Gosafe G626 User manual

G626 Tracking Device
User Manual | Version 2.00

TABLE OF CONTENTS
1. Device Introduction
1.1 Physical Appearance..................................................................................................3
1.2 Specification.................................................................................................................4
1.3 Features..........................................................................................................................4
2. Quick Install Instructions
2.1 Configuration...............................................................................................................5
2.2 Insert SIM card............................................................................................................5
2.3 Power on........................................................................................................................6
2.4 Installation Diagram...................................................................................................6
2.5 Set User No. .................................................................................................................6
2.6 Modify Password.........................................................................................................6
2.7 Set Work Mode............................................................................................................7
3.Commands for Device Setting
3.1 Set User No. .................................................................................................................7
3.2 Modify User Password..............................................................................................8
3.3 Set User Upload Mode, interval and type..........................................................8
3.4 Set Message Center Number..................................................................................9
3.5 Set APN...........................................................................................................................9
3.6 Power saving mode setting..................................................................................10
3.7 Setting uploading TCP server mode..................................................................12
3.8 Enable/Disable Over speed alarm......................................................................12
3.9 Movement sensor setting......................................................................................13
3.10 Enable/Disable Over Speed Alarm Parameter..............................................14
3.11 Enable/Disable SMS when movement trigger.............................................14
3.12 Location Poll............................................................................................................15
3.13 Set Time Zone..........................................................................................................16
3.14 Clear Alarm................................................................................................................16
3.15 Query SIM card balance.......................................................................................16
3.16 Commands Wait......................................................................................................17
3.17 Alarms.........................................................................................................................17
3.18 Default Parameters.................................................................................................19
3.19 Combine Command...............................................................................................19
4. Structures of SMS from Device
4.1 Normal Location SMS Format (G Mode)...........................................................20
4.2 Hyperlink SMS Format (W Mode)........................................................................20
4.3 Error Command Alert................................................................................................21
4.4 Password Modification Successful Confirmation...........................................21
4.5 User No. Setting Successful Confirmation........................................................21
4.6 Command Table.........................................................................................................21
5. LED Flashes & Relevant Device Status
6. Appendix
6.1 Characters for Commands.....................................................................................26
3
5
7
25
20
26

1.Device Introduction
G626 is a great tracking device which is designed by Gosafe Company Limited. It combines GSM and
SMS with GPS to locate your belongs. As its compact size and long life battery, G626 can be easily
installed at somewhere concealed in your vehicle motorcycle and boat to track and locate them.
There are GSM modem, GPS receiver, control PCB, microprocessor, power circuit, rechargeable
battery and so on. Before starting G626 installation, please prepare one SIM card which works based
on GSM network that is offered by GSM mobile operating agency and can work with GPRS.
G626 is easy to install device even nonprofessionals can install this device. You only need to get
the valid data SIM Card. Disassemble the G626 and Insert the SIM card. The system have internal
movement sensor which controls the power management of the device. The power save mode
for G626 includes 9 types, which you can choose what you like. And also the working mode is
changeable. For further details, please refer to "Commands for device setting".
There are two covers of G626 for you to choose. One cover is normal cover, and another cover with
magnet.
Please note that if the G626 works at non-continue-working mode, you cannot make real-time
communication with the device if it is in sleep state. G626 will wake up and react by the operating
cycle you made.
G626 is equipped with highest available GPS uBlox modules and able to use A-GPS (Assist GPS)
technology to give help connecting the device with GPS faster with more accuracy.
1.1 Physical Appearance
Description Device Components Packing list
Pictures

Physical Specification
Power
MCU
GSM
GPS
Sensor
Memory
Environmental Conditions
Size
Weight
IP Rating
Rechargeable Battery
Power Consumption
MCU
Antenna
Modem
Frequency
GPRS
Approvals
LBS Location Accuracy
Antenna
Receiver
Channels
Sensitivity
Navigation update
Acquisition
Location Accuracy
3D G-Force Sensor
Flash
Operating Temperature
Storing Temperature
Humidity
86(L) x 60(W) x 25(H) mm
160g (Including Battery)
IP65
5V DC; Li-Ion 3.7V 3200mAh
Sleep Mode <700uA
Active Mode <300mA
TI MSP430 12KB RAM, 256KB Flash
Internal
uBlox LEON G100
Quad band 850/900/1800/1900MHz
Class 10 (4 downlink, 2 uplink, max.5)
Mobile Station Class B
AT&T, R&TTE, CE, GCF, FCC, PTCRB,
Anatel, IC, China SRRC, etc
100 to 500m (Urban)
0.5 to 30km (Suburb)
Internal
uBlox NEO 6M (GPS, & Sbase) engine
50 Parallel Channels
-162dBm
1sec
Cold Starts: 27s
Aided Starts: <1s
Hot Starts: <1s
2.5 to 10m (Strong Signals)
500 m (Weak Signals)
Onboard
10,000 Locations
-20℃ to +60℃
-20℃ to +60℃
100%
1.2 Specification
1.3 Features
· Geo-fence
· Real Time Location
· Mobile Map Location
· Latitude and Longitude Location
· GSM Base Station Location (LBS Technology)
· Rechargeable long lasting battery
· Dual Communication Modes (GPRS+SMS)
· Internal Movement Sensor
· Internal voltage detector to offer low voltage alert
· Internal memory for the data buffer

2.Quick Install Instructions
2.1Configuration
The G626 is supplied with USB cable. Connect the USB cable to the device and connect it with the
computer. The computer may require USB driver. It can automatically update the USB driver if not
then please download the USB driver from http://www.gosafesystem.com/downloads.aspand then
click on the G626 USB driver.
After downloading the USB driver update the USB driver and establish the connection between G626
and your computer.
Use the configuration software to configure. For further details, please refer to the documents for
configuration.
2.2 Insert SIM card
The user must arrange a SIM card with valid data plan. Before inserting the SIM card it must be
tested with your own mobile.
Insert the SIM card in your own mobile and try to send out SMS and receive SMS if it works fine
then try to connect to internet by opening any website in mobile browser.
Now you can disassemble the G626 by screwing off the four screws, which are used to fasten the
enclosure carefully, and then open the enclosure carefully. Insert SIM card into the SIM card jacket
correctly according to the below picture.
Note: Please do activate the SIM card, disable its PIN code function, and make sure
SIM card has enough balance before operating the device.
Each time before taking SIM card out of or inserting SIM card into the device, you
would better cut the power supply, or it would damage device and/or your SIM card.

2.3 Power on
Connect the battery to the device, like the below picture show you:
2.4 Installation Diagram for G626I
2.5 Set User No.
To set user No., you can use any mobile phone to send the following SMS command to the SIM card
No.: 1234,UNO;[phone] or 1234,UNO;13912345678
Explanations:
[phone]: user No. with country code
13912345678: user No. without country code
UNO: Command Control Word
After receipt of the above SMS command, device will reply a confirmation SMS and work at default
work mode: 30M;G;W
To protect device, if there is any error in this command, device will not send back any error warning.
2.6 Modify Password
To modify factory password at the first usage is strongly suggested. Password should be 4 digits that
picked from 0-9. To modify password, you can use user No. send the following SMS command to the
SIM card No.:
1234, UPW; 5678
Explanations:
1234: Factory Password
5678: New Password

Note: Please memorize your New Password and wait for confirmation SMS for
password modification from device.
Only if this command is sent by user No., the system can process this command.
2.7 Set Work Mode
There are 3 different work modes configurable for device according to user's need: O, S and G
Detailed information on 3 work modes, please go to "Commands for Device Setting" in this User
Manual.
Example:
To set device in G Work Mode, you should send the following SMS command to the SIM card No.:
****,UUM;30M;G;T
Explanation:
****: password
UUM: Command Control Word
G: the Work Mode user wants to configure
T: the type of message
3.Commands for Device Setting
All the commands for device setting in this User Manuel are in the same format:
user password+ command content
The command content is restricted to digits (0-9), English characters (a-z, and/or A-Z) and/or
common punctuations (Please check "Characters for Commands" table in Appendix), beyond which
device cannot recognize. If there is any character device cannot recognize, device will ignore it and
will not give any related warning to user.
All English control words in command could be capital words or lower case words.
3.1Set User No.
Command Format:
**** , UNO ; xxxxxxxxxx
**** , UNO ; +yyxxxxxxxxxx
Explanations:
****: user password (4-digit)
, : command delimiter
UNO: command control word
; : command delimiter
xxxxxxxxxx--telephone No. without country code
+yyxxxxxxxxxx--telephone No. with country code ("+") is country code mark while "yy" is country
code.
You can send SMS command to set or modify user No. through any mobile phone number.

No matter the telephone No. in command with or without country code, it is acceptable. Device will
reply a message for confirmation on after receipt of setting command to the set mobile phone, from
which the setting command was sent.
Example:
Setting command without country code in telephone No.: 1234,UNO;13912345678
Setting command with country code in telephone No.: 1234,UNO;[phone]
Reply:
G626 V1.05
UNO: 13912345678
Or
G626 V1.05
UNO: [phone]
3.2 Modify User Password
Command Format:
**** , UPW ; xxxx
Explanations:
****: user old password (4-digit)
, : command delimiter
UPW: Command Control Word
; : command delimiter
xxxx: user new password(4-digit)
Only if this command is sent by user No., the system can process this command. After password
modification successful, please do memorize your new password.
Example: 1234,UPW;5678
Reply:
G626 V1.05
UPW: 5678
3.3Set User Upload Mode, interval and type
Command Format:
**** , UUM ; xxS ; G ; T
Explanations:
****: user password (4-digit)
, : command delimiter
UUM: Command Control Word
; : command delimiter
xx: SMS interval
S: command control word (interval in Second, Minute, Hours)
;: command delimiter
G: Command Control Word (Mode)
;: command delimiter
T: Type of upload (Text, with hyperlink)

After receipt of this command, device will reply you a piece of message in UUM:30M;G;T SMS
Format. At each wakeup, device would send you a location report message in this format.
If device is in positive real-time work mode (upload operating cycle 00S or 00M or 00H), only one
piece of location report message will be sent by device; if updated location report is in demand
thereafter, please send another command then device will response accordingly.
Operating Cycle:
xxxS: Seconds upload range (30 ~ 900 seconds)
xxxM: Minute upload range (15 ~ 59 minutes)
xxxH: Hour upload range (1 ~ 240 hours)
Work Modes:
O: Cancel Upload
G: if there is GPS data, send GPS based location. If not, send GSM base station (LBS) data.
S: Always update with GSM base station (LBS)
Message Types:
T: Text format (SMS)
W: Text format with hyperlink (SMS with hyperlink)
Example: 1234,UUM;30S;G;T
Reply:
G626 V1.05
UUM:30S;G;T
3.4 Set Message Center Number
Command format
**** , SCN ; +XXXYYYYYYYYYYYYY
Explanations:
****: user password (4-digit)
, : command delimiter
SCN: Command Control Word
; : command delimiter
+XXXYYYYYYYYYYY: Message center number (XXX= country code, YYYYYYYYYYYY = center number)
After receipt of this command the device will reply with message SCN:+XXXYYYYYYYYY.
Example：
1234,SCN;[phone]
Reply:
G626 V1.05
SCN:[phone]
3.5 Set APN
Command format
**** , APN ; CMNET ; internet ; internet

Explanations:
****: user password (4-digit)
, : command delimiter
APN: Command Control Word
; : command delimiter
CMNET: Access Point Name (Confirm Access Point Name from the service provider)
;: command delimiter
internet: APN user name
;: command delimiter
Internet: APN Password
After receipt of this command the device will reply with message APN:access point name:APN user
name: APN password, the device will connects with GPRS after receiving this command. The G626
is equipped with many APN (Access Point Name) from many countries. If device automatically
connects with GPRS then user no need to send above command. If the device doesn’t connect with
GPRS then user may need to use APN command.
Example:
APN: cmnet, APN user name: internet, APN password: internet, command is: 1234,APN;cmnet;interne
t;internet
Reply:
G626 V1.05
APN:cmnet;internet;internet
If you only set the APN without the username and password
Example:
APN:cmnet, APN username: empty, APN password: empty, command is: 1234,APN;cmnet
Reply:
G626 V1.05
APN:cmnet;;
3.6 Power saving mode setting
Command format
**** , PSM ; 00
Explanations:
****: user password (4-digit)
, : command delimiter
PSM: Command Control Word
; : command delimiter
00: Parameter (The bigger the Parameters are, the lower power it will consume)
00: most performance mode, GSM and GPS both are available;
32: power save mode, the high 4 bits are GPS mode bits, the low 4 bits are GSM mode bits;

Composition of GPS mode bits:
0: Always on GPS (GPS ECO mode);
1: undefined, functions as GPS mode 0;
2: open GPS on demand, in reservation setting of GPS search time after 3D location , delay GPS work
time until reservation time is over;
3: open GPS module on demand, closing 3D location in reservation setting of GPS reach time, there
is no 3D location when GPS research time is over, closing module.
4: open GPS on demand, in reservation setting of GPS search time after 2D location , delay GPS work
time until reservation time is over;
5: open GPS module on demand, closing 3D location in reservation setting of GPS reach time, there
is no 2D location when GPS research time is over, closing module.
GSM mode consists of:
0: always on GSM;
1: open GSM module on-demand. (Open conditions: Getting LBS data, uploading data according to
setting and alarm occurred). Then upload all data. When alarm occurred, keep GSM module ON. If
there is no alarm, wait until the working time. if device received command during the working time,
recount the time. Close module when working time is up.
2: open GSM module on-demand. (Open conditions: Getting LBS data, uploading data according
to setting and alarm occurred). Then upload all data. Wait until the working time. If device received
command during the working time, recount the time. Close module when working time is up.
3: open GSM module on-demand. (Open conditions: Getting LBS data, uploading data according to
setting and alarm occurred). Then upload all data. If there is no alarm, close module immediately.
When alarm occurred, wait until the working time. If device received command during the working
time, recount the time. Close module when working time is up.
4: open GSM module on-demand. (Open conditions: Getting LBS data, uploading data according to
setting and alarm occurred). Then upload all data. Then close module.
5: open GSM module on-demand. (Open conditions: Getting LBS data, Uploading SMS data.
Uploading saved data according to setting and alarm occurred). Then upload all data. When alarm
occurred, keep GSM module ON. If there is no alarm, wait until the working time. if device received
command during the working time, recount the time. Close module when working time is up.
6: open GSM module on-demand. (Open conditions: Getting LBS data, Uploading SMS data.
Uploading saved data according to setting and alarm occurred). Then upload all data. Wait until the
working time. If device received command during the working time, recount the time. Close module
when working time is up.
7: open GSM module on-demand. (Open conditions: Getting LBS data, Uploading SMS data.
Uploading saved data according to setting and alarm occurred). Then upload all data. If there is no
alarm, close module. When alarm occurred, wait until the working time. If device received command
during the working time, recount the time. Close module when working time is up.
8: open GSM module on-demand. (Open conditions: Getting LBS data, Uploading SMS data.
Uploading saved data according to setting and alarm occurred). Then upload all data. Then close
module.

After receipt of this command the device will reply with message to confirm the work mode and
work as the setting.
Example:
Command is: 1234,PSM;32
Reply:
G626 V1.05
PSM: 32
3.7 Setting uploading TCP server mode
Command format
**** , TPM ; 30M ; G ; T
Explanations:
****: user password (4-digit)
, : command delimiter
TPM: Command Control Word
; : command delimiter
30M: Data save interval, M is time unit, it can be(5~900S)、(15~59M)、(1~240H)
;: command delimiter
G: unloading mode, it can be：
1. "O"/close unloading
2. "G"/ upload GPS data by internal set, when there is no GPS, data uploading based on base station
information
3. "S"/ data upload based on base station information
;: command delimiter
T: data format, it can be ：
1. B, means binary system;
2. T, means text
One Can set two modes. TPM is the same as TPM0, these two both are mode 0. TMP1 is mode 1.
Default: TPM0;60S;G;B
TPM1;1H;G;B
Example:
Command is: 1234,TPM;30M;G;T
Reply:
G626 V1.05
TPM: 30M;G;T
3.8 Enable/Disable Over speed alarm
Command format
**** , SPO ; M
Explanations:
****: user password (4-digit)
, : command delimiter

SPO: Command Control Word
; : command delimiter
M: Parameter (1=Enable, 0=Disable)
After receipt of this command the device will reply with message SPO:M, device would enable/
disable over speed alarms. If enable the device, it will send SMS to user mobile according to the
setting of over speed limit. If disable it will not detect the over speed limit.
Example：
Enable over speed alarm, command is: 1234,SPO;1
Disable over speed alarm, command is: 1234,SPO;0
Reply:
G626 V1.05
SPO:1
Or
G626 V1.05
SPO:0
3.9 Movement sensor setting
Command format
**** , MTP ; 600
Explanations:
****: user password (4-digit)
, : command delimiter
MTP: Command Control Word
; : command delimiter
The range of three parameters is the same: that is: 1 ~ 1800.
"600": sustained stop time. Unit is second. This parameter is used to judge whether the vehicle status
is shift from stop status to move status.
Default: 600
Example：
Command
1234, MTP;600
Reply:
G626 V1.05
MTP:600

3.10 Enable/Disable Over Speed Alarm Parameter
Command format
**** , SOP ; Alert Speed ; Alarm Speed
Explanations:
****: user password (4-digit)
, : command delimiter
SOP: Command Control Word
; : command delimiter
Alert Speed: set the speed in KM/H (80 km/h) (G626 can't provide this function at this moment)
; : command delimiter
Alarm Speed: set the speed in KM/H (100 km/h)
After receipt of this command the device will reply with message SOP:Alert speed; alarm speed, The
Alert speed is the speed when the system start testing the over speed and send the alert first. If the
device crossed the alarm speed limit it will send the alarm.
Example:
Alert speed = 80
Alarm speed=100
Command
1234,SOP;80;100
Reply:
G626 V1.05
SOP: 80;100
3.11 Enable/Disable SMS when movement trigger
Command format
**** , MOT ; M
Explanations:
****: user password (4-digit)
, : command delimiter
MOT: Command Control Word
; : command delimiter
M: Parameter (1=Enable, motion sensor set as low sensibility; 2=Enable, motion sensor set as high
sensibility, 0=Disable)
After receipt of this command the device will reply with message MOT:M, device would enable/
disable the SMS to user mobile when movement is sensed by movement sensor.
Example:
Enable SMS upload (motion sensor set as low sensibility) when movement trigger, command is:
1234,MOT;1
Disable SMS upload when movement trigger, command is: 1234,MOT;0
Note: The device will automatically send location SMS to the user once it will sense
any movement. The device will send only one SMS at the start of the movement.
Device will wait for the vehicle to stop and will start the counter to 60 min. If the
movement is after 60 min. device will again send the SMS to the user mobile.

3.12 Location Poll
There are two ways to poll the location from the device.
1. By sending PQR SMS to device:
**** , PRQ
****: user password (4-digit)
, : command delimiter
PRQ: Command Control Word
Example:
1234,PRQ
Reply:
G626 V0.17
PRQ
The device will send back the location informat-ion after getting the latest GPS data.
G626 V0.17
GPS 5/67
UTC 11-05-11 06:47
N23.164367
E113.428548
SPD:0km/h
TMP:37.8C
PWR:10.5V
2. The user mobile can call to the device number and hangup after first ring. The device will send
back the GPS location to the user mobile.
G626 V0.17
GPS 5/67
UTC 11-05-11 06:47
N23.164367
E113.428548
SPD:0km/h
TMP:37.8C
PWR:10.5V
3.13 Set Time Zone
Command format
**** , TZN ; Time Zone
Explanations:
****: user password (4-digit)
, : command delimiter
TZN: Command Control Word
; : command delimiter
Time Zone: Enter the time zone parameters -12:00 to 12:00

After receipt of this command the device will send back TZN:Time zone. After receiving this
command the device will send the local time in the SMS if the gps data is valid. If there is not GPS
data device will not send the time.
Example:
Time zone= +8
1234,TZN;8:00
Reply:
G626 V1.05
TZN:8:00
Time Zone= -5
1234,TZN;-5:00
Reply:
TZN:-5:00
3.14 Clear Alarm
Command format
**** , UAC
Explanations:
****: user password (4-digit)
, : command delimiter
UAC: Command Control Word
After receipt of this command the device will send back UAC. It will clear the user alarm and device
will not send the user alarm.
Example:
1234,UAC
Reply:
G626 V1.05
UAC
3.15 Query SIM card balance
Command format:
**** , BLC , XXXX
Explanations:
****: user password (4-digits)
, command delimiter
BLC: Command Control Word
, command delimiter
XXXX is command which is provided by GSM service.
We use USSD to query the balance of SIM card, sending the command, and then waiting for 2 to 3
minutes. The device will reply balance information to user or control center.
3.16 Commands Wait
In the event of there come commands from user when device is in sleep and couldn't process
commands, at each wakeup device will wait one minute to receive those commands and take
precedence to process them then response one confirmation message; after 1 min, device would
receive and process real-time commands then reply accordingly.

3.17 Alarms
The device sends alarm immediately it triggers. The message receive when device is in alarm as
follows:
G626 V1.05
GPS 6/77
UTC 11-00.5-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Low inter_Batt
SMS Received
G626 V1.05
GPS 6/77
UTC 11-05-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Low inter_Batt
G626 V1.05
GPS 6/77
UTC 11-05-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Over Speed
G626 V1.05
GPS 6/77
UTC 11-05-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Moving
G626 V1.05
GPS 6/77
UTC 11-05-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Geo-Fence
G626 V1.05
GPS 6/77
UTC 11-05-14 05:33:47
N23.164479
E113.428606
SPD:0km/h 0
Alarm:
Anti-Jamming
Description
Low Power
Over Speed
Moving (When the vehicle I stopped and the movement sensor is
enable the device sends move alarm on the trigger of movement
sensor)
Geo-Fence (Future use the current version firmware don't support it)
Anti-Jamming (This alarm appear if the anti-jamming feature is
enable and the someone use GSM jammer near the device)
List of Alarms:

Note: The user can use the UAC command to clear user based alarm.
3.18 Default Parameters
Device is set with the following default param-eters. When device power up first time the device will
use the following parameters to connect and wait for user commands or server commands.
3.19 Combine Command
To save time and SMS resource on configuration, user can apply combine command, in which there
is more than one command, to operate configuration. The combine command would begin with
user password, which is followed by commands (commands order is flexible).
Format is as follow:
Description
User number
SMS center number
PIN code of SIM
APN list
User password
User upload mode
Manager phone number
Manager upload mode
Server IP or domain name
TCP port
UDP port
TCP channel upload mode (mode 0)
UDP channel upload mode (mode 0)
PSM
Package number of per TCP upload
Package number of per UDP upload
percentage of data buffer per TPC upload
percentage of data buffer per UDP upload
Over speed
Enable/ disable over speed alarm
Enable/disable vibration sensor
Enable/disable anti-jamming
Time zone
Vibration sensor parameter
Anti-jamming parameter
Baud rate of extend serial port
Transmit mode of extend serial port
USB port mode
Supper link (0) GPS Link
Supper link (1) (LBS Link)
Phone list of SMS forwarding
Hot line list
Time for talking
SMS number counter
Parameter
(EMPTY)
(EMPTY)
1234
APN list of Russia only
1234
24H;G;W
(empty)
30M；G；T
domain name (empty)
IP (114.142.154.28)
3032
3032
60S；G；B
30S；O；B
00
1
1
1
1
80；100
Disable
Disable
Disable
0:00
MOT0: Disable
MOT1: 10,10
MOT2: 5,5
30；20
9600
Common mode
Common mode
Yandex map link
(empty)
(empty)
(empty)
0；0
0；0

If there is duplication of the same command in the same combine command, just the last piece of
command would be processed; if there is error in the command, the command with error would be
discarded, and device would only confirm setting of correct commands with no error warning. If all
the commands are error, an alarm will be sent.
All setting commands, except user No. setting command under the condition of the user number
has never been changed, can be set by combine command.
Example: 1234,UUM;30M;G;T,UPW;1234
4.Structures of SMS from Device
4.1Normal Location SMS Format (G Mode)
(Located Successful)
Gosafe G626 V1.05
GPS 3/56
LTM08:00 11-24-10 02:54
N23 9.8329
E113 25.7149
Speed: 1km/h 39
TMP=25.6C
PWR=12.5V
Gosafe G626 V1.05
MCC=460
MNC=1
LAC=517A
CID=1FB1
TMP=25.6C
PWR=12.5V
(Located Unsuccessful)
Gosafe G626 V1.05
MCC=460
MNC=1
LAC=517A
CID=1FB1
TMP=25.6C
PWR=12.5V
Device Name and Version
Satellites Connected &Time used for Location (secs)
Specific time zone and Location time based on specific time zone
Latitude in degree-minute format
Longitude in degree-minute format
Device speed and Move Direction
Temperature
Power
Device Name and Version
Mobile Country Code
Mobile Network Code
Location Area Code
Cell Identity
Temperature
Power
Device Name and Version
Mobile Country Code
Mobile Network Code
Location Area Code
Cell Identity
Temperature
Power
Gosafe G626 V1.05
http://maps.google.com/staticmap?zoom=14&size=150x150&m
arkers=39.9493,116.3875&sensor=false
TMP=25.6C
PWR=12.5V
4.2 Hyperlink SMS Format (W Mode)
(Located Successful）Google link
Device Name and Version
Google Map Link
Temperature
Power
Pw , Command ; Parameter ; Parameter , Command ; parameter
word word
First command Second Command

4.3 Error Command Alert
Gosafe G626 V1.05
Error command!
4.4 Password Modification Successful
Confirmation
Gosafe G626 V1.05
UPW:5678
4.5 User No. Setting Successful Confirmation
Gosafe G626 V1.05
UNO:[phone]
4.6 Command Table
The user command is shown in the below table. The whole command format is "PSW,CMDXX;Para".
Table only show the second part "CMDXX;Para" in the column of command format.
User Command List
(Located Unsuccessful)
Gosafe G626 V1.05
MCC=460
MNC=1
LAC=517A
CID=1FB1
TMP=25.6C
PWR=12.5V
Device Name and Version
Mobile Country Code
Mobile Network Code
Location Area Code
Cell Identity
Temperature
Power
Gosafe G626 V1.05
http://m.maps.yandex.ru/?ll=116.3875,39. 949328&pt=116.3875,
39.949328&z=12
TMP=25.6C
PWR=12.5V
(Located Successful）Yandex link
Remarks
0~20 bits, default is empty
①set national number
②set international number,
"86" is country number
Four bits,range:0000~9999
30M：upload interval, M can
be(30~900S)、(15~59M)、
(1~240H)
Default:30m;G;W
G: upload mode, it can be:
"O"/close uploading
"G"/upload GPS data by
interval set, when there is no
GPS, data uploading based
Reply
①UNO:13912345678
or
②UNO:[phone]
UPW:1234
UUM: 30M;G;T
Command
①UNO;13912345678
or
②UNO;[phone]
UPW;1234
UUM;30M;G;T
Ctrl Word
UNO
UPW
UUM
Description
Setting user
phone number
Setting user
password
Setting users to
upload mode
Sr.
1
2
3
Device Name and Version
Yandex Link
Temperature
Power