GoPro RMRU3 User manual

THE REMOTE
WATERPROOF REMOTE CONTROL
USER GUIDE

The Basics
Wearing The Remote
The First Step
Charging
Powering On + O
1. Power Button
2. Status Light
3. Preset Button
4. Status Screen
5. Mode Button
6. Shutter Button
7. USB-C Port
2
1
3
4
5
6
7
CAUTION: Be sure the USB-C port is dry before inserting the cable.
You may need to upgrade your camera’s software before you can use
The Remote. For step-by-step instructions, go to gopro.com/update.
Flip open the USB-C port cover.
Insert the included USB-C cable into
the port. Connect the other end of
the cable to a computer or other USB
power source.
Note: Be sure that the computer is connected
to a power source. If the remote status screen
does not indicate that the remote is charging,
use a dierent USB port.
ATTACHING YOUR REMOTE TO THE STRAP
The attachment strap lets you wear your remote on your wrist or attach it to a
grip, bike handlebars, backpack straps, and more.
Heads Up: The Remote is waterproof to 16ft (5m), but will not work under water.
1. Thread the strap through the slots on the back of the remote.
2. Position the remote along the strap as shown.
3. Thread the end of the strap through the underside of the plastic ring.
4. Fold the strap back onto itself and use the hook and loop fastners to secure
the strap. Fold any excess strap back onto itself for added security.
POWERING ON
Press the Power button .
POWERING OFF
Press and hold the Power button
for two seconds.

The Remote can control up to 5 cameras at a time from up to 196 feet (60m)
away in optimal conditions. Your camera recognizes only one remote at a time.
*Dependent on camera model, terrain, obstructions, electromagnetic interference,
and environmental conditions.
PAIRING THE REMOTE WITH YOUR CAMERA
1. Power o The Remote.
2. On your camera, complete these steps:
a. From the rear screen, swipe down to access the Dashboard.
b. Swipe right, and then tap Connections > Connect Device > The Remote.
Your camera will automatically begin pairing.
3. Power on The Remote.
4. Look for “Pair New” on the remote’s screen. Press the Shutter button to
start pairing.
CONNECTING AFTER PAIRING
Your remote and camera will automatically connect when both are on.
Make sure your camera’s wireless connections are on if they fail to connect.
Tap Preferences > Connections > Wireless Connections to turn on wireless.
Heads Up: Your camera cannot be connected to The Remote and the GoPro
app at a time. You must disconnect the app to connect The Remote or power
o The Remote to connect the app.
Pairing the Remote and Your GoPro
CHANGING MODES
1. Press the Mode button repeatedly to cycle to the mode
that you want.
2. Press the Shutter button to start capturing.
3. To stop capturing video or time lapse, press the Shutter button again.
If your camera goes out of range of the remote while you are recording,
recording will continue until you stop it.
CHANGING PRESETS
Press the Preset button to see all the presets for the selected mode.
1. Press the Mode button repeatedly to cycle through the presets.
2. Press the Shutter button to select the preset that you want.
PRO TIP: Mark favorite moments by pressing the Mode button on the
remote during recording or playback. This adds a HiLight Tag that makes those
moments easier to find later.
THE FOLLOWING FEATURES ARE NOT AVAILABLE WHEN USING THE
REMOTE WITH YOUR GOPRO
• QuikCapture
• Continuous photo with multiple cameras
• Manual capture of photos while recording video with multiple cameras
Capturing Video and Photos
To see additional information regarding country certifications, refer to the
Important Product + Safety Instructions included with your remote.
Regulatory Information

XXXXXXXXXXX REVA
Visit gopro.com for more information
© 2020 GoPro, Inc. All rights reserved. Model/Modelo/型號: RMRU3

Features: radio
2.4 GHz BLE 5.0
Transmit power MAX 7dBm
Operation Frequency: 2402-2480MHz
MAX PK Antenna Gain: 0.64 dBi
Software version: V0.5
Hardware version: EVT1
The operation temperature is -10~35℃
Input Rated Voltage: 3.85Vdc

3025 Clearview Way, San Mateo, CA 94402 | GoPro GmbH, Floessergasse 2, 81369 München, Deutschland | (650) 332‐7600 | gopro.com
Manufacturer: GoPro, Inc.
DECLARATION OF CONFORMITY
3025 Clearview Way
San Mateo, CA 94402 USA
Declares under our sole responsibility that the product:
Product Type The Remote
Regulatory Model Number: RMRU3
Trade name: GoPro
Software version: v0.5
Hardware version: EVT1
Notified Body/NB No./Cert. No. TÜV SÜD Product Service GmbH/0123/TPS‐RED500273 i01
Country of Origin Made in China:
Conforms to the following Product Specifications:
Health & Safety
Article 3.1(a)
IEC 60950‐1:2005+ AMD1:2009 + AMD2:2013,
EN 60950‐1:2006+A11:2009+A1:2010+A12:2011+A2:2013
IEC 62368‐1:2014 (Second Edition), EN 62368‐1:2014+A11:2017,
IEC/EN 62479:2010
EMC
Article 3.1(b)
ETSI EN 301 489‐1 V2.2.3 (2019‐11),
ETSI EN 301 489‐17 V3.1.1 (2017‐02), Final Draft ETSI EN 301 489‐17 V3.2.3 (2020‐07)
EN 55032:2015,
EN 55035:2017,
EN IEC 61000‐3‐2: 2019
EN 61000‐3‐3: 2013/A1:2019
Radio
Article3.2
ETSI EN 300 328 V2.2.2 (2019‐07)
The product specified above complies with the essential requirements and other relevant requirements of the RED
2014/53/EU and the following Directives:
RoHS Directive 2011/65/EU
Sep 10, 2020
Date of Issue Frank Han (Senior Principal Engineer, Regulatory Compliance)

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The provided shielded USB cable must be used with this unit to ensure compliance with the
class B FCC limits.
RF Exposure Statement
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter used in other systems. This device complies with FCC radiation
exposure limits set forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy
that is deemed to comply without testing of specific absorption rate (SAR).
IC Regulations: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.
This device may not cause interference. 2. This device must accept any interference, including interference that may
cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
The Country Code Selection feature is disabled for products marketed in the US/Canada.
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
This device complies with RSS-102 radiation exposure limits set forth for an
uncontrolled environment.

IC Radiation Exposure Statement
This EUT is in compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and has been
tested in accordance with the measurement methods and procedures specified in IEEE 1528.
Réglementations de l’IC : cet appareil contient un ou plusieurs émetteurs/récepteurs exempts de
licence conformes aux normes CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. Son exploitation est soumise aux deux conditions
suivantes : 1. Cet appareil ne doit pas produire d’interférences. 2. Cet appareil doit accepter toutes les
interférences qu’il reçoit, y compris celles susceptibles de perturber son fonctionnement.
Cet appareil numérique de la classe B est conforme à la norme ICES-003 du Canada.
La fonction Sélection du code pays est désactivée pour les produits disponibles sur les marchés
américain/canadien.
Nach den Bestimmungen von Industry Canada darf diese Sendeanlage nur mit einer
Antenne des Typs und der maximalen (oder geringeren) Verstärkung verwendet werden,
die von Industry Canada für die Anlage bestätigt wurde. Um mögliche Störungen des
Funkverkehrs anderer Nutzer zu verringern, muss die Art und Verstärkung der Antenne so
gewählt werden, dass die Äquivalente Isotrope Strahlungsleistung (EIRP) nicht größer ist
als für eine erfolgreiche Kommunikation notwendig.
Dieses Gerät entspricht den Strahlungsbelastungsgrenzen der RSS-102, die für eine
nicht kontrollierte Umgebung festgelegt wurden.