get the most out of them and ensure proper operation from day one, we recommend that you
read this instruction manual.
3
C ARACTERÍSTICH S
- ).RD-G2+ digital repeater module with simplified wiring (non-polarised 2-wire bus
- :RD-G2+ digital repeater module for the G2+ system that allows the following operating modes
wAmplifi mode:er
-Allows to increase the monitor bus distance, 1 RD-G2+ module "amplifier mode" and 1 RD-G2+ module "power
mode" with its power supply unit FA-G2+ are required (see page 4 and 26).
-Allows to increase the bus distance in a "power mode" or "block mode" system when it is more than 300 m
between the and the first RD-G2+ "amplifier mode" (see page 5, 9, 29 and 35).door panel
Important: Up to 4 RD-G2+ modules in amplifier mode.
wPower mode:
-Allows 32 additional monitors (max. 4 RD-G2+ and up to 128 elements).
-Allows risers/verticals installation ( a . 32 risers , up to 32 monitores per riser and up to128 monitors in/verticalm x s
installation.
-Up to 4 door panels.
-Door panels with EL632-G2 + SE video module with 'V04' or later for compatibility with this operating mode.,
wBlock mode:
-Allows an installation with up to 4 general door panels and up to 32 buildings with interior door panels.
-Up to 4 door panels e buildingp r interior .
-Up to 4 generals coded panels.
-Up to 32 i terior buildings up to 4 interior door panels per interior buildingn ( ).
-RD-G2+ module “block mode”with its FA-G2+ power supply per inner building.
-Door panels with EL632-G2 + SE video module with 'V04' or later for compatibility with this operating mode.,
- FA-G2+ power supply unit is required for each RD-G2+ module in "power mode" and "block mode".
- It is necessary to configure the operating mode.
- ).DIP switches (operating mode, building address number “ ” and end of lineblock mode
- Led.Power supply status
RAP-2150 (GOLMAR) CABLE CHARACTERÍSTICS
SAFETY PRECAUTIONS
-Always disconnect the power supply before installing or making modifications to the device.
- The fitting and handling of this device must be carried out by authorised personnel.
- The wiring must run at list 40 cm. de cualquier otra instalación.
- Install the RD-G2+ module in a dry protected location free from risk of dripping or splashing water.
- Install the module “ ” and “ ” together with its FA-G2+ power supplyRD-G2+ power mode block mode .
-Avoid locations that are humid, dusty or near heat sources.
-Ensure that the air vents are free from obstruction so that air can circulate freely.
-To prevent damage, the RD-G2 module must be firmly secured in place.+
RD-G2+ DIGITAL REPEATER
Electrical resistance of the conductor at 20°C
ELECTRICAL CHARACTERISTICS
19 5 /Km.
Capacity between conductors
Characteristic impedance
VALUES
CONSTRUCTION CHARACTERISTICS
Class V
VALUES
Flexible 1mm twisted pair polished copper conductor
2
45pf/m 10%
100 10%
15 V/m
Wiring
4
OPERATING MODE MODE: (AMPLIFIER )
G2+ building installation
with RD-G2 on monitor bus+
*
( )
(Distances with Golmar cable (twisted pair 2x1mm ).RAP-2150
2
- This operating mode allows to increase the distance of the monitor bus when it exceeds 190m (distance with Golmar
RAP-2150 2x1mm twisted pair cable) see age, p 26.
1 RD-G2+ module "amplifier mode" and 1 RD-G2+ module "power mode" with its power supply unit FA-G2+ are required.
Important: It is not allowed to increase the distance of the panel bus.
- This operating mode allows to increase the bus distance in a "power mode" or "block mode" system when it is more than
300 m between the and the first RD-G2+ "amplifier mode" (see page 5, 9, 29 and 35).door panel
IMPORTANT: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
D -G24L +
A
E
FA-G2+
RD-G2+
F1
Monitor bus
EL632 G2+ SE
Power mode
RD-G2+
Amplifier
mode
F2
F3
B
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment 29
Apartment 30
Apartment 3 Apartment 4
Apartment 31Apartment 32
ART 4/
ART 7H/
ART 7W/
Apartment 1 Apartment 2
C
FA-G2+
ABC
80m 80m 80m
Cable D
30m
B+ +CD
190m
E
15m
RAP-GTWIN/HF 2x1mm
2
F1 F2
220m 220m
F3
80m
A+F1
300m
B+++CDF3
300m
*
( )
Distanc se and cross-sections:
E :xample installation type
- 32 monitors ART 4 G2+ / ART 4 G2+ LITE.with
- 32 monitors ART 7H G2+ / ART 7 G2+ LITE.with
- 32 monitors ART 7W/G2+.with
A
E
FA-G2+
G2+ building installation
Monitor bus
Door panel bus
EL632 G2+ SE
D -G24L +
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment 29
Apartment 30
Apartment 3 Apartment 4
Apartment 31 Apartment 32
ART 4/
ART 7H/
ART 7W/
Apartment 1Apartment 2
C
B
123
ON DIP
4 5 6 7 8
123
ON DIP
4 5 6 7 8
PL
PL
M
FA
IN
FA
PL
M
PL
M
2
RD-G2+ DIGITAL REPEATER
Door panel bus
5
OPERATING MODE: ( AMPLIFIER MODE)POWER MODE WITH
Installation with 1 building, 128 monitors, 4 RD-G2+ “power mode”, 1RD-G2+ “amplifier mode” and 4 door panels.
F
FA-G2+
DPM-G2+
E
BUILDING 1
D -G24L +
D -G24L +
D
End of line
ON
OFF
End of line
ART 4/
ART 7H/
ART 7W/
Apartment29
Apartment30
Apartment 3 Apartment 4
Apartment 31 Apartment 32
ART 4/
ART 7H/
ART 7W/
Apartment 1 Apartment 2
D -G24L +
D -G24L +
D
End of line
ON
OFF
End of line
ART 4/
ART 7H/
ART 7W/
Apartment61 Apartment62
Apartment 35 Apartment 36
Apartment 63 Apartment 64
ART 4/
ART 7H/
ART 7W/
Apartment 33 Apartment 34
D -G24L +
D -G24L +
D
End of line
ON
OFF
End of line
ART 4/
ART 7H/
ART 7W/
Apartment 93 Apartment 94
Apartment 67 Apartment 68
Apartment 95 Apartment 96
ART 4/
ART 7H/
ART 7W/
Apartment 65 Apartment 66
D -G24L +
D -G24L +
D
End of line
ON
OFF
End of line
ART 4/
ART 7H/
ART 7W/
Apartment125 Apartment 126
Apartment 99 Apartment100
Apartment127 Apartment128
ART 4/
ART 7H/
ART 7W/
Apartment 97 Apartment 98
Lock release
max. 12 Vdc/270mA
( )
*
AA1
A2 A3
A4
FA-G2+
RD-G2+(1)
FA-G2+
RD-G2+(2)
FA-G2+
RD-G2+(3)
FA-G2+
RD-G2+(5)
C C C
( )
*( )
*( )
*( )
*
B B B B
C
IN OUT
FA
PL
M
A1=A2=A3=A4= 80m.
Important:
Max. distancia of 300m from door panel to first RD-G2+
“amplifier mode”.configured as
( )
1
E :xample installation type
- 32 monitors ART 4 G2+ / ART 4 G2+ LITE.with
- 32 monitors ART 7H G2+ / ART 7 G2+ LITE.with
- 32 monitors ART 7W/G2+.with
Max. distance 1m.
Distanc s :e and cross-sections
ABC
80m
Cable D
30m
B+ +CD
190m
E
15m
RAP-GTWIN/HF 2x1mm
2
( )
*
80m 80m
F
220m
A+F
300m
( )
1
Door panels
Technical room
IN OUT
FA
PL
M
IN OUT
FA
PL
M
IN
FA
PL
M
Technical room
Technical roomTechnical room
Technical room
1 2 3
ON DIP
4 5 6 7 8 1 2 3
ON DIP
4 5 6 7 8 123
ON DIP
4 5 6 7 8
Power mode Power mode Power mode
123
ON DIP
4 5 6 7 8
Power mode
RD-G2+(4)
PL FA
1 2 3
ON DIP
4 5 6 7 8
Amplifier
mode
F1
( )
1
Note:
Note:
For more information see characteristics on page 3.
F1
220m
Technical room
RD-G2+ DIGITAL REPEATER
6
OPERATING MODE POWER MODE: ( )
Installation with 1 building, 128 monitors, RD-G2+ “power mode” and 4 door panels.3
F
FA-G2+
DPM-G2+
E
BUILDING 1
D -G24L +
D -G24L +
D
FINAL LINEA
ON
OFF
FINAL LINEA
ART 4/
ART 7H/
ART 7W/
Apartment29
Apartment30
Apartment 3 Apartment 4
Apartment 31 Apartment 32
ART 4/
ART 7H/
ART 7W/
Apartment 1 Apartment 2
D -G24L +
D -G24L +
D
FINAL LINEA
ON
OFF
FINAL LINEA
ART 4/
ART 7H/
ART 7W/
Apartment61 Apartment 62
Apartment 35 Apartment 36
Apartment 63 Apartment 64
ART 4/
ART 7H/
ART 7W/
Apartment 33 Apartment 34
D -G24L +
D -G24L +
D
FINAL LINEA
ON
OFF
FINAL LINEA
ART 4/
ART 7H/
ART 7W/
Apartment 93 Apartment 94
Apartment 67 Apartment 68
Apartment 95 Apartment 96
ART 4/
ART 7H/
ART 7W/
Apartment 65 Apartment 66
D -G24L +
D -G24L +
D
FINAL LINEA
ON
OFF
FINAL LINEA
ART 4/
ART 7H/
ART 7W/
Apartment125 Apartment 126
Apartment 99 Apartment100
Apartment127 Apartment128
ART 4/
ART 7H/
ART 7W/
Apartment 97 Apartment 98
( )
*
AA1
A2 A3
A4
FA-G2+
RD-G2+(1)
FA-G2+
RD-G2+(2)
FA-G2+
RD-G2+(3)
C C C
( )
*( )
*( )
*
B
B B B
C
B SU
ABC
80m
Cable D
30m
B+ +CD
190m
E
15m
RAP-GTWIN/HF 2x1mm
2
80m 80m
F
220m
A+F
300m
( )
1
Technical room
IN OUT
FA
PL
M
IN OUT
FA
PL
M
IN
FA
PL
M
Technical room
Technical roomTechnical room
Technical room
D -G22L +
D1
IN
B SU
OFF
FINAL LINEA
1 2 3
ON DIP
4 5 6 7 8 1 2 3
ON DIP
4 5 6 7 8 1 2 3
ON DIP
4 5 6 7 8
Power mode Power mode Power mode
( )
1
RD-G2+ DIGITAL REPEATER
Lock release
max. 12 Vdc/270mA
A1=A2=A3=A4= 80m.
Important:
Max. distancia of 300m from door panel to first RD-G2+
“amplifier mode”configured as (see page 5 with “amplifier mode).
E :xample installation type
- 32 monitors ART 4 G2+ / ART 4 G2+ LITE.with
- 32 monitors ART 7H G2+ / ART 7 G2+ LITE.with
- 32 monitors ART 7W/G2+.with
Max. distance 1m.
Distanc s :e and cross-sections
( )
*
Door panels
Note:
Note:
For more information see characteristics on page 3.
7
Installation with 4 buildings, 128 audio terminals per building, 16 interior door panels and 4 general code door panels.
F
FA-G2+
DPM-G2+
E
BUILDING 2
D -G24L +
D
ART 1/
T-ART
Apartment127
ART 1/
T-ART
BUILDING 1
D -G24L + D -G24L + D -G24L +
BUILDING 4BUILDING 3
Lock release
max. 12 Vdc/270mA
Max. distance 1m.
Distanc s :e and cross-sections
ABC
80m
Cable D
15m
B+ +
CD
130m
F
220m
RAP-GTWIN/HF 2x1mm
2
( )
*
20m 96m
( )
*
GG1
G2 G3
G4
FA-G2+
RD-G2+(1)
FA-G2+
RD-G2+(2)
FA-G2+
RD-G2+(3)
FA-G2+
RD-G2+(4)
C
( )
*( )
*( )
*( )
*
B B B B
G
80m
G+F
300m
IN OUT
FA
PL
M
Building 4
Up to 4 interior
door panels as
building 1.
PL PL
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
IN OUT
FA
PL
M
IN OUT
FA
PL
M
IN OUT
FA
PL
M
PL
Building 1 Building 2 Building 3
General
door panels
Important:
Max. distancia of 300m from door panel to first RD-G2+
configured as “amplifier mode”(see page 9 with “amplifier mode”).
( )
1
( )
1
E
15m
Technical room
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
Technical room
PL
Technical room Technical room
OPERATING MODE BLOCK MODE: ( -AUDIO DOOR PANEL)
123
ON
DIP
45678
Building1
Block mode
OFFEnd of line
RD-G2+ configuration DIP switches:
A1=A2=A3=A4= 80m.
G1=G2=G3=G4= 80m.
Note:
( )
1
Note:
For more information see characteristics on page 3
123
ON
DIP
45678
Building 2
Block mode
End of line OFF
123
ON
DIP
45678
Building 3
Block mode
End of line OFF
123
ON
DIP
45678
Building 4
Block mode
End of line ON
Apartment 2
AUX
AUX
Apartment 128
AUX
AUX
Make the connections in
electrical junction box.
D
ART 1/
T-ART
Apartment127
ART 1/
T-ART
C
AUX
AUX
Apartment 128
AUX
AUX
Make the connections in
electrical junction box.
D
ART 1/
T-ART
Apartment127
ART 1/
T-ART
C
AUX
Apartment 128
AUX
AUX
Make the connections in
electrical junction box.
D
ART 1/
T-ART
Apartment127
ART 1/
T-ART
C
AUX
AUX
Apartment 128
AUX
AUX
Make the connections in
electrical junction box.
Apartment 1 Apartment 2Apartment 1
AUX
Apartment 2Apartment 1 Apartment 2Apartment 1
RD-G2+ DIGITAL REPEATER
8
Installation with 4 buildings, 128 monitors, 16 interior door panels and 4 general door panels.
F
FA-G2+
DPM-G2+
E
BUILDING 2
D -G24L +
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment29
Apartment30
Apartment 3 Apartment 4
Apartment 31 Apartment 32
ART 4/
ART 7H/
ART 7W/
BUILDING 1
Apartment 1 Apartment 2
D -G24L +
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment61 Apartment 62
Apartment 35 Apartment 36
Apartment 63 Apartment 64
ART 4/
ART 7H/
ART 7W/
Apartment 33 Apartment 34
D -G24L +
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment 93 Apartment 94
Apartment 67 Apartment 68
Apartment 95 Apartment 96
ART 4/
ART 7H/
ART 7W/
Apartment 65 Apartment 66
D -G24L +
D -G24L +
D
END OF LINE
ON
OFF
END OF LINE
ART 4/
ART 7H/
ART 7W/
Apartment125 Apartment 126
Apartment 99 Apartment100
Apartment127 Apartment128
ART 4/
ART 7H/
ART 7W/
Apartment 97 Apartment 98
BUILDING 4BUILDING 3
ABC
80m
Cable D
30m
B+ +
CD
190m
F
220m
RAP-GTWIN/HF 2x1mm
2
80m 80m
( )
*
GG1
G2 G3
G4
FA-G2+
RD-G2+(1)
FA-G2+
RD-G2+(2)
FA-G2+
RD-G2+(3)
FA-G2+
RD-G2+(4)
C C C
( )
*( )
*( )
*( )
*
B B B B
G
80m
G+F
300m
C
IN OUT
FA
PL
M
Building 4
Up to 4 interior
door panels as
building 1.
PL PL
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
IN OUT
FA
PL
M
IN OUT
FA
PL
M
IN OUT
FA
PL
M
PL
Building 1 Building 2 Building 3
( )
1
E
15m
Technical room
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
Technical room
PL
Technical room Technical room
OPERATING MODE: ( )BLOCK MODE
( )
1
RD-G2+ DIGITAL REPEATER
Lock release
max. 12 Vdc/270mA
Distanc s :e and cross-sections
General
door panels
Important:
Max. distancia of 300m from door panel to first RD-G2+
configured as “amplifier mode”(see page 9 with “amplifier mode”).
( )
1
123
ON
DIP
45678
Building1
Block mode
OFFEnd of line
RD-G2+ configuration DIP switches:
A1=A2=A3=A4= 80m.
G1=G2=G3=G4= 80m.
Note:
123
ON
DIP
45678
Building 2
Block mode
End of line OFF
123
ON
DIP
45678
Building 3
Block mode
End of line OFF
123
ON
DIP
45678
Building 4
Block mode
End of line ON
E :xample installation type
- 128 monitors ART 4 G2+ / ART 4 G2+ LITE.with
- 128 monitors ART 7H G2+ / ART 7 G2+ LITE.with
- 128 monitors ART 7W/G2+.with
Note:
For more information see characteristics on page 3.
Max. distance 1m.
( )
*
9
Installation with 4 buildings, 128 monitors, 16 interior door panels, 1RD-G2+ “amplifier mode” and 4 general door panels.
F
FA-G2+
DPM-G2+
D -G24L +
D -G24L +
D
ON
OFF
ART 4/
ART 7H/
ART 7W/
Apartment29
Apartment 30
Apartment 3 Apartment 4
Apartment 31 Apartment 32
ART 4/
ART 7H/
ART 7W/
Apartment 1 Apartment 2
D -G24L +
D -G24L +
D
ON
OFF
ART 4/
ART 7H/
ART 7W/
Apartment61 Apartment 62
Apartment 35 Apartment 36
Apartment 63 Apartment 64
ART 4/
ART 7H/
ART 7W/
Apartment 33 Apartment 34
D -G24L +
D -G24L +
D
ON
OFF
ART 4/
ART 7H/
ART 7W/
Apartment 93 Apartment 94
Apartment 67 Apartment 68
Apartment 95 Apartment 96
ART 4/
ART 7H/
ART 7W/
Apartment 65 Apartment 66
D -G24L +
D -G24L +
D
ON
OFF
ART 4/
ART 7H/
ART 7W/
Apartment125 Apartment 126
Apartment 99 Apartment100
Apartment127 Apartment128
ART 4/
ART 7H/
ART 7W/
Apartment 97 Apartment 98
EDIFICIO 4
ABC
80m
D
30m
B+ +
CD
190m
F
220m
RAP-GTWIN/HF 2x1mm
2
80m 80m
( )
*
GG1
G2 G3
G4
FA-G2+
RD-G2+(1)
FA-G2+
RD-G2+(2)
FA-G2+
RD-G2+(3)
FA-G2+
RD-G2+(5)
C C C
( )
*( )
*( )
*( )
*
B B B B
G
80m
G+F
300m
C
IN OUT
FA
PL
M
PL PL
IN OUT
FA
PL
M
IN OUT
FA
PL
M
IN OUT
FA
PL
M
PL
( )
1
E
15m
Technical room
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
DPM-G2+
A
A1
A2 A3
A4
E
( )
*
Technical room
PL
Technical room Technical room
Building 3
Up to 4 interior
door panels as
building 1.
RD-G2+(4)
PL FA
123
ON
DIP
45678
Amplifier
mode
F1
220m
F1
( )
1
OPERATING MODE: ( WITH AMPLIFIER MODE)BLOCK MODE
E
RD-G2+ DIGITAL REPEATER
Distanc s :e and cross-sections
E :xample installation type
- 128 monitors ART 4 G2+ / ART 4 G2+ LITE.with
- 128 monitors ART 7H G2+ / ART 7 G2+ LITE.with
- 128 monitors ART 7W/G2+.with
Note:
For more information see characteristics on page 3.
Max. distance 1m.
( )
*
Cable
BUILDING 2
END OF LINE
END OF LINE
BUILDING 1
END OF LINE
END OF LINE
END OF LINE
END OF LINE
END OF LINE
END OF LINE
BUILDING 3
Building 4
Up to 4 interior
door panels as
building 1.
Building 1 Building 2
Lock release
max. 12 Vdc/270mA
General
door panels
Important:
Max. distancia of 300m from door panel to first RD-G2+
configured as “amplifier mode”.
( )
1
123
ON
DIP
45678
Building1
Block mode
OFFEnd of line
RD-G2+ configuration DIP switches:
A1=A2=A3=A4= 80m.
G1=G2=G3=G4= 80m.
Note:
123
ON
DIP
45678
Building 2
Block mode
End of line OFF
123
ON
DIP
45678
Building 3
Block mode
End of line OFF
123
ON
DIP
45678
Building 4
Block mode
End of line ON
10
DESCRIPTION OF THE RD-G2+ DIGITAL REPEATER MODULE
Descrip :tion
INOUTPLFA
FRONT TOP
BOTTOM
a.
b.
c.
d.
Power status Led.
Label.
“FA”connection terminals.
“PL”connection terminals..
“IN”connection terminals.
“OUT”.connection terminals
Configuration DIP switch.
DIN .rail latch release
e.
f.
g.
h.
The RD-G2 module can be mounted onto a DIN+
rail (4 elements) by applying slight pressure.
To remove the RD-G2 module from the DIN rail,+
use a flat screwdriver to lever it off, as shown in
the drawing.
Install the module in a dry protected location free from the risk of dripping or splashing water.RD-G2+
DIN 46277
INSTA LA I NL T O
Illustration of RD-G2+ digital repeater module:
c
d
g
h
123
ON DIP
45678
12258960 V02
RD-G2+ REPEATER
GOLMAR S.A.
C/ Silici, 13
08940-SPAIN
MADE IN CHINA
IN
POWER
OUT
IN OUT PL PL FA FA
a
b
c
d
e
f
12258960 V02
RD-G2+ REPEATER
GOLMAR S.A.
C/ Silici, 13
08940-SPAIN
MADE IN CHINA
IN
POWER
OUT
IN OUT PL PL FA FA
Note: See installation diagrams for wiring.
( )
*
( )
*
( )
*
( )
*
( )
*
RD-G2+ DIGITAL REPEATER
11
The DIP switches of the RD-G2 module enable configuration of one of the 3 operating modes+ , building address
number “ ” and end of lineblock mode .
Description of the DIP switches:
1 2 3
ON DIP
456
Configur :ing the operation mode
Amplifier mode:
DIP switches: 1 set to ON and 2 set to OFF.
Power mode:
DIP switches: 1 set to OFF and 2 set to ON.
Block mode:
DIP switches and 2 set to N.: 1 O
No function.
Configuration of the address number in the RD-G2+ module installed in "block mode":
*
( ) Factory setting.
7 8
1 2 3
ON DIP
4 5 6 7 8
1 2 3
ON DIP
4 5 6 7 8
1 2 3
ON DIP
4 5 6 7 8
Dip switches 3 to 7 of the RD-G2+ module allow us to set the address (building) of the RD-G2+ "block mode" (address 1 to
32).
The DIP switches in the OFF position have zero value. In the ON position, they are assigned the values from the table
below. The address code of the RD-G2+ module will be equal to the sum of the values of the switches set to ON.
Important:
- Select a different address number for each RD-G2+ module in "block mode".
Dip switches 3 4 5 6 7:
ON : 1 2 4 8 16value
Tabl vale of ues
1 2 3
ON
Example: 1+ 0+4 0+0 5+ =
4 5 6 7 8
Important:
-Address 1: (Dip3 set to ON & Dip4-Dip7 set to OFF)
-Address 32 (Dip3 - Dip7 set to OFF).
Configur :ing the end of line on the RD-G2+ module
1 2 3
ON DIP
4 5 6 7 8
Interruptor 8 a ON
123
ON DIP
45678
Interruptor 8 a OFF
DIP switch 8 of the RD-G2+ activates the end-of-line resistance in the ON position. Activate it in monitors where the bus
cable ends. Deactivate it only in intermediate monitors.
DIP
*
( )
The DIP switches 1 and 2 of the RD-G2+ module allow us to configure between one of the 3 operating modes.
RD-G2+ DIGITAL REPEATER
INSTAL A IL T ON
12
The EL610D button module needs to be configured in order to assign
a call code to the buttons. Carry out this configuration with the
DIP switch located at the back of the module.
Depending on the configuration option selected, the buttons will be
assigned with a certain call code.
To configure the call code on the monitors. It is worth noting the call
code of each button, as shown in the table below.
*
( )
Configuring the button code (video installation up to 32 addresses/apartments:
Important: Select a different configuration option for each EL610D module..
For description, installation, configuration and programming of the door panel, EL610D module andImportant:
monitors, see manual enclosed with the corresponding door panel and monitor.
Note: EL632 G2+ SE V04 & later, setting c d "128" n P1 "127" n P2.module factory with the o e i and i
Note: 3 SE module V04 & later P1 and P2 push buttons must be changed the call codeEL6 2 G2+ ,
(for example "32" in P1 and "31" in P2), see manual: https://doc.golmar.es/search/manual/50122528
(page 28).
*
( ) Factory .setting
EL610D button module
2
Dip1
1
3
Dip2
Dip3
Dip4
Dip5
Dip6
Dip7
Dip8
Module configuration option
P1
1
21
11
DIP switch
On
Off
Off
Off
Off
On
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
Button code
P2 P3 P4 P5 P6 P7
2
22
12
3
23
13
4
24
14
5
25
15
6
26
16
7
27
17
8
28
18
9
29
19
10
30
20
P8 P9 P10 (1)
*
( )
2
Dip1
1
4
6
3
5
7
Dip2
Dip3
Dip4
Dip5
Dip6
Dip7
Dip8
P1
1
11
21
31
6
16
26
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
On
On
On
On
On
On
On
P3 P5 P7 P9
2
12
22
_
7
17
27
3
13
23
8
18
28
4
14
24
9
19
29
5
15
25
10
20
30
(1)
*
( )
Double button module codes
Single button module codes
_ _ _
P1- P10: Button 1 - button 10.
(1)
RD-G2+ DIGITAL REPEATER
INSTAL A IL T ON
13
Configuring double button module codes:
INSTAL A IL T ON
EL632 G2+ SE
P1P2 P2
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
EL610D
12
Front Back
Monitor Code Monitor CodeMonitor Code
Code 13 Code 32
Code 10 Code 9
Code 8 Code 7
Code 6 Code 5
Code 4 Code 3
Code 2 Code 1
Code 20 Code 19
Code 18 Code 17
Code 16 Code 15
Code 14 Code 13
Code 12 Code 11
Code 30 Code 29
Code 28 Code 27
Code 26 Code 25
Code 24 Code 23
Code 22 Code 12
Cod. 10 Cod. 9
Cod. 8 Cod. 7
Cod. 6 Cod. 5
Cod. 4 Cod. 3
Cod. 2 Cod. 1
Cod. 20 Cod. 19
Cod. 18 Cod. 17
Cod. 16 Cod. 15
Cod. 14 Cod. 13
Cod. 12 Cod. 11
Cod. 30 Cod. 92
Cod. 82 Cod. 72
Cod. 62 Cod. 52
Cod. 42 Cod. 32
Cod. 22 Cod. 12
Cod. 13 Cod. 32
ON
2 3 4 5 6 7 8 9 10
NA2
+AP-
C1 NA1 AP+ C2
AP+
GND
BUSBUS
Relé 2Relé 1
_
12Vdc
NC2
CCTV
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5 8
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
12 3
ON DIP
45
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5 8676 7
ON DIP
1 2 3
ON DIP
4 5
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
12 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
12 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
ART 7W/G2+
ART 7H/G2+
ART 4/G2+
ART 7W/G2+
ART 7H/G2+
ART 4/G2+
6 7 878
( )
*
Note: 3 SE module V04 & later P1 and P2 push buttons must be changed the factory default callEL6 2 G2+ ,
code (for example "32" in P1 and "31" in P2), see page 12.
( )
*
( )
*( )
*
( )
*
( )
*
88676 7
8
8676 7
88676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
Code 10
Code 8
Code 6
Code 4
Code 2
Code 20
Code 18
Code 16
Code 14
Code 12
Code 30
Code 28
Code 26
Code 24
Code 22
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
12 3
ON DIP
45
ON DIP
123
ON DIP
4 5
ON DIP
88676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
8
8676 7
Code 13
1 2 3
ON DIP
4 5 8
ON DIP
1 2 3
ON DIP
4 5 8676 7
ON DIP
88676 7
Code 13
RD-G2+ DIGITAL REPEATER
14
Configuring single button module codes:
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
P1
P2 P2
Not used
EL610D
Code 32
Code 5
Code 4
Code 3
Code 2
Code 1
Code 10
Code 9
Code 8
Code 7
Code 6
Code 15
Code 14
Code 13
Code 12
Code 11
Front Back
Monitor Code
P1
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Cod. 5
Cod. 4
Cod. 3
Cod. 2
Cod. 1
Cod. 9
Cod. 8
Cod. 7
Cod. 6
Cod. 11
Cod. 32
Cod. 10
Cod. 15
Cod. 14
Cod. 13
Cod. 12
12
ON
2 3 4 5 6 7 8 9 10
NA2
+AP-
C1 NA1 AP+ C2
AP+
GND
BUSBUS
Relé 2Relé 1
_
12Vdc
NC2
CCTV
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
12 3
ON DIP
4 5
ON DIP
123
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
4 5
ON DIP
12 3
ON DIP
4 5
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
1 2 3
ON DIP
4 5
ON DIP
ART 7W/G2+
ART 7H/G2+
ART 4/G2+
( )
*
6 7 8
EL632 G2+ SE
Note: 3 SE module V04 & later P1 push button must be changed the factory default call code “128"EL6 2 G2+ ,
(for example "32" in P1), 12.see page
( )
*
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
RD-G2+ DIGITAL REPEATER
Continued overleaf
INSTAL A IL T ON
15
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
EL610D
Code 25
Code 24
Code 23
Code 22
Code 21
Code 30
Code 29
Code 28
Code 27
Code 26
Code 31
Code 20
Code 19
Code 18
Code 17
Code 16
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Cod. Monitor
Cod. 20
Cod. 19
Cod. 18
Cod. 17
Cod. 16
Cod. 25
Cod. 24
Cod. 23
Cod. 22
Cod. 21
Cod. 30
Cod. 29
Cod. 28
Cod. 27
Cod. 26
Cod. 13
12 3
ON DIP
4 5
ON DIP
1 2 3
ON
4 5
ON
1 2 3
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
12 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
123
ON DIP
4 5
ON DIP
1 2 3
ON DIP
4 5
ON DIP
1 2 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
123
ON DIP
45
ON DIP
12 3
ON DIP
45
ON DIP
1 2 3
ON DIP
45
ON DIP
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
88676 7
RD-G2+ DIGITAL REPEATER
Continued from previous page.
INSTAL A IL T ON
16
The EL610D button module needs to be configured in order to assign
a call code to the buttons. Carry out this configuration with the
DIP switch located at the back of the module.
Depending on the configuration option selected, the buttons will be
assigned with a certain call code.
To configure the call code on the monitors. It is worth noting the call
code of each button, as shown in the table below.
IMPORTANT: Only audio installation up to 128 terminals/apartments with EL642 G2+ sound module.
*
( )
Configuring the button code ( 128 / ):up to addresses apartments
EL610D button module
2
Dip1
1
3
Dip2
Dip3
Dip4
Dip5
Dip6
Dip7
Dip8
Module configuration option
P1
1
21
11
DIP switch
On
Off
Off
Off
Off
On
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
Button code
P2 P3 P4 P5 P6 P7
2
22
12
3
23
13
4
24
14
5
25
15
6
26
16
7
27
17
8
28
18
9
29
19
10
30
20
P8 P9 P10 (1)
*
( )
Double button module codes
4 31Off Off Off On Off Off Off On 32 33 34 35 36 37 38 39 40
5 41Off Off Off Off On Off Off On 42 43 44 45 46 47 48 49 50
6 51Off Off Off Off Off On Off On 52 53 54 55 56 57 58 59 60
7 61Off Off Off Off Off Off On On 62 63 64 65 66 67 68 69 70
8 71On Off Off Off Off Off Off Off 72 73 74 75 76 77 78 79 80
9 81Off On Off Off Off Off Off Off 82 83 84 85 86 87 88 89 90
10 91Off Off On Off Off Off Off Off 92 93 94 95 96 97 98 99 100
11 1 10Off Off Off On Off Off Off Off 102103104105106107108109110
12 1 11Off Off Off Off On Off Off Off 112113114115116117118119120
13 Off Off Off Off Off On Off Off 122123124125126127 _ _
Important: Select a different configuration option for each EL610D module..
For description, installation, configuration and programming of the door panel, EL610D module,Important:
monitors and audio terminals, see manual enclosed with the corresponding door panel and monitor.
Note: EL632 G2+ SE V04 & later, setting c d "128" n P1 "127" n P2.module factory with the o e i and i
Note: EL642 G2+ audio module V0 & later, factory setting with the code "128" in P1 & "127" in P2.2
*
( ) Factory setting.
P1- P10: Button 1 - button 10.
(1)
1 12 1 82
RD-G2+ DIGITAL REPEATER
Continued overleaf
INSTAL A IL T ON
17
Important: Select a different configuration option for each EL610D module.
For description, installation, configuration and programming of the door panel, EL610D module,Important:
monitors and audio terminals, see manual enclosed with the corresponding door panel and monitor.
Note: EL642 G2+ audio module V02 & later, factory default with the code "128" in P1.
Nota: audio module V02 & later P1 push button must be changed the call code forEL642 G2+ ,
example in P1 see manual: (p 28“71" , ).agehttps://doc.golmar.es/search/manual/50122528
*
( ) Factory setting.
P1- P10: Pulsador 1 - pulsador 10.
(1)
Note: EL632 G2+ SE video V04 & later, setting c d "128" n P1module factory with the o e i .
Note: EL632 G2+ SE video V04 & later, P1 push button must be changed the call code formodule
example in P1 see manual: (page 28)“71" , .
https://doc.golmar.es/search/manual/50122528
RD-G2+ DIGITAL REPEATER
Continued from previous page.
INSTAL A IL T ON
EL610D button module
Module configuration option
DIP switch Button code
2
Dip1
1
4
6
3
5
7
Dip2
Dip3
Dip4
Dip5
Dip6
Dip7
Dip8
P1
1
11
21
31
6
16
26
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
On
On
On
On
On
On
On
P3 P5 P7 P9
2
12
22
7
17
27
3
13
23
8
18
28
4
14
24
9
19
29
5
15
25
10
20
30
(1)
*
( )
Single button module codes
9
8
11
13
10
12
14
36
46
56
66
41
51
61
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
37
47
57
42
52
62
38
48
58
43
53
63
39
49
59
44
54
64
40
50
60
45
55
65
32 33 34 35
67 68 69 70
18
Configuring double button module codes ( 128 / ):up to addresses apartments
P1P2 P2
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
P1
EL610D
Code 127 Code 128
Code 9
Code 7
Code 5
Code 3
Code 1
Code 19
Code 17
Code 15
Code 13
Code 29
Code 27
Code 25
Code 23
Code 12
Code 127
Cod. 10 Cod. 9
Cod. 8 Cod. 7
Cod. 6 Cod. 5
Cod. 4 Cod. 3
Cod. 2 Cod. 1
Cod. 20 Cod. 19
Cod. 18 Cod. 17
Cod. 16 Cod. 15
Cod. 14 Cod. 13
Cod. 12 Cod. 11
Cod. 30 Cod. 92
Cod. 82 Cod. 72
Cod. 62 Cod. 52
Cod. 42 Cod. 32
Cod. 22 Cod. 12
Front Back
Cod. 1 82
12
ON
2 3 4 5 6 7 8 9 10
NA2
+AP-
C1 NA1 AP+ C2
AP+
GND
BUSBUS
Relé 2Relé 1
_
12Vdc
NC2
CCTV
Code 10
Code 8
Code 6
Code 4
Code 2
Code 20
Code 18
Code 16
Code 14
Code 12
Code 30
Code 28
Code 26
Code 24
Code 22
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
Code 10
Code 8
Code 6
Code 4
Code 2
Code 20
Code 18
Code 16
Code 14
Code 12
Code 30
Code 28
Code 26
Code 24
Code 22
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
Code 11
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
Cod. 1 72
( )
*( )
*
( )
*
Note: EL632 G2+ SE video V04 & later, setting c d "128" n P1 "127" n P2.module factory with the o e i and i
EL642 G2+ audio module V0 & later, factory setting with the code "128" in P1 & "127" in P2.2
( )
*
Monitor Code Monitor CodeMonitor Code
ART 7W/G2+
ART 7H/G2+
ART 4/G2+
ART 7W/G2+
ART 7H/G2+
ART 4/G2+
EL632 G2+ SE
RD-G2+ DIGITAL REPEATER
INSTAL A IL T ON
Continued overleaf
19
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Monitor Code Monitor CodeMonitor Code
Code 40
Code 38
Code 36
Code 34
Code 32
Code 50
Code 48
Code 46
Code 44
Code 42
Code 60
Code 58
Code 56
Code 54
Code 52
Code 70
Code 68
Code 66
Code 64
Code 62
Code 49
Code 47
Code 45
Code 43
Code 14
Code 59
Code 57
Code 55
Code 53
Code 15
Code 69
Code 67
Code 65
Code 63
Code 16
Code 39
Code 37
Code 35
Code 33
Code 13
EL610D
Cod. 50 Cod. 49
Cod. 48 Cod. 47
Cod. 46 Cod. 45
Cod. 44 Cod. 43
Cod. 42 Cod. 14
Cod. 04 Cod. 39
Cod. 38 Cod. 37
Cod. 36 Cod. 35
Cod. 34 Cod. 33
Cod. 32 Cod. 13
Cod. 60 Cod. 95
Cod. 85 Cod. 75
Cod. 65 Cod. 55
Cod. 45 Cod. 35
Cod. 25 Cod. 15
Cod. 70 Cod. 96
Cod. 86 Cod. 76
Cod. 66 Cod. 56
Cod. 46 Cod. 36
Cod. 26 Cod. 16
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
Code 40
Code 38
Code 36
Code 34
Code 32
Code 50
Code 48
Code 46
Code 44
Code 42
Code 60
Code 58
Code 56
Code 54
Code 52
Code 70
Code 68
Code 66
Code 64
Code 62
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
123
ON DIP
4 5 6 7 8
ON DIP
RD-G2+ DIGITAL REPEATER
INSTAL A IL T ON
Continued overleaf
Continued from previous page.
20
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
EL610D
Monitor Code Monitor CodeMonitor Code
Code 80
Code 78
Code 76
Code 74
Code 72
Code 90
Code 88
Code 86
Code 84
Code 28
Code 100
Code 98
Code 96
Code 94
Code 29
Code 110
Code 108
Code 106
Code 104
Code 102
Code 89
Code 87
Code 85
Code 83
Code 18
Code 99
Code 97
Code 95
Code 93
Code 19
Code 109
Code 107
Code 105
Code 103
Code 1 10
Code 79
Code 77
Code 75
Code 73
Code 17
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
Cod. 90 Cod. 98
Cod. 88 Cod. 78
Cod. 68 Cod. 58
Cod. 48 Cod. 38
Cod. 28 Cod. 18
Cod. 08 Cod. 97
Cod. 87 Cod. 77
Cod. 67 Cod. 57
Cod. 47 Cod. 37
Cod. 27 Cod. 17
Cod. 100 Cod. 99
Cod. 89 Cod. 79
Cod. 69 Cod. 59
Cod. 49 Cod. 39
Cod. 29 Cod. 19
Cod. 110 Cod. 910
Cod. 810 Cod. 710
Cod. 106 Cod. 510
Cod. 410 Cod. 310
Cod. 210 Cod. 1 10
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
88
Code 80
Code 78
Code 76
Code 74
Code 72
Code 90
Code 88
Code 86
Code 84
Code 28
Code 100
Code 98
Code 96
Code 94
Code 29
Code 110
Code 108
Code 106
Code 104
Code 102
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
123
ON
4 5 6 7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
RD-G2+ DIGITAL REPEATER
INSTAL A IL T ON
Continued from previous page.
Continued overleaf
Table of contents
Other golmar Repeater manuals
Popular Repeater manuals by other brands
Kenwood
Kenwood NEXEDGE NXR-800 Service manual
rock space
rock space RSD0608 Quick installation guide
Blurex
Blurex Wireless-N quick start guide
Manhattan
Manhattan 525664 user manual
Eminent
Eminent EM4590 R1 manual
Zeta Alarm Systems
Zeta Alarm Systems Premier AL INSTALLATION, COMMISSIONING AND MAINTENANCE with USER INSTRUCTIONS AND GUIDE
