Gomax MA-5544V User manual

MA-5544V
4K-HDR 4x4 HDBaseT Lite matrix with PoC
User Manual
rev: 200511
Made in Taiwan
TABLE OF CONTENTS
INTRODUCTION ................................................................................................................1
FEATURES.........................................................................................................................1
PACKAGE CONTENTS......................................................................................................2
SPECIFICATIONS..............................................................................................................3
CONNECTION DIAGRAM ..................................................................................................4
PANEL DESCRIPTIONS ....................................................................................................5
IR PASS-THROUGH...........................................................................................................6
OPERATION APPROACH..................................................................................................7
EDID LEARNING..............................................................................................................22
FAQ..................................................................................................................................23
NOTICE............................................................................................................................24
WARRANTY.....................................................................................................................25

-1-
INTRODUCTION
The MA-5544V 4K-HDR 4x4 HDBaseT Lite matrix with PoC provides the most flexible and cost
effective solution in the market to route high definition video sources plus multi-channel (up to 7.1-
channel) digital audio from any of the four HDMI sources to the remote displays at the same time. MA-
5544V supports all 3D formats, the true 4K 2K video and provides one HDMI local loopout. Through only
one low cost Cat-5/5e/6 LAN cables, not only high quality video and audio can be transmitted to the
display sites, but also users can switch among four HDMI sources using the push button, IR remote, RS-
232, IP control, web-interface control, cloud, control 4 & Alexsa Echo control. Furthermore, the built-in
IR extension function makes users at display site access the DVD player, PS4 or any HDMI supported
devices directly! In addition, MA-5544V also supports PoC (Power over Cable) which can power RX unit
from TX side with power supply.
FEATURES
HDMI 2.0a compliant
Supports 4K2K@60 4:4:4 8bits
Supports HDR1, which is 4K2K@60 4:2:0 10bits2
Extends HDMI signal up to 60m (198ft) from the HDMI source at Full HD 1080p 36-bit, 35m (114ft) at
4K2K@60 444 (4K-HDR Technology)
Supports PoC(Power over Cable) which can power RX unit from TX side with power supply
Supports one HDMI loopout
Supports audio extraction via stereo audio L/R & S/PDIF from HDMI loopout
HDCP1.4 & HDCP2.2 compliant
Supports resolution downscaling from 4K2K to 1080P3
Bi-directional IR pass-though
Allows controlling local HDMI sources or display through control path
Allows controlling matrix switcher from IR remote
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission
Allows any source to be displayed on multiple displays at the same time
Allows any HDMI display to view any HDMI source at any time
Supports 7.1 channel digital audio
Supports default HDMI EDID and learns the EDID of displays to matrix switcher
The matrix switcher can switch every output channels from any HDMI inputs by Push button, IR
remote control, RS-232, IP control, web-interface control, cloud, control 4 & Alexsa Echo control.
Easy installation with rack-mounting
Fast response time –6~8 seconds for channel switch
-2-
PACKAGE CONTENTS
1x MA-5544V
1x IR receiver
1x DC 5V 4A
1x IR Remote control*
1x Rack-mounting ear set
1x Installation software CD
1x User Manual
1. HDR = High Dynamic Range.
2. The video bandwidth of 4K2K@60 4:2:0 10bits (HDR) is 384 MHz, and the 4K2K@60 4:4:4
8bits is 594MHz.
3. When used in conjunction with the EX-57VAC-I-SP-RX receiver
(a) The MA-5544V can support resolution downscaling from 4K2K to 1080P
(b) NOT supports resolution downscaling from 4K2K@60 4:2:2 to 1080P
Additional IR remote controllers and IR blasters can be purchased as optional accessories to
control the HDMI sources located separately.
!
*
!
The length depends on the characteristics and quality of the cables. Higher resolutions and
longer transmission distances require low skew cables (<25ns/100m) for best performance.
Unshielded CAT6 with metal RJ45 connectors is recommended.
!

-3-
SPECIFICATIONS
Model Name
MA-5544V
Technical
Role of usage
True 4x4 matrix switcher
Transmitter [TX]
HDMI compliance
HDMI 2.0a
HDCP compliance
Yes
Video bandwidth
Single-link 600MHz [18Gbps]
Video support
HDR 4K2K@60(4:2:0 10bits) / 4K2K@60 (4:4:4 8bits)
Audio support
Surround sound (up to 7.1ch) or stereo digital audio
PoC support
YES
HDMI over UTP
transmission range
1080p@60 –up to 60m (198ft) [CAT.X]
4K2K@60 444 (4K-HDR Technology) –35m (114ft)
Input TMDS signal
1.2 Volts [peak-to-peak]
Input DDC signal
5 Volts [peak-to-peak, TTL]
ESD protection
Human body model —±15kV [air-gap discharge] & ±8kV [contact discharge]
PCB stack-up
4-layer board [impedance control —differential 100Ω; single 50Ω]
Input
4x HDMI / 1x RS-232 / 1x RJ-45 for IP Control / 5x IR socket for IR receiver
Output
4x RJ-45(HDBaseT) / 1x HDMI / 1x RCA / 5x IR socket for IR blaster
HDMI Input selection
Push button / IR remote control / RS-232 control / IP control / web-
interface control/ cloud / control 4 & Alexsa Echo control
HDMI source control
Controllable via IR pass-through from IR receiver at RX to IR blaster at TX
IR remote control
Electro-optical characteristics: = 25°/ Carrier frequency: 38kHz
HDMI connector
Type A [19-pin female]
RJ-45 connector
WE/SS 8P8C(Reverse Mode)
RS-232 connector
DE-9 [9-pin D-sub female]
3.5mm connector
1. Earphone jack for IR blaster
[All IR Out] IR signal from all outputs
[IR1~IR4] IR control on individual source device
2. Earphone jack for IR receiver
[System IR] Receives IR commands from remote control
[IR1~IR4] Receives IR commands from individual remote control
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model
440 x 228 x 44mm [1'4" x 8.9" x 1.7"]
Package
526 x 318 x 156mm [1'7" x 12.5" x 6.1"]
Carton
543 x 335 x 344mm [1'8" x 13.2" x 1'1"]
Weight
Model
2548g [5.6 lbs]
Package
3833g [8.4lbs]
-4-
Fixedness
Wall-mounting case
Power supply
12V 7.5A DC
Power consumption
70 Watt [max]
Operation temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]
CONNECTION DIAGRAM

-5-
PANEL DESCRIPTIONS
1. Power Switch
2. Source Status: Input source indicator LED
3. Display Status: Output display indicator LED
4. IR SENSOR: IR sensor for receiving the IR commands from IR remote
5. Output Push Button & 7-segment LED: Front panel push buttons used to select the number of display
channel & LED display for output ports
6. Input Push Button & 7-segment LED: Front panel push buttons used to select the number of input
source & LED display for input channels
7. IR Receiver 1-4: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
8. RS-232: RS-232 control port
9. All IR Output: 3.5mm IR blaster socket for HDMI source control on all 4 inputs
10.System IR Receiver: Ext. IR receiver
11. INPUT 1-4: HDMI inputs
12.IR Blaster 1-4: 3.5mm IR blaster socket for individual HDMI source control
13.RJ-45: HDBT output port 1-4
14.S/PDIF output: Audio extraction from HDMI local loopout port 1
15.Stereo Audio Output L/R: Audio extraction from HDMI local loopout port 1
16.HDMI Local Loopout Port 1: Local HDMI loopout from HDBT output port 4
17.Ethernet: Ethernet control port
18.+12V DC: 12V DC power jack
-6-
IR PASS-THROUGH
[IR Extenders]
IR Blaster
IR Receiver
[IR Sockets]
MA-5544V
All IR Out: The default location for IR blaster to transmit all IR command signals received from any of
the one remote receivers to all of the HDMI sources.
IR BLASTER 1-4: IR blaster connected here can only transmit IR command signals from the remote
receivers that are setting at respective input channel from 1 to 4.
System IR: Receives IR commands from remote control
IR RECEIVER 1-4: Receives IR commands from individual remote control
[Definition of IR Earphone Jack]
IR Blaster
IR Receiver

You can buy any IR extension cables in the market that are compatible to the definition of the
IR sockets for the extender if necessary for replacement use. However, IR cables longer than
2m (6-ft) may not work.
Incorrect placement of IR Blaster and Receiver may result in the failure of the
IR extenders. Please check carefully before plugging in the IR extender to the
respective IR sockets. Warranty will not cover the damage.
CAUTION!

-7-
OPERATION APPROACH
Method A: Push-in Button
IN/OUT MAP
(1) Use the “+” or “-“ output push button to select the number of display
(2) Use the “+” or “-“ input push button to select the number of input source
“+”: change selected input/output port in ascending order
“-”: change selected input/output port in descending order
After you select the desired input/output port, the LED will blink twice and the setting will be effective
Method B: IR Remote Control
Button
Function
OFF
Standby mode
ON
Power on the matrix switcher
MUTE
Turn off output’s video and audio
STATUS
Preset output status
SAVE
Save current mapping mode
PRESET
Preset mapping mode
DEFAULT EDID
Begin default EDID selection
LEARN EDID
Begin EDID learning from one output
CLEAR
Clear the previous IR operation procedure
TAKE
Trigger the previous setting
F1
Reserved
F2
Reserved
1. IN/OUT Switch
Operation
Procedure
7-Segment LED
IN/OUT Switch
Push the button on the checkerboard
to select input & output port
Ex: Input 2
To Output 3
Push the red circle button as below to
select input 2 to output 3
3
2
-8-
2. Example of function key
Operation
Procedure
7-Segment LED
Output Status
Status + A~D(Output 1~4) + Clear
Ex: Output 4
(Input 2)
1.Press “STATUS” button
-
-
2.Press number key “D” to select Output 4
4
3.Press “CLEAR” button
Save Current Mapping
Save + A~H(1-8 storage site) + Take
Ex: Save current
mapping to 5
1.Press “SAVE” button
d
-
2.Press number key “E” to select the storage site 5
d
5
3.Press “TAKE” button
Preset Mapping
Preset + A~H(1-8 storage site) + Take
Ex: Preset saved
mapping from 5
1.Press “PRESET” button
P
-
2.Press number key “E” to select the storage site 5
P
5
3.Press “TAKE” button
Learn default EDID
Default EDID + A~H(1-8 default EDID) + I~IV(input
1~4) + Take
Ex: Default EDID 2
Input 3
1.Press “DEFAULT EDID” button
E
d
2.Press number key “B” to select default EDID 2
2
d
3.Press number key “III” to select Input 3
2
3
4.Press “TAKE” button
0 or F
0 (success)
F (fail)
Learn Output EDID
Learn + A~B(Output 1~2) +Ⅰ~Ⅳ(input 1~4) + Take
Ex: Learn Output 4
Input 3
1.Press “LEARN” button
E
L
2.Press number key “D” to select Output 4
4
L
3. Press number key “III” to select Input 3
4
3
4.Press “TAKE” button
0 or F
0 (success)
F (fail)
Mute Output
Mute + A~B(Output 1~2) + Take
Ex: Mute Output 3
1. Press “MUTE” button
-
0
2. Press number key “C” to select Output 3
3
0
3.Press “TAKE” button
0
3

-9-
Method C: Software Control through RS-232 port
1. System Requirement
(1) OS Information: MS Win XP/7/8.1/10
(2) Baud rates: 115200
(3) Software size: 2 MB
(4) Minimum RAM requirement: 256 MB
1
Power ON/ Standby mode
5
I/O Routing Tab
2
Control SW via RS-232
6
EDID Tab
3
Control SW via Network
7
Rename I/O Tab
4
COM Port Selection
8
System Tab
1
2
5
6
7
8
4
3
-10-
1. I/O Mapping Tab
I/O Mapping
Switch the input for each output
Recall Mapping
Select the stored Mapping(1-8)
Click “Recall” button to recall previous mapping which are saved
Save Mapping
Select Mapping(1-8)
Click “Save” button to save current mapping

-11-
2. EDID Tab
Learn EDID from Default to Input
Select Default EDID(1-17 Default EDID)
Select designated Input
Click “Apply” button to learn from default EDID
Learn EDID from Display to Input
Select output
Select designated Input
Click “Apply” button to learn from HDBT output EDID
*Loopout does not support learning EDID function
Load EDID File to Input
Click “Load File” button to select the EDID file
Select designated Input
Click “Apply” button to load EDID file
View EDID
Select Input, HDBT output or EDID file
Click “View” button to read and analyze the EDID information
-12-
3. Rename I/O Tab
Rename I/O
Rename the Inputs
Rename the Outputs
Rename Mapping
Rename the Mappings

-13-
4. System Tab
Network –DHCP Mode
Click DHCP and then click the “Read” button to automatically get the IP address Info
Network –Static Mode
Click Static and then key in the “IP”, “MASK”, ”GATEWAY” information. After setting IP address,
please click “Save” to save IP address Info
“Read” button *The default IP address is 192.168.1.70
Read the IP address from the device
“Save” button
Save the key- in IP address
Cloud setting –Association Code
To get an “association code”. The device can use this code to pair with cloud server
Cloud –Reset Cloud
To reset cloud after a successful pairing
-14-
MAC
Read the device’s MAC address information
System –Factory Reset
To do factory default reset
System –Firmware Version
To get the F/W version information
Firmware Update
Before you start to update, please make sure you have secured the connection between your
computer COM port and the device.
*When using Ethernet port to do software control, it cannot use firmware update function
Main Board
Click the “Main Board” icon to open the Firmware Update Tool window
Click the button to select the file which you want to write into device
Click the button and the firmware will start to update
Front Panel
Click the “Front Panel” icon to do front panel firmware update, the firmware update
window of front panel shows up as below

-15-
Click the button to select the file which you want to write into device
Click the button and the firmware will start to update
After updating, please power cycle the device
Input
Before you start to do input firmware update, please ensure you have connected the
software through RS-232 port
Click the “Input” icon to open the FW Update for Compression IC window
Click the button to select the firmware file which you want to write into
device
Click the button and the firmware will start to update
After updating, please power cycle the device
Output
Before you start to do output firmware update, please ensure you have connected the
software through RS-232 port
Click the “Output” icon to open the FW Update for Compression IC window
-16-
Click the button to select the firmware file which you want to write into
device
Click the button and the firmware will start to update
After updating, please power cycle the device
LoopOut
Before you start to do output firmware update, please ensure you have connected the
software through RS-232 port
Click the “LoopOut” icon to open the firmware update window and the window of
loopout shows up as below
Click the button to load the firmware file
Click the button to do firmware update
After updating, please power cycle the device

-17-
Method D: Web Interface Control
The default IP address: 192.168.1.70
1
I/O Routing Tab
3
EDID Tab
2
Rename I/O, Mapping Tab
4
Power ON/Standby mode
1. I/O Routing Tab
I/O:
Switch the input for each output
Save Mapping
Select Mapping 1~8
Click “Save” button to save current mapping
Recall Mapping
Select the stored Mapping 1~8
Click “Recall” button to recall previous saved mapping
4
1
2
3
-18-
2. Rename I/O, Mapping Tab
Rename I/O:
Rename the Inputs
Rename the Outputs
Rename Mapping:
Rename the Mappings