Goodman MBR Series Technical document

TECHNICALINFORMATION MANUAL
MBR/MBE
Blowers
•RefertoServiceManualRS6100004forinstallation,op-
eration,andtroubleshootinginformation.
•Allsafetyinformationmustbefollowedas provided inthe
ServiceManual.
•Refer to the appropriate Parts Catalog for part number
information.
Models listed
on page 3
RT6223002Rev.4
July2008
Copyright © 2004-2008 Goodman Manufacturing Company, L.P.
This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does not assume
any responsibility for property damage or personal injury due to improper service procedures or services
performed by an unqualified person.

PRODUCT IDENTIFICATION
2
Motor Type
R:ConstantSpeed
E:VariableSpeed
Electrical Supply
DesignSeries
Airflow Delivered
MB R 08 00 A A 1
Circuit Breaker
Factory Heat
DesignSeries
The model number is used for positive identification of component parts used in manufacturing. Please use this number
whenrequestingservice or partsinformation.
WARNING
WARNING
WARNING
WARNING
HIGHVOLTAGE!
DisconnectALLpowerbeforeservicingorinstallingthisunit.Multiple
power sources may be present. Failure to do so may cause property
damage, personal injury or death.
Installationandrepair ofthis unit shouldbe performedONLY byindividuals
meeting the requirements of an "entry level technician" as specified by the
Air-Conditioning, Heating and Refrigeration Institute (AHRI). Attempting to
install or repair this unit without such background may result in product
damage, personal injury or death.
WARNING
WARNING
Goodmanwillnotberesponsibileforanyinjuryorpropertydamagearising
from improper service or service procedures. If you install or perform
service on this unit, you assume responsibility for any personal injury or
property damage which may result. Many jurisdictions require a license to
install or service heating and air conditioning equipment.
08: 800 CFM
12: 1200CFM
16: 1600CFM
20: 2000CFM
MB: ModularBlower
A: No Circuit Breaker
B: Circuit Breaker
1: 208-230V/60Hertz/1Phase
A: First Series
00: NoHeat

PRODUCT IDENTIFICATION
3
The model number is used for positive identification of component parts used in manufacturing. Please use this number
whenrequestingservice or partsinformation.
MBR0800
MBR1200
MBR1600
MBR2000
WARNING
WARNING
WARNING
WARNING To prevent the risk of property damage, personal injury, or death, do not
store combustible materials or use gasoline or other flammable liquids or
vapors in the vicinity of this appliance.
Do not connect or use any device that is not design certified by Goodman
for use with this unit. Serious property damage, personal injury, reduced
unit performance and/or hazardous conditions may result from the use of
suchnon-approveddevices.
WARNING
WARNING The United States Environmental Protection Agency(“EPA”) has issued vari-
ous regulations regarding the introduction and disposal of refrigerants in-
troduced into this unit. Failure to follow these regulations may harm the
environment and can lead to the imposition of substantial fines. These
regulations may vary by jurisdiction. Should questions arise, contact your
local EPA office.
MBE1200
MBE1600
MBE2000

PRODUCT DESIGN
4
MBR/MBE blower cabinets are designed to be used as a
two-piece blower and coil combination. MBR/MBE blower
sectionscanbeattachedtocasedevaporatorcoil. Thistwo
piecearrangementallowsforavariety of mix-matching pos-
sibilitiesprovidinggreaterflexibility.
The MBE blower cabinet uses a variable speed motor that
maintains a constant airflow with a higher duct static. It is
approvedforapplicationswith coolingcoils ofupto0.8inches
W.C. external static pressure and includes a feature that
allowsairflow tobechangedby±15%. TheMBRblower cabi-
net uses a PSC motor. It is approved for applications with
cooling coils of up to 0.5 inches W.C. external static pres-
sure.
TheMBR/MBEblower cabinets areintendedtobeused with
acasedevaporator coil andacondensingunit or heatpump.
The blower section of the cabinet can also be used as an
electric furnace. The electric heating elements are field-in-
stalled. Electric heater kits (HKR) are available as sales
accessoriesforsupplementalelectric heat.
TheMBR/MBE blowercabinetswithproper coilmatchescan
bepositioned for upflow,counterflow,horizontalright or hori-
zontal left operation. All units are constructed with R-4.2
insulation. In areas of extreme humidity (greater than 80%
consistently), insulate the exterior of the blower with insula-
tionhavinga vapor barrier equivalent toductworkinsulation,
providinglocalcodes permit.
TheCAPX/CHPXcoilsareequippedwith a thermostatic ex-
pansionvalvethathas abuilt-ininternalcheckvalveforrefrig-
erantmetering. TheCACF/CAPF/CHPFcoilsareequipped
with a fixed restrictor orifice.
Thecoilsaredesignedforupflow,counterflow,orhorizontal
application,usingtwospeeddirectdrivemotorsontheCACF/
CAPX/CAPF/CHPF/CHPX models, and BPM (Brushless
Permanent Magnet) or ECM motor on the MBE models.

MBR/MBE BLOWER SPECIFICATIONS
5
W
H
(3) KNOCKOUTS
1.125
1.375
1.750
.875 KNOCKOUT
(2 PLACES)
C
6 1/2
5
5 1/8 3 1/4
D
MBR800/1200/1600/2000 & MBE1200/1600/2000
1Minimum Circuit Ampacity (MCA) and Maximum Overcurrent Protection (MOP) for blower without supplemental heat installed.
Refer to unit nameplate for MCA and MOP with approved accessory heaters installed.
Physical Information Shipping
MODEL Blower Wheel
(D x W) Blower Motor (HP) MCA1MOP1WHD
Weight
lbs.(kg)
MBR800 9X6 1/4 1.9 15
MBR1200 9x8 1/3 3.0 15
MBE1200 10X8 1/2 3.2 15
MBR1600 10X8 1/3 3.8 15
MBE1600 10X8 3/4 5.7 15
MBR2000 10X10 1/2 4.9 15
MBE2000 11X10 3/4 4.4 15 94
(42.6)
17½
(445) 26 (660) 21 (533) 72 (32.6)
21
(533) 30 (762) 21 (533) 82 (37.2)
Dimensions, inches (mm)
24½
(622) 30 (762) 21 (533)

MBR/MBE BLOWER SPECIFICATIONS
6
SMALL MEDIUM LARGE
8.840
10.159
16.500
11.029
11.209
20.021
13.178
11.209
23.464
BLOWER OPENING DIMENSIONS
(TOP VIEW)
MBR800/1200/1600/2000 & MBE1200/1600/2000

MBR/MBE BLOWER SPECIFICATIONS
7
HKR HEATER DATA
HKR-15C* HKR-20C* HKR-21C* ^HKR3-15* ^HKR3-20*
MBR
0800AA-1AA~~~~~
1200AA-1AA X X X X X
1600AA-1AA X X X X X
2000AA-1AA X X X X X
MBE
1200AA-1AAX~~~~
1600AA-1AAX~~~~
2000AA-1AAXX~~~
1200AA-1BAX~~~~
1600AA-1BAX~~~~
2000AA-1BAXX~~~
^ = Circuit 1: Single Phase for Air Handler Motor * = Revision level that my or may not be designated
Circuit 2: 3-Phase for HKR3 Heater Kits C= Circuit Breaker option
X = Allowable combinations
~ = Restricted combinations
BLOWER ELECTRIC HEATER KIT
NO HEAT KIT HKR-03* HKR05-(C)' HKR-06* HKR-08(C)* HKR-10(C)*
MBR
0800AA-1AA X X X X X X
1200AA-1AA X X X X X X
1600AA-1AA X X X X X X
2000AA-1AA X X X X X X
MBE
1200AA-1AA X~~~XX
1600AA-1AA X~~~~X
2000AA-1AA X~~~~X
1200AA-1BA XXXXXX
1600AA-1BA XXXXXX
2000AA-1BA XXXXXX
^ = Circuit 1: Single Phase for Air Handler Motor * = Revision level that my or may not be designated
Circuit 2: 3-Phase for HKR3 Heater Kits C = Circuit Breaker option
X = Allowable combinations
~ = Restricted combinations
BLOWER ELECTRIC HEATER KIT

8
BLOWER PERFORMANCE DATA
DIPSWITCH
NUMBER FUNCTION
1
2
3N/A
4 Indoor Thermostat
5
6
7
8
DIPSWITCH FUNCTIONS
Electric Heat
Cooling & Heat
Pump CFM
CFM Trim Adjust
MODEL SWITCH 1 SWITCH 2 CFM
OFF OFF 1200
ON OFF 1000
OFF ON 800
ON ON 600
OFF OFF 1600
ON OFF 1400
OFF ON 1200
ON ON 1000
OFF OFF 2000
ON OFF 1800
OFF ON 1600
ON ON 1200
MBE1200
MBE1600
MBE2000
MODEL SWITCH 5 SWITCH 6 CFM
OFF OFF 1200
ON OFF 1000
OFF ON 800
ON ON 600
OFF OFF 1600
ON OFF 1400
OFF ON 1200
ON ON 1000
OFF OFF 2000
ON OFF 1800
OFF ON 1600
ON ON 1200
MBE1200
MBE1600
MBE2000
MBE BLOWER PERFORMANCE SPECIFICATIONS
MBR BLOWER PERFORMANCE SPECIFICATIONS
CFM SWITCH 7 SWITCH 8
+10% ON OFF
-15% OFF ON
Thermostat "Fan Only" Mode
During"FanOnly"operations,the CFM output is 30% of the
cooling setting.
CFMTrimAdjust
Minoradjustmentscanbemade through the dipswitch com-
binationof7-8.
SPEED STATIC MBR0800**-*
SCFM MBR1200**-* SCFM MBR1600**-* SCFM MBR2000**-* SCFM
0.1 1240 1500 1800 2160
0.2 1170 1460 1740 2080
0.3 1120 1360 1680 1990
0.4 1060 1280 1610 1890
0.5 980 1200 1520 1790
0.6 900 1110 1430 1690
0.1 900 1380 1540 1730
0.2 850 1320 1490 1670
0.3 790 1270 1450 1590
0.4 740 1200 1400 1520
0.5 680 1140 1350 1420
0.6 605 1040 1280 1320
0.1 650 1170 1130 1520
0.2 590 1130 1100 1450
0.3 540 1080 1070 1360
0.4 500 1020 1030 1290
0.5 430 950 990 1200
0.6 330 830 930 1090
External static is for blower @ 230 volts, it does not include coil, air filter or electric heaters.
HIGH
MEDIUM
LOW

WIRING DIAGRAMS
9
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
Low Voltage Wiring Diagram for Cooling Unit with optional heat kit 10KW and below
Low Voltage Wiring Diagram for Cooling Unit with optional heat kit 15KW and above
RED
GREEN
WHITE
BLUE
TO CONDENSING
UNIT 24V. CONNECTIONS
#18 GA. 2 WIRES
ROOM THERMOSTAT
WY G R
R
G
W
Y
#18 GA. 4 WIRES WITH
COOLING 3 WIRES WITHOUT
MBR UNIT
ROOM THERMOSTAT
W2 W Y G R
TO CONDENSING
UNIT 24V. CONNECTIONS
#18 GA. 2 WIRES
CONTACTOR
COIL
#18 GA. 2 WIRES
OUTDOOR
THERMOSTAT
(OPTIONAL)
R
G
W
Y
#18 GA. 4 WIRE WITH
COOLING 3 WIRE WITHOUT
GREEN
RED
WHITE
BROWN
BLUE
MBR UNIT

WIRING DIAGRAMS
10
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
CW2 Y R
HEAT PUMP
B
L
U
E
W
H
I
T
E
O
R
A
N
G
E
Y
E
L
L
O
W
R
E
D
Y O C R E
ROOM THERMOSTAT
MBR UNIT
GREEN
BLUE
#18 GA. 5 WIRES
OUTDOOR THERMOSTATS
(OPTIONAL) MAKE ON FALL
BL
#18 GA. 6 WIRE NEEDED WHEN OT IS USED
OT - 1
SYSTEM COMPOSITE DIAGRAM
MBR0800
10kW & BELOW
Y
O
W2
R
BR
G
W
BL
RED
WHITE
W
G
SEE NOTE 3
O
R
HEAT PUMP ROOM THERMOSTAT
CW2 O Y R Y O G
W2 R E
R
C
BR
G
W
BL
BL
W
O
B
L
U
E
W
H
I
T
E
O
R
A
N
G
E
Y
E
L
L
O
W
R
E
D
RED
GREEN
WHITE
BROWN
BLUE
EHR
1 1
3 4
#18 GA. 5 WIRES
OT-1
OT-2
#18 GA. 7 WIRES
#18 GA. 7 WIRE NEEDED WHEN (2) OTs ARE USED.
NOTES
1) OUTDOOR THERMOSTAT (OT-1) SHOULD BE THE
FIRST TO CLOSE AND THE FIRST TO OPEN.
2) IF OUTDOOR THERMOSTAT IS NOT USED, TIE WHITE
AND BROWN WIRES FROM AIR HANDLER TOGETHER.
3) REMOVE WIRE WHEN USING OUTDOOR T-STAT.
#18 GA. 7 WIRE NEEDED WHEN (2) OTs ARE USED.
NOMENCLATURE
OT - OUTDOOR TEMPERATURE (OPTIONAL)
MOF - MAKE ON FALL
EHR - EMERGENCY HEAT RELAY (OPTIONAL)
COLOR CODES
R - RED
Y - YELLOW
BL - BLUE
V - VIOLET
BR - BROWN
O - ORANGE
W - WHITE
G - GREEN
SYSTEM COMPOSITE DIAGRAM
MBR1200-2000
ABOVE 10kW
SEE
NOTE 3
YSEE
NOTE 2
MBR UNIT

WIRING DIAGRAMS
11
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
COOLING ONLY - 2 STAGE HEAT THERMOSTAT
NOTES:
1.) Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES LO SPD FAN HEATING
W/W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
OTCORCE\W1 W/W2 Y1OT1 OT2
YCON
CONDENSER
PLEASEREFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
R
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
SWITCH
HEATER
W1 W2 24 VAC
C R
CONDENSING
UNIT
THERMOSTATS
IF NEEDED
Y/Y2GHUM
Y1
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
ROOM
THERMOSTAT
W2 CRGY W1
2nd STAGE HEATER
1st STAGE HEATER
SEE NOTE 4
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
COOLING ONLY - 2 STAGE HEAT (1st ROOM T'STAT & 2nd OT)
ROOM
THERMOSTAT
WCRGY
OT2OT1 Y1W/W2E\W1 C ROOTC
CONFIGURATION.
DIP SWITCH
FOR PROPER
TOMANUAL
PLEASE REFER
CONDENSER
YCONR
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
SWITCH
HEATER
W1 W2 24 VAC C R
CONDENSING
UNIT
THERMOSTATS
IF NEEDED
HUMGY/Y2
Y1
SEE NOTE 4
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
NOTES:
1.) Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES LO SPD FAN HEATING
E/W1 WITH OT CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
2nd STAGE HEATER
1st STAGE HEATER
OUTDOOR
THERMOSTAT
1st STAGE ENABLED THRU ROOM T'STAT
2nd STAGE ENABLED THRU CLOSED OT
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
Single Stage Cooling with Single or Two-Stage Heating

WIRING DIAGRAMS
12
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
COOLING ONLY - 2 STAGE HEAT (T'STAT ENABLED OT)
NOTES:
1.) Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES LO SPD FAN HEATING
W/W2 WITH OT CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
OT2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION OT2
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
(CFM)
HUM
ON
DIP
OFF
YCON
CONDENSER
R
E\W1
CONDENSING
UNIT
OUTDOOR
THERMOSTATS
HEATPUMP
W1
OT1
COM O
W2
W2 ED
W/W2 O OTC OT1
W1 W2
SWITCH
HEATER CR
24 VAC
OT2 C RY1
W1
IF NEEDED
THERMOSTAT
ROOM
W2 CRG
2nd STAGE HEATER
1st STAGE HEATER
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
Y1
HUM
HUMIDISTAT
Y/Y2G
Y
OUTDOOR
THERMOSTAT
1st STAGE ENABLED THRU ROOM T'STAT
2nd STAGE ENABLED THRU ROOM T'STAT AND CLOSED OT2
HEATPUMP - WITH 1 STG EMHT 1 STG AUX HEAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E AND W2 ENABLE HI SPD FAN HEATING
3.) IF OT2 PJ2 JUMPER IS CUT E AND W2 ENABLE
LO SPD FAN HEATING
HUMIDISTAT
(OPTIONAL)
IF NEEDED
OT2OT1 Y1W/W2E\W1 C ROOTC
CONFIGURATION.
DIP SWITCH
FORPROPER
TOMANUAL
PLEASE REFER
CONDENSER
YCONR
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
SWITCH
HEATER
W1 W2 24 VAC C R
THERMOSTATS HUMGY/Y2
Y1
HUMIDISTAT
SEE NOTE 4
1st STAGE HEATER
ROOM
THERMOSTAT
EC
RGY
HEATPUMP
RYCOW2
HEATPUMP
YCON
CONDENSER
RCOM OW2 ED
W2 O
REMOVE
PRODUCTION
WIRE Y1 - O
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION

WIRING DIAGRAMS
13
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
1st STAGE HEATER
REMOVE
PRODUCTION
WIRE Y1 - O
Y
ROOM
IF NEEDED
THERMOSTATS
THERMOSTAT
W2
EOC
RG
SEE NOTE 4
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
2nd STAGE HEATER
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
CONDENSER
YCONR
R
HEATPUMP
COM OEDW2
C
HEATPUMP
YOW2
Y/Y2GHUMOTCORCE\W1 W/W2 Y1OT1 OT2
Y1
DIP
TOMANUAL
FORPROPER
DIP SWITCH
CONFIGURATION.
(CFM)
ON
OFF
HEATPUMP
W1
PLEASE REFER
HUM
OT2
OT1
YCON
CONDENSER
RCOM O
W2
HEATER
SWITCH
W2
W1 24 VAC C R
W2 ED
OUTDOOR
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) 0T2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
YCON
CONDENSER
R
R
HEATPUMP
COM OEDW2
HEATPUMP
C
YOW2
OT2
PLEASE REFER
CONFIGURATION.
DIP SWITCH
FOR PROPER
TOMANUAL
(CFM)
HUM
DIP
OFF
ON
2nd STAGE HEATER
1st STAGE HEATER
Y
Y1
W1
HEATPUMP
OTC
CONDENSER
YCONR
OT1
COM O
E\W1 W/W2 O
SWITCH
HEATER
W2W1
W2
W2 ED
RC
24 VAC
THERMOSTATS
OUTDOOR
OT1 OT2 CRY1
IF NEEDED
THERMOSTAT
ROOM
W2
EOR CG
SEE NOTE 4
REMOVE
PRODUCTION
WIRE Y1 - O
HUMIDISTAT
Y/Y2GHUM
HUMIDISTAT
(OPTIONAL)
1st STAGE AUX HEAT ENABLED BY ROOM T'STAT
2ND STAGE AUX ENABLED BY ROOM T'STAT AND OUTDOOR T'STAT
HEATPUMP - 2 STG EMHT 2 STG AUX - 1 OUTDOOR T'STAT
OUTDOOR
THERMOSTAT
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION

WIRING DIAGRAMS
14
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
ROOM
THERMOSTAT
OT2
THERMOSTATS
W1
HEATER
OT1OW/W2E\W1 OTC
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 AND OT1 CLOSED ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 AND 0T2 PJ2 MUST BE CUT
FOR THIS CONFIGURATION
PLEASE REFER
TOMANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
(CFM)
R
OT1
HUM
OT2
W2W1
HEATPUMP
COM
CONDENSER
YCON OEDW2
OUTDOOR
O
HEATPUMP
HEATPUMP
RCONDENSER YCON OCOM
RYC
OT2
W2 ED
W2 OE W2
HUMGY/Y2Y1RC
REMOVE
PRODUCTION
WIRE Y1 - O
DIP
1st STAGE HEATER
2nd STAGE HEATER
ON
OFF
SWITCH
W2 24 VAC CR
Y1
HUMIDISTAT
IF NEEDED
G
CRY
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
OT1
OT2
OUTDOOR
OT1OTC
NO AUX HEAT IN HEATPUMP MODE UNTIL OUTDOOR T'STAT CLOSES
HEATPUMP - 2 STG EMHT 2 STG AUX - 2 OUTDOOR T'STATS
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) 0T2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
YCON
CONDENSER
R
R
HEATPUMP
COM OEDW2
HEATPUMP
C
YOW2
OT2
PLEASE REFER
CONFIGURATION.
DIP SWITCH
FOR PROPER
TOMANUAL
(CFM)
HUM
DIP
OFF
ON
2nd STAGE HEATER
1st STAGE HEATER
Y
Y1
W1
HEATPUMP
OTC
CONDENSER
YCONR
OT1
COM O
E\W1 W/W2 O
SWITCH
HEATER
W2W1
W2
W2 ED
RC
24 VAC
THERMOSTATS
OUTDOOR
OT1 OT2 CRY1
IF NEEDED
THERMOSTAT
ROOM
W2
EOR CG
SEE NOTE 4
REMOVE
PRODUCTION
WIRE Y1 - O
HUMIDISTAT
Y/Y2GHUM
HUMIDISTAT
(OPTIONAL)
1st STAGE AUX HEAT ENABLED BY ROOM T'STAT
2ND STAGE AUX ENABLED BY ROOM T'STAT AND OUTDOOR T'STAT
HEATPUMP - 2 STG EMHT 2 STG AUX - 1 OUTDOOR T'STAT
OUTDOOR
THERMOSTAT
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION

WIRING DIAGRAMS
15
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
Two-Stage Cooling with Conventional Two-Stage Thermostat
ROOM
THERMOSTAT
WCRGY2
Y1
RSG - 2 SPD
2 SPD COOLING ONLY - WITH 1 STAGE ELECTRIC HEAT
NOTES:
1.) Y1ENABLES LO SPD FAN COOLING
Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES HI SPD FAN HEATING
3.) IF OT1 PJ4 JUMPER IS CUT E/W1 ENABLES
LO SPD FAN HEATING
HUMIDISTAT
(OPTIONAL)
CONDENSING
UNIT
IF
N
E
E
D
E
D
OT2 OT1 Y1 W/W2 E\W1 CR OOTC
CONFIGURATION.
DIP SWITCH
FOR PROPER
TO MANUAL
PLEASE REFER
CONDENSER
YCON R
DI
P
(CFM) O
NO
FF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
S
WI
T
C
H
HEATER
W1 W2 24 VAC CR
THERMOSTATS HUM
GY/Y2
Y1
HUMIDISTAT SEE NOTE 4
1st STAGE HEATER
Y2
CX
Y1
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
ROOM
THERMOSTAT
WCRGY2
Y1
RSG - 2 SPD
2 SPD COOLING ONLY - WITH 2 STAGE HEAT THERMOSTAT
NOTES:
1.) Y1ENABLES LO SPD FAN COOLING
Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES HI SPD FAN HEATING
3.) IF OT1 PJ4 JUMPER IS CUT E/W1 ENABLES
LO SPD FAN HEATING
HUMIDISTAT
(OPTIONAL)
CONDENSING
UNIT
IF
N
E
E
D
E
D
OT2 OT1 Y1 W/W2 E\W1 CR OOTC
CONFIGURATION.
DIP SWITCH
FOR PROPER
TO MANUAL
PLEASE REFER
CONDENSER
YCON R
DI
P
(CFM) O
NO
FF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
S
WI
T
C
H
HEATER
W1 W2 24 VAC CR
THERMOSTATS HUM
GY/Y2
Y1
HUMIDISTAT SEE NOTE 4
1st STAGE HEATER
Y2
CX
Y1
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
W2

WIRING DIAGRAMS
16
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
NOTES:
1.) Y1 ENABLES LO SPD FAN COOLING
Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES LO SPD FAN HEATING
W/W2 WITH OT CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
OT2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
OT2
PLEASE REFER
TOMANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
(CFM)
HUM
ON
DIP
OFF
YCON
CONDENSER
R
E\W1
CONDENSING
UNIT
OUTDOOR
THERMOSTATS
HEATPUMP
W1
OT1
COM O
W2
W2 ED
W/W2 O OTC OT1
W1 W2
SWITCH
HEATER CR
24 VAC
OT2 C RY1
IF NEEDED
2nd STAGE HEATER
1st STAGE HEATER
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
Y1
HUM
HUMIDISTAT
Y/Y2G
OUTDOOR
THERMOSTAT G
THERMOSTAT
W1 W2
ROOM
R
CY1 Y2
RSG - 2 SPD
2 SPD COOLING ONLY - 2 STAGE HEAT (T'STAT ENABLED OT)
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
Y2
CX
Y1
Two-Stage Cooling with Conventional Two-Stage Thermostat
OT2OT1 Y1W/W2E\W1 C ROOTC
CONFIGURATION.
DIP SWITCH
FOR PROPER
TOMANUAL
PLEASE REFER
CONDENSER
YCONR
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
SWITCH
HEATER
W1 W2 24 VAC C R
THERMOSTATS
IF NEEDED
HUMGY/Y2
Y1
SEE NOTE 4
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
NOTES:
1.) Y1 ENABLES LO SPD FAN COOLING
Y/Y2 ENABLES HI SPD FAN COOLING
2.) E/W1 ENABLES LO SPD FAN HEATING
E/W1 WITH OT CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
2nd STAGE HEATER
1st STAGE HEATER
OUTDOOR
THERMOSTAT G
ROOM
THERMOSTAT
WCRY1 Y2
RSG - 2 SPD
CONDENSING
UNIT
2 SPD COOLING ONLY - 2 STAGE HEAT (1st T'STAT 2nd OT)
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
Y2
CX
Y1

WIRING DIAGRAMS
17
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
Heat Pump with Single or Two-Stage Heating (Options for Emergency Heat)
with Conventional Thermostat
HEATPUMP - WITH 1 STG EMHT 1 STG AUX HEAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E AND W2 ENABLE HI SPD FAN HEATING
3.) IF OT2 PJ2 JUMPER IS CUT E AND W2 ENABLE
LO SPD FAN HEATING
HUMIDISTAT
(OPTIONAL)
IF NEEDED
OT2OT1 Y1W/W2E\W1 C ROOTC
CONFIGURATION.
DIP SWITCH
FORPROPER
TOMANUAL
PLEASE REFER
CONDENSER
YCONR
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1 W2
HEATPUMP
COM OW2 ED
SWITCH
HEATER
W1 W2 24 VAC C R
THERMOSTATS HUMGY/Y2
Y1
HUMIDISTAT
SEE NOTE 4
1st STAGE HEATER
ROOM
THERMOSTAT
ECRG
Y
HEATPUMP
RYCOW2
HEATPUMP
YCON
CONDENSER
RCOM OW2 ED
W2 O
REMOVE
PRODUCTION
WIRE Y1 - O
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
RYCON
COM OW2 ED
HEATPUMP
CONDENSER
COW2
HEATPUMP ROOM
THERMOSTAT
W2
EC YR RYG
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
2nd STAGE HEATER
1st STAGE HEATER
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE
IN THE "ON" POSITION
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1
OTCW/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
O

WIRING DIAGRAMS
18
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
RYCON COM OW2 ED
HEATPUMP
CONDENSER
COW2
HEATPUMP ROOM
THERMOSTAT
W2
EC
YR RYG
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
2nd STAGE HEATER
OUTDOOR
THERMOSTAT
NOTES:
1.) Y ENABLES HISPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD
FAN HEATING
3.) OT2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE
IN THE "ON" POSITION
HEATPUMP - 2 STG EMHT 2 STAG AUX - 1 OUTDOOR T-STAT
1ST STAGE HEATER
O
1ST STAGE AUX HEAT ENABLED BY ROOM T'STAT
2ND STAGE AUX ENABLED BY ROOM T'STAT AND OUTDOOR T'STAT
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.
RYCON
COM OW2 ED
HEATPUMP
CONDENSER
COW2
HEATPUMP ROOM
THERMOSTAT
W2
EC
YR RYG
IF
N
E
E
D
E
D
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
2nd STAGE HEATER
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 AND OT1 CLOSED ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 AND OT2 PJ2 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
HEATPUMP - 2 STG EMHT 2 STAG AUX - 2 OUTDOOR T-STATS
1ST STAGE HEATER
OT1 OT2OTC
OUTDOOR
O
NO AUX HEAT IN HEATPUMP MODE UNTIL OUTDOOR T'STAT CLOSES
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.

WIRING DIAGRAMS
19
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
RYCON COM OW2 ED
HEATPUMP
CONDENSER
COW2
HEATPUMP ROOM
THERMOSTAT
W2
EC YR RYG
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
2nd STAGE HEATER
OUTDOOR
THERMOSTAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 AND OT2 PJ2 MUST BE CUT
FOR THIS CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "ON" POSITION
HEATPUMP - 2 STG EMHT 1 STG AUX - 1 OUTDOOR T'STAT
1ST STAGE HEATER
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1
OTCW/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.
NO AUX HEAT IN HEATPUMP MODE UNTIL OUTDOOR T'STAT CLOSES
O

WIRING DIAGRAMS
20
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
Two Speed Heat Pump with Single or Two-Stage Heating
(Options for Emergency Heat) with Conventional Two-Stage Thermostat
RYCON COM OW2 ED
HEATPUMP
CONDENSER
COW2
RTG
HEATPUMP ROOM
THERMOSTAT
W2
EC
Y2RRY2G
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
NOTES:
1.) Y ENABLES HISPD FAN COOLING
2.) E AND W2 ENABLE HI SPD FAN HEATING
3.) IF OT2 PJ2 JUMPER IS CUT, E AND W2 ENABLE LO
SPD FAN HEATING
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
HEATPUMP - WITH 1 STG EMHT 1 STG AUX HEAT
1ST STAGE HEATER
Y1 Y1
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.
O
RYCON COM OW2 ED
HEATPUMP
CONDENSER
COW2
RTG
HEATPUMP ROOM
THERMOSTAT
W2
ECY2RRY2G
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
NOTES:
1.) Y ENABLES HISPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "OFF" POSITION
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
1ST STAGE HEATER
Y1 Y1
2ND STAGE HEATER
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM OW2 ED
S
WI
TC
H
DI
PO
NO
FF
24 VAC
CR
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1
OTCW/W2E\W1 THERMOSTATS
GOODMAN MFG. CO. L.P.
O