golmar RD-V2PLUS User manual

RD-V2PLUS
Instructions manual
TRD-V2PLUS ML rev.0114
Cód. 50123467
Digital
Repeater

INTRODUCTION
First of all we would like to thank and congratulate you for the purchase of this product manufactured by
The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification
and for the manufacturing of products like this one.
Its advanced technology and exacting quality control will do that customers and users enjoy with the
legion of features this system offers To obtain the maximum profit of these features and a properly wired
installation, we kindly recommend you to expend a few minutes of your time to read this manual.
Golmar.
.
STARTING RECOMMENDATIONS
INDEX
O
O
O
O
O
O
O
The installation and handling of this equipment must be performed by
Install or modify the equipment
Do not use excessive force when tightening the repeater connection block screws
Before connecting the system, check the connections between door panel, repeater, multiplexer,
monitors, telephones and the power supply connection.
When starting the equipment for the first time, or after a modification, the system will remain inactive
for around 45 seconds due to the initial busy channel time
Use Golmar cable in the system
authorised personnel
without the power connected
.
.
.
The entire installation must be at least away from any .
.
.
Do always follow the enclosed information.
O
40 cm. other installation
RAP-2150 V2Plus
Introduction........................................................................................................................41
Index .................................................................................................................................41
Starting recommendations....................................................................................................41
Safety precautions ...............................................................................................................42
System characteristics ..........................................................................................................42
Operation modes ..........................................................................................................43-46
Description of the repeater....................................................................................................47
Installation of the repeater ....................................................................................................47
.............................................................................................................48
.....................................................................................................................49
.............................................................................................49-50
.................................................................................................
.......................................50
....................................51
Installation diagrams ...............................................................................................................
Video door entry system without distributor and 1 repeater ......................................................52
.................................53-54
..55-56
Special connections ......................................................................................................57-58
Replacement
Minimum requirements
Installation of replacement
Cable, sections and distances chart (one access and one riser)
Cable, sections and distances chart (several accesses and risers)
Video door entry system with distributor and 2 repeaters in daisy chain
Video door entry system with several accesses, risers, distributors and 2 repeaters in daisy chain
Autodiagnostic Leds
2

SAFETY PRECAUTIONS
O
O
O
O
O
O
O
O
Install or modify the equipment .
The installation and handling of these equipments must be performed by .
The entire installation must be at least away from any .
Do not use excessive force when tightening the connector screws.
Install the unit in a dry and protected place without risk of drip or water projections.
Avoid to place it near to heating sources, dusty locations, humid or smoky enviroments.
Do not block ventilation holes of the unit so that air can circulate freely.
To avoid damage, the repeater has to be firmly fixed.
without the power connected
authorised personnel
40 cm. other installation
SYSTEM CHARACTERISTICS
O
w
w
w
O
w
w
O
O
O
O
O
O
In installations with 2 repeaters in daisy chain and 1 multiplexer the distances will be:
The repeater will increase the distance in 150 meters more.
Up to 2 digital repeaters connected in daisy chain.
Maximum distance between the power supply and digital repeater: 3 m., with a wire section of 1,5 mm.
Autodiagnostic leds showing the Bus status (in the riser where repeater is installed) and the power
supply status of the repeater.
The monitor must be the version or later, for its compatibility with the
repeater.
Use Golmar cable in the .
Tekna V2Plus Color V.02
RAP-2150 V2Plus system
Digital repeater for system a :
It increases the distance in 200 meters more.
In daisy chain installations (without distributors), it increases 16 monitors/telephones in a maximum
distance of 150 meters between the repeater and the last monitor/telephone and between
monitors/telephones of the different apartments (connected to repeater).
It increases 32 monitors/telephones in a maximum distance of 150 meters between the repeater
and the last monitor/telephone and between monitors/telephones of the different apartments
(connected to repeater).
In daisy chain installations (without distributors), it increases 16 monitors/telephones in a maximum
distance of 100 meters between the repeater and the last monitor/telephone and between
monitors/telephones of the different apartments (connected to repeater).
It increases 32 monitors/telephones in a maximum distance of 100 meters between the repeater
and the last monitor/telephone and between monitors/telephones of the different apartments
(connected to repeater).
V2Plus
w
llows one of these functions at once
IMPORTANT: In the output of a .distributor cannot be connected another distributor
2
3

4
OPERATION MODES
V2Plus system with 1 access door panel (1 riser).
Installations with 1 access door panel and up to 2 repeaters in daisy chain where it is wanted to increase the
distance with the repeater in 200 m. more (see example A & C) or increase up to 32 monitors/telephones in a
max. distance of 150 m. between the repeater and the last monitor/telephone and between monitors/telephones
of different apartments connected to repeater (see example B, C & D). Important: Read the footnotes.
A: 32 elements (350 meters):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
FA-V2Plus
150m
25m.
0,75 mm
2
200m
3m.
1,5 mm
2
2 2
B: 64 elements (300 meters):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
150m
25m.
0,75 mm
2
150m
2
BUS
FA-V2Plus
3m.
1,5 mm
22
C: Repeater (64 elements / 500 meters):in daisy chain
EL500/V2Plus
FA-V2Plus
RD-V2Plus
150m
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
RD-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
150m
Bus: Golmar RAP-2150 cable.
BUS BUS
BUS BUS
*
*
*
Important: Do not exceed the max. monitors/telephones connected to a door panel/multiplexer/repeater, or the distances
indicated for door panel/multiplexer/repeater and last monitor and monitors between different apartments connected to door
panel/multiplexer/repeater. For characteristics, sections and distances see the corresponding product manual.
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
( )
1
( )
1( ) 1
( )
1( ) 1
Note: If the repeater/multiplexer is at a distance less than 50 meters from the door panel, place in the door panel the dip
gain SW1-6 to OFF.
( )
1

OPERATION MODES
V2Plus system with several accesses and risers.
Installations with several access door panel, 1 multiplexer and up to 2 repeaters in daisy chain where it is
wanted to increase the distance with the repeater in 200 m. more (see exemple A & B) or increase up to
32 monitors/telephones in a max. distance of 150 m. between the repeater and the last
monitor/telephone and between monitors/telephones of different apartments connected to repeater
(see example A, B, & C). Installations
monitors/telephones of different
apartments connected to repeater
with 2 repeaters in daisy chain and 1 multiplexer, the repeater will
increase the distance in 150 m. more or up to 32 monitors/telephones in a max. distance of 100 m.
between the repeater and the last monitor/telephone and between
(see example D-H). Important: Read the footnotes on page 45.
A: 32 elements for riser (550 meters):
B: 32 elements for riser (550 meters):
C: 64 elements for riser (500 meters):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
150m
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
150m
Bus: Golmar RAP-2150 cable.
D: Repeater in daisy chain (32 elements for riser / 600 meters):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
MC-V2Plus
150m
25m.
0,75 mm
2
200m
2
BUS
FA-V2Plus
3m.
1,5 mm
22
200m
BUS BUS
FA-V2Plus
3m.
1,5 mm
22
EL500/V2Plus
FA-V2Plus
RD-V2Plus MC-V2Plus
150m
25m.
0,75 mm
2
200m
2
BUS
FA-V2Plus
3m.
1,5 mm
22
200m
BUS BUS
FA-V2Plus
3m.
1,5 mm
22
EL500/V2Plus
FA-V2Plus
RD-V2Plus
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
100m
RD-V2Plus
FA-V2Plus
3m.
1,5 mm
22
150m 150m
Continue
*
*
*
*
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
( )
1
( )
1
( )
1
( )
1
( )
1
5

OPERATION MODES
F: (32 elements for riser / 600 meters):Repeater in daisy chain
G: (64 elements for riser / 550 meters):Repeater in daisy chain
E: Repeater in daisy chain (32 elements for riser / 600 meters):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
100m
RD-V2Plus
FA-V2Plus
3m.
1,5 mm
22
150m 150m
EL500/V2Plus
FA-V2Plus
RD-V2Plus
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
100m
RD-V2Plus
FA-V2Plus
3m.
1,5 mm
22
150m 150m
EL500/V2Plus
FA-V2Plus
25m.
0,75 mm2
23m.
1,5 mm2
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS BUS
100m
RD-V2Plus
FA-V2Plus
2
BUS
200m 100m
RD-V2Plus
FA-V2Plus
3m.
1,5 mm
22
150m
Coming from previous page
*
*
*
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
Bus: Golmar RAP-2150 cable.
*
Important: Do not exceed the max. monitors/telephones connected to a door panel/multiplexer/repeater, or the distances
indicated for door panel/multiplexer/repeater and last monitor and monitors between different apartments connected to door
panel/multiplexer/repeater. For characteristics, sections and distances see the corresponding product manual.
Note: If the repeater/multiplexer is at a distance less than 50 meters from the door panel, place in the door panel the dip
gain SW1-6 to OFF.
( )
1
( )
1( ) 1
( )
1
( )
1
6

OPERATION MODES
The Repeater will be connected in the distributed output of D1L-V2Plus or D4L-V2Plus distributor and can
increase the distance at 100 meters between the door panel and the repeater/s or most distant points of
the bus between the door panel and the repeater/s. Important: Read the notes that are detailed below:
Special connection '1': (Door panel + Distributor + Repeater + Monitors).
A: Up to 32 ele. for distributed output and up to 128 ele. for D4L-V2Plus :distributor
A: Up to 128 ele. for riser and up to 512 ele. for multiplexer):
EL500/V2Plus
FA-V2Plus
RD-V2Plus
100m
25m.
0,75 mm
2
200m
2
FA-V2Plus
3m.
1,5 mm
22
MC-V2Plus
FA-V2Plus
3m.
1,5 mm
22
BUS BUS BUS
150m
Bus: Golmar RAP-2150 cable.
Distributed output: Golmar RAP-2150 cable.
EL500/V2Plus
FA-V2Plus
RD-V2Plus
D4L-V2Plus
150m
25m.
0,75 mm
2
100m
2
BUS D1L or D4L-V2Plus
Up to 32 monitors
Apartments
FA-V2Plus
3m.
1,5 mm
22
Sal. Dist.
BUS
D4L-V2Plus
Sal. Dist.
Special connection '2': (Door panel + Multiplexer + Distributor + Repeater + Monitors).
Up to 1 RD-V2Plus for each distributed output of D1L or D4L-V2Plus distributor.
For this operation mode contact our technical support department.
The Repeater will be connected in the distributed output of D1L-V2Plus or D4L-V2Plus distributor and
can increase the distance at 100 meters between the multiplexer and the repeater or most distant points
of the bus between the multiplexer and the repeater. Important: Read the notes that are detailed below:
*
*
Bus: Golmar RAP-2150 cable.
Distributed output: Golmar RAP-2150 cable.
Up to 1 RD-V2Plus for each distributed output of D1L or D4L-V2Plus distributor.
For this operation mode contact our technical support department.
(2)
(2)
(2)
(2)
D1L or D4L-V2Plus
Up to 32 monitors
Apartments
*
Important: Do not exceed the max. monitors/telephones connected to a door panel/multiplexer/repeater, or the distances
indicated for door panel/multiplexer/repeater and last monitor and monitors between different apartments connected to door
panel/multiplexer/repeater. For characteristics, sections and distances see the corresponding product manual.
Note: If the repeater/multiplexer is at a distance less than 50 meters from the door panel, place in the door panel the dip
gain SW1-6 to OFF.
( )
1
*
Important: Do not exceed the max. monitors/telephones connected to a door panel/multiplexer/repeater, or the distances
indicated for door panel/multiplexer/repeater and last monitor and monitors between different apartments connected to door
panel/multiplexer/repeater. For characteristics, sections and distances see the corresponding product manual.
Note: If the repeater/multiplexer is at a distance less than 50 meters from the door panel, place in the door panel the dip
gain SW1-6 to OFF.
( )
1
( )
1
( )
1
7

INSTALLATION
Detail of the repeater installation.
The can be installed on a DIN guide
(6 elements), pressing it lightly.
To extract the from the DIN guide,
use a plain screwdriver to lever the flange as
shown in the picture.
repeater
repeater
Install the in a dry and protected place without risk of drip or water projections.
To avoid damage, the must be firmly fixed.
repeater
repeater
To install the directly on the wall, drill two holes
of 6mm. and insert the wallplugs. Fix the
with the specified screws.
repeater
repeater
Description of the repeater.
The installation or modification the
performed
repeater,
repeater
must be
.
The installation and handling of the must be
performed by
in the absence of electrical current
authorized personnel.
DESCRIPTION
DIN 46277
Autodiagnostic LEDs.
Power supply input
(with FA-V2Plus power supply).
Label.
DIN rail latch release.
Bus .connection block
Reset button 'P1', for short-circuit Bus
(riser where repeater is connected).
8

AUTODIAGNOSTIC LEDS
Description of autodiagnostic LEDs.
The autodiagnostics LEDs are placed on the top right
of the digital repeater.
Red Led
Fixed: P .ower supply connected
If the short circuit is eliminated before
2 minutes (approx.), the repeater will
automatically reset. Past this time it
will be necessary to press button 'P1'
to restart the repeater.
(See description page 47).
Green Led
Fixed: Correct operation.
Blinking: Riser communicating.
: Riser not functioning due to a short-circuit in the
riser * between the bus wires.
Off
OFF: Power supply disconnected.
*
9

REPLACEMENT
The Golmar video door entry system is a digital system with simplified installation (2 wire bus
without polarity), designed to new installations and to replace existing audio door entry systems in both
apartment blocks and villas.
In installation for replacement it is necessary a detailed study of the existing installation before installing
the system. To check that your installation complies with the systems minimum recommended
requirements, please read carefully the following chapters, which provide details of the checks to be done.
V2PLUS
'
Before installing this system, we must ensure that the existing installation complies with the following
requirements:
-All branch connections must be made using D4L-V2PLUS or D1L-V2PLUS distributors.
-Each floor must have physical space to situate the distributor/s, in case they are necessary.
-Each apartment must have sufficient space to install the video system monitor.
-Maximum installation distance it will depend on the section and the installed cable (see pages 50-51).
-Installations with independent more common wires, (separate and do not
connect the independent ones).
-1 access door panel, (up to 3 access door panel with multiplexer).
-Up to 32 (monitors, telephones or call repeaters) and apartments without using converters, repeaters
or multiplexers.
-Up to 16 (monitors, telephones or call repeaters) and apartments in daisy chain installations without
distributor, per installation without using converters, repeaters or multiplexers.
-Up to 3 elements (monitors, telephones or call repeaters S-45) per apartment.
-Installations with more than 32 elements or it is wanted to increase the distance in the riser (it needs the
use of the ).
-Installations with more than 32 elements or 1 riser (it needs the use of the multiplexer ).
-Installations with general door panels (it needs the use of the converters).
-Before connecting the systems power supply, we must ensure that there are
If so, we must disconnect them or replace them with
units that are compatible with the new system, otherwise the installation could be seriously
damaged or burnt.
If any of the first three requirements are not met, it will be necessary to replace the installation riser.
If the branch connections to the apartments are in good condition, their replacement will not be necessary.
If replacing the installation riser, use the Golmar cable and the next sections:
-The installation must be realized by multipaired cable, (not to use single-wire cables).
-The wires must not be spliced, frayed, nor touch metal parts, and must not vary in cross
section throughout the entire installation.
-The entire installation must be at least 40cm away from any other installation otherwise there
is a risk that the audio and video signal be exposed to interference, or that the system
does not work correctly.
only use the common wires
NO old parallel units,
relays or call repeaters in the apartments.
MC-V2PLUS
RD-V2PLUS
MC-V2PLUS
CD-V2PLUS
RAP-2150
'
RAP-2150
Terminal
SECTIONS CHART
150m.
Door panel-Monitor P
.S.- Door panel
+, -
BUS, D
50m.
Door panel - CV
50m.
1,5mm²
CV1,CV2 0,5mm²
(d.c lock release)
CV1,CV2, ~, ~ 1mm²
(a.c lock release) 1mm²
*
One access and one riser
MINIMUM REQUIREMENTS
Continue.
*
*
( )
1
Do not use different types of cable in the same installation .(contact with our technical support department)
Maximum distance of 150 m. between door panel and last monitor/telephone and between
monitors/telephones of different apartments connected to door panel.
( )
2
( )
2
0
1

Compatibility of cables and sections.
Monitor V2Plus
Max. 32 apartments
FA-V2PLUS
Door panel-V2PLUS
P
dB
dC
dA
Monitor V2Plus
One access and one riser (without multiplexer)
Cables and sections
10m.
dA
1mm (twisted).
0,5mm (twisted).
1,5mm (twisted).
0,18mm (multipaired).
Rap-2150 1mm (twisted).
2 par UTP Cat 5 0,18x2= 0,36mm.
4 par UTP Cat 5 0,18x4= 0,72mm.
Cables and distances chart
dB+dC dC
0,25mm (twisted).
0,18x2= 0,36mm (multipaired).
0,18x4= 0,72mm .(multipaired)
1 par UTP Cat 5 0,18mm.
2
2
2
2
2
2
2
2
2
2
2
20m.
40m.
50m.
5m.
10m.
25m.
40m.
5m.
10m.
25m.
40m.
70m.
100m.
100m.
25m.
50m.
100m.
150m.
25m.
50m.
100m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
*
*Use Golmar RAP-2150 cable, for new installations.
IMPORTANT
RAP-2150
:
if the installation includes multiplexers in daisy chain with monitors B/W:
- Maximum distance between door panel/converter and multiplexer:150m.
- Maximum distance between multiplexer in daisy chain and the last monitor B/W and between monitors
of different apartments (in the same riser) connected to multiplexer in daisy chain will be:100m.
Golmar has a special cable for this system, its reference number is . The use of this cable
ensures the correct functioning of the system and simplifies the riser replacement given that it contains
all the necessary wires for the installation.
RAP-2150
Terminal
SECTIONS CHART
200m.
Door panel-Multiplexer P.S.- Door panel
+, -
BUS, D
50m.
1,5mm²
CV1,CV2
(d.c lock release)
CV1,CV2, ~, ~
(a.c lock release) 1mm²
50m.
Door panel-CV
0,5mm²
1mm²
RAP-2150
150m.
Multiplexer-Monitor
Several accesses and risers
INSTALLATION OF REPLACEMENT
MINIMUM REQUIREMENTS
Coming from previous page
Continue.
( )
1( ) 1
( )
1
( )
3
Maximum distance of 150 meters between multiplexer and last monitor/telephone and between
monitors/telephones of different apartments (in the same riser) connected to multiplexer.
( )
3
IMPORTANT repeater
(C
: The distance to increase with , it will depend on the installed cable section.
. See examples of installation diagrams,)pages 52-54 and 57.
ontact our technical support department
1
1

M -C V2PLUS
MC-V2PLUS
daisy chain
FA-V2PLUS
dF=3m./1,5mm
M -C V2PLUS
MC-V2PLUS
Monitor V2Plus
Max. 32 apartments
FA-V2PLUS
Door panel-V2PLUS
P
dC
dD
dA
Monitor V2Plus
dB
FA-V2PLUS
Cables and distances chart
*Use Golmar RAP-2150 cable, for new installations.
Several accesses and risers (with multiplexers)
M -C V2PLUS
MC-V2PLUS
Max. 32 apartments
FA-V2PLUS
Door panel-V2PLUS
P
dC’
dD
dA
Monitor
V2Plus B/W
FA-V2PLUS
Monitor
V2Plus B/W
dB’
Installation with multiplexer Installation with multiplexers
in daisy chain and monitors B/W
INSTALLATION OF REPLACEMENT
Riser 1
Riser 1
See operation modes, configuration, programming and installation in the TMC-V2PLUSML instructions manual.
Coming from previous page
2
dF=3m./1,5mm2
dF=3m./1,5mm2
IMPORTANT repeater
(C
: The distance to increase with , it will depend on the installed cable section.
. See examples of installation diagrams,)page 55-56 and 58.ontact our technical support department
Cables y secciones
10m.
dA
1mm (trenzado).
0,5mm (trenzado).
1,5mm (trenzado).
0,18mm (multipar).
Rap-2150 1mm (trenzado).
2 par UTP Cat 5 0,18x2= 0,36mm
4 par UTP Cat 5 0,18x4= 0,72mm
dDdB dC’+dD
0,25mm (trenzado).
0,18x2= 0,36mm (multipar).
0,18x4= 0,72mm (multipar).
1 par UTP Cat 5 0,18mm
2
2
2
2
2
2
2
2
2
2
2
20m.
40m.
50m.
5m.
10m.
25m.
40m.
5m.
10m.
25m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
15m.
50m.
100m.
100m.
150m.
35m.
70m.
100m.
200m.
35m.
70m.
100m.
26m.
46m.
67m.
67m.
16m.
33m.
67m.
100m.
16m.
33m.
67m.
dC+dD
40m.
70m.
100m.
100m.
25m.
50m.
100m.
150m.
25m.
50m.
100m.
dB’
37m.
75m.
75m.
112m.
26m.
52m.
75m.
150m.
26m.
52m.
75m.
*
dE
26m.
46m.
67m.
67m.
16m.
33m.
67m.
100m.
16m.
33m.
67m.
( )
1
( )
1
dE
( )
1
The distances indicated for 'dE' in the chart, it must be with the multiplexer ó later; previous versions
(distance=3m).
V
.02
2
1

INSTALLATION DIAGRAMS
BUS IN PA PB BUS OUT HZ
Tekna V2Plus
BUS IN PA PB
BUS OUT HZ
Tekna V2Plus
Sw2
Sw2
Configuring the end of
line in the last monitor.
*
*
SEC
PRI
+0
110230
- -
+
Main
V2Plus door panel
SW1
6
CV1+12 CV2
BUS
BUS IN BUS OUT
RD-V2Plus
SEC
PRI
+0110230
FA-V2PLUS
- -
+
Main
FA-V2PLUS
Daisy chain installation for Video door entry system without distributor, 1 repeater & d.c lock release.
IMPORTANT: To configure and to program each equipment see the appropiate instruction book.
See example 'A' and important notes in 'operation modes' (page 43).
REMEMBER: The total number of daisy chain elements (monitors/telephones) installed for each
repeater must never exceed 16 units.
M
M =Master.
(1)
(1)
(1)
(1)
3
1

D3
BUS IN PA PB BUS OUT HZ
F.Linea
Insert a 120 ohm end
of line resistor in the
last distributor.
*
D4L-V2Plus
BUS IN PA PB BUS OUT HZ
BUSD2D1 BUS D4
D3
F.Linea
BUSD2D1 BUS D4
BUS IN PA PB BUS OUT HZ
BUS IN PA PB BUS OUT HZ
*
R.120W
D4L-V2Plus
Configuring the end of
line in the last monitor.
Sw2
Sw2
Sw2
Sw2
**
****
****
BUS IN BUS OUT
RD-V2Plus
SEC
PRI
+0110230
FA-V2PLUS
- -
+
Main
BUS IN BUS OUT
RD-V2Plus
SEC
PRI
+0110230
FA-V2PLUS
- -
+
Main
IMPORTANT: To configure and to program each equipment see the appropiate instruction book.
(1)
(1)(1)
(1)(1)
Tekna V2Plus
Tekna V2Plus
Tekna V2Plus
Tekna V2Plus
4
1

INSTALLATION DIAGRAMS
See example 'C' and important notes in 'operation modes' (pág. 43).
The installation diagram shows the connection of a video door entry system with one door panel to
access the building and d.c lock release.with distributors, 2 repeaters in daisy chain
REMEMBER: Installations with distributors, the total number of elements (monitors/telephones)
installed for each repeater must never exceed 32 units.
Video door entry system with distributor, 2 repeaters and d.c lock release.
SEC
PRI
+0110230
FA-V2PLUS
- -
+
Main
V2Plus door panel
CV1+12 CV2
SW1
6
BUS
M
M =Master.
(1)
5
1

Riser 1
D3
BUS IN PA PB BUS OUT HZ
F.Linea
BUS IN PA PB BUS OUT HZ
BUSD2D1 BUS D4
Tekna V2Plus
Sw2
**
D4L-V2Plus
*
M -C V2PLUS
+COL 1
-
COL 2 COL 3 COL 4 PL 1 PL 2 PL 3
MC-V2PLUS
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
BUS IN PA PB BUS OUT HZ
Tekna V2Plus
Sw2
**
Riser 2
Tekna V2Plus
Sw2
**
R.120W
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
See example 'F' and important notes in 'operation modes' (page 45).
The installation diagram shows the connection of a video door entry system with several door panel
to access the building
and d.c lock release.
and risers with distributors, 2 repeaters in daisy chain (1 between door
panel and the multiplexer and the other one in each riser of the multiplexer)
IMPORTANT: To configure and to program each equipment see the appropiate instruction book.
(1)
(1) (1) (1)
61

INSTALLATION DIAGRAMS
BUS IN PA PB BUS OUT HZ
BUS BUSD
F.Linea
D1L-V2Plus
Riser 3
*
*
Tekna V2Plus
Sw2
*
BUS IN PA PB BUS OUT HZ
BUS BUSD
F.Linea
D1L-V2Plus
Riser 4
*
*
Tekna V2Plus
Sw2
*
SEC
PRI
+0110230
FA-V2PLUS
- -
+
Main
CV1+12 CV2
BUS
FA-V2PLUS
SEC
PRI
+0110230
- -
+
Main
CV1+12 CV2
BUS
SW1 SW1
6
R.120WR.120W
S
M
*
**
Insert a 120 ohm end
of line resistor in the
last distributor.
Configuring the end of
line in the last monitor.
M =Master.
S =Slave.
V2Plus door panelV2Plus door panel
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
Next door panel.
Video door entry system with distributors, several accesses and risers, 2 repeaters and d.c lock release.
(1) (1)
(1)(1)
71

INSTALLATION DIAGRAMS
Special connection 1: Door panel with 4 lines distributor, repeater and d.c lock release.
See special connection '1' example 'A' and important notes in 'operation modes' (pág. 46).
The installation diagram shows the connection of a video door entry system with 1
and d.c lock release.
distributor of 4 lines, 1
repeater for each distributed output of D4L-V2Plus distributor
D3
F.Linea
Insert a 120 ohm end of line
resistor in the las distributor.
D4L-V2Plus
BUSD2D1 BUS D4
Configuring the end of
line in the last monitor.
V2Plus door panel
CV1+12 CV2
SW1
6
**
BUS
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
D1L-V2Plus
BUS IN PA PB
BUS OUT HZ
BUS BUSD
F.Linea
*
R.120W
Sw2
**
BUS IN BUS OUT
SEC
PRI
+0110230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
D1L-V2Plus
BUS IN PA PB
BUS OUT HZ
BUS BUSD
F.Linea
*
R.120W
Sw2
**
*
R.120W
SEC
PRI
+0
110230
- -
+
Main
FA-V2PLUS
M
M =Master.
*
Riser 1 Riser 4
To riser 2 To riser 3
IMPORTANT: To configure and to program each equipment see the appropiate instruction book.
(1)
(1) (1)
(1)
Tekna V2PlusTekna V2Plus
81

INSTALLATION DIAGRAMS
Special connexion 2: Door panel with multiplexer, 4 lines distributor, repeater and d.c lock release.
See special connexion '2' example 'A' and important notes in 'operation modes' (page 46).
The installation diagram shows the connection of a video door entry system with
and d.c
lock release.
1 multiplexer, 1 D4L-
V2Plus distributor of 4 lines, 1 repeater for each distributed output of D4L-V2Plus distributor
D3
F.Linea
Insert a 120 ohm end of line
resistor in the last distributor.
D4L-V2Plus
BUSD2D1 BUS D4
Configuring the end of
line in the las monitor.
V2Plus door panel
CV1+12 CV2
SW1
6
**
BUS
BUS IN BUS OUT
SEC
PRI
+0110
230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
D1L-V2Plus
BUS IN PA PB
BUS OUT HZ
BUS BUSD
F.Linea
*
R.120W
Sw2
**
BUS IN BUS OUT
SEC
PRI
+0110
230
- -
+
Main
FA-V2PLUS
RD-V2PLUS
D1L-V2Plus
BUS IN PA PB
BUS OUT HZ
BUS BUSD
F.Linea
*
R.120W
Sw2
**
*
R.120W
M
M -C V2PLUS
+COL 1
-
COL 2 COL 3 COL 4 PL 1 PL 2 PL 3
MC-V2PLUS
SEC
PRI
+0110230
- -
+
Red
FA-V2PLUS
M =Master.
*
Riser 1 Riser 4
To riser 2 To riser 3
SEC
PRI
+0110
230
- -
+
Main
FA-V2PLUS
Backbone 1
To next D4L-V2Plus
Distributor
IMPORTANT: To configure and to program each equipment see the appropiate instruction book.
(1)
(1)
(1) (1)
Tekna V2PlusTekna V2Plus
19

1095 Budapest, Mester utca 34.
Tel.: *218-5542, 215-9771, 215-7550,
216-7017, 216-7018 Fax: [phone]
Mobil: 30 940-1970, 30 959-0930
E-mail: [email protected] Web: www.delton.hu
www.golmar.hu
1141 Budapest, Fogarasi út 77.
Tel.: *220-7940, 220-7814, 220-7959,
220-8881, 364-3428 Fax: [phone]
Mobil: 30 531-5454, 30 939-9989