Gorke Electronic
SPECIFICATION AND USER’s MANUAL: type of the device 2-channel OPC-K02 receiver page: 3
USER’S MANUAL
Important! Launching the programming mode is possible only when the relay is closed. In order to close the
relay, press the remote control’s button or disconnect the power supply temporarily. We recommend setting the
switch on the SERVICE position.
1. REGISTERING A 2-BUTTON REMOTE CONTROL
a) press the LEARNING button for more than 0,5 but less than 4 seconds – the K2 diode will light
b) press the button which is supposed to control the channel 1 – the diode K2 will fade
c) press the button which is supposed to control the channel 2 once more – the diode K2 will light for 3 seconds,
then it will start to pulse and will fade. The process of registering a new remote control is finished
If the process of registering a new remote control fails, the diode K2 will blink once and then fade. In this case,
you need to start the process from the beginning. If the receiver's memory is full (113 remote controls have
already been programmed), programming next remote control will delete the one which had been programmed
as the first. If the number of users is larger than 113, you need to consider using the configuration of the WLC
201 receiving module with an adequate number of RSU-K01/LC receivers (two for 226 users, 3 for 339 users,
etc.).
2. REGISTERING A 1-BUTTON REMOTE CONTROL ON THE CHANNEL 1
a) press the LEARNING button for more than 0,5 but less than 4 seconds – the K2 diode will light
b) press the remote control’s button – the diode K2 will fade
c) press this button once more – the diode K2 will light for 3 seconds, then it will start to pulse and then it will
fade
3. REGISTERING A ONE-BUTTON REMOTE CONTROL ON THE CHANNEL 2
a) press the LEARNING button for more than 0,5 but less than 4 seconds – the K2 diode will light
b) press the remote control button – the diode K2 will fade
c) press the same button once more – the K2 diode will light for 3 seconds and during this time press the
LEARNING button
d) the diode will pulse and then it will fade
e) the process of registering a new remote control is finished
If you want to use only one button of a multi-buttoned remote control (2, 4 or 8) to control channel 1 or 2,
proceed according to point 2 or 3.
4. SETTING THE RECEIVER'S OPERATING MODE
To set the receiver's operating mode, one needs to have a remote control which has previously been entered
into the receiver's memory (point 1.). Manufacturing settings – the bistable mode.
The monostable mode (timer) – after sending the transmission from the remote control, the receiver's relay
will open for the pre-programmed time
Press the LEARNING button (the diode K2 will light) and keep it pressed until the K2 diode starts to pulse – then
you need to release the button. After releasing the button, the K2 diode will emit continuous light for about 4
seconds and then, slowly pulse. Each blink corresponds to one second.
For example, in order to set timer on 20 seconds, you need to count 20 blinks of the K2 diode and press the
remote control’s button, thus confirming the length of time. The maximal time available to set is 260s (4
min20s). If no button is pressed during the diode pulsing (time countdown), after counting to 260s, the K2 diode
will emit continuous light for 1 minute. If during this time (the continuous lighting) the control button is pressed
(confirming), the receiver will set time on the maximum, that is, about 260s. If during this time the button is
NOT pressed, the receiver will quit the programming mode and will save the previous setting.
The bistable mode (flip-flop) – after receiving the transmission from the remote control, the relay flips on the
other state.
Press the LEARNING button (the K2 diode will light) and keep it pressed until the K2 diode starts to pulse – then
release the LEARNING button. After releasing the LEARNING button the K2 diode will emit continuous light for
about 2s and during this period one must press the control’s button.
5. DELETING THE REMOTE CONTROLS FROM THE MEMORY
Keep the LEARNING button pressed.
Phase one: the LED K2 will light for about 4s.
Phase two: LED K2 will start to pulse and then it will fade, which means that the deletion is finished. Release the
LEARNING button.
1. one must remember that deleting concerns the whole capacity of the memory. If you want to remove
only one or several remote controls, you must re-enter the ones which are supposed to be saved.
2. If there are many users and you want to avoid the toilsome process of programming the remote
controls individually, you can use one of the identifying receivers (their parameters allow for deleting
the controls individually)
3. deleting the senders does not change the operating mode of the receiver
4. disconnecting the supply voltage does not cause losing the information about programmed remote
controls or the operating mode of the receiver.
