Goodlife UltraSweep Traveler User manual

UltraSweepTM Traveler Instruction Manual
Engine-mounted rodent repeller to protect parked vehicles
Protects Repels
Included Parts
Getting Started
Safety Precautions
Sold Separately
POWER CORD
WITH FUSE
ULTRASWEEPTM TRAVELER 4 CABLE TIES OPTIONAL
LED FLASHING LIGHTS
• Cars, trucks, RVs, boats, small planes, ATVs, and other
parked vehicles.
• Read entire manual before use
• Before installation, ensure both the repeller and your vehicle engine are turned OFF
• Mount the repeller so that the speaker is facing into the engine area
• Never run wires along hot pipes or hoses
• Use strong high-temperature double sided tape or the included cable ties for mounting
• Do not let the wires sag; keep them secured with the included cable ties alongside existing wiring
• Do not mount the device below the engine where it might be exposed to water
• Keep away from children
• Do not use near small animal pets such as rabbits
• Do not place your ear next to the device
• Do not open the device, or use it near water
• Before powering the device “on”, check cable-to-battery polarity (red to positive, black to negative)
• Periodically conrm that the device and all wires are secure and not touching any hot pipes or hoses
• Mice, rats, chipmunks, squirrels, and other small rodents.
The UltraSweepTM Traveler will work automatically when your engine stops, and will go into standby mode when the engine is
running. It has two white ashing LEDs and one middle red/green LED that displays each power mode.
STANDBY MODE
When your engine is on, the repeller will automatically detect the vibration and go into a standby state. The red LED will ash
every 5 seconds to indicate standby mode.
WORKING MODE
Once the engine stops, the UltraSweepTM Traveler will go into working mode. After 120 seconds the red LED will turn green. The
repeller will run in Quiet Mode for 3 minutes. Then it will go into Super Mode for 80 seconds (if you have the optional LED strands
attached, they will ash every 5 seconds while the device is in Super Mode). The UltraSweepTM Traveler will continue to alternate
between Quiet and Super Modes to prevent pests from adapting to the frequencies and ashing lights.

UltraSweepTM Traveler Instruction Manual
Installation
1Ensure the repeller and your vehicle engine are OFF. This device uses a rocker switch:“–”for ON and“O” for OFF.
a. If the engine is not running, the device will wait 2 minutes and then go into Working Mode. (green LED will ash)
b. If the vehicle engine is running, the middle LED will ash red and go into Standby Mode.
c. There is a 2 minute delay between each mode.
2Run the black spade connector to the negative terminal of the battery and secure it.
4Connect the 2-wire white plug on the other end of the power cord into the unit with the connector tab facing up.
3Run the red spade connector to the positive battery terminal and secure that connection. The red power cable
has a 1amp 250V, 20mm x 5mm fuse in series for safety. Ensure these wires are connected for a safe installation.
5If you have the optional LED Cable, plug that into the larger port on the device. Each of the 2-wire LED strands
maybe gently separated to space the lights out across your vehicle’s engine bay.
6Turn the unit on. LEDs 1 and 3 will ash white, and the center LED with ash red. Next it will go into detection
mode to determine if the engine is running.
7Secure all wires with zip ties or high-temperature double sided tape. Ensure no wires are touching hot pipes or hoses.
We’re Here to Help
Toll Free: 1-800-657-8214
Outside US: 1-541-245-4488
Warranty
Specications
Don’t worry, we’ve got you covered! Your UltraSweepTM Traveler is backed by a 1-Year Manufacturer’s Warranty. For full details, please visit
www.pestrepellerultimate.com/pages/guarantee or contact us using the information below.
Website: pestrepellerultimate.com
Email: [email protected]
©2020 Good Life, Inc. DESIGNED IN OREGON MADE IN CHINA
POWER
Working Voltage 12 V DC
Working Current Standby mode: 2 mA
Quiet mode: 12 – 35 mA
Working mode: 50 – 100 mA
Ultrasonic Frequency 20 – 70 kHz
In-Line Fuse 1 Amp 250 V, 20mm x 5mm
LED FUNCTION
Standby Mode (Engine On) Unit turns o; LED ashes red
Working Mode (Engine OFF) Unit turns on; LED ashes green
Automatic Detection 2 minute delay between modes
FOR LONG-TERM USAGE
As with any electrical device, the UltraSweepTM Traveler requires current to work. If your vehicle is going to be parked for a long
period of time, the vehicle should be started every 1-2 weeks to let the battery charge. This will prevent the battery from being
drained too low. This will vary based on the condition of your battery, weather and environmental conditions, and if anything else
is hooked up to the same battery.