GR GR6EUO User manual

Questions – [e-mail]
Page 1
LOGICID120
•TIP– You need to fit three small loops of wire to your safety inputs to make anything work. These
can be removed later if you install safety devices to these input terminals. But for now take three
pieces of light gauge wire (speaker or telephone wire is good) about 50mm long and strip both ends
7mm and insert them as above from 6 to 9, 8 to 9 and 12 to 13.
•TIP – The manual offers both automatic programming and manual programming. Manual
programming gives more control and is preferred by professional installers, but auto programming
works just fine so give it a try first.
•TIP – This control board has a higher level of security than previous versions and will not accept
older style remote controls. Use REMGR only.
•TIP – If using wireless keypad KEYPADP6 set it to 20Bit mode to work with this board.

GR
GRGR
GR6
66
6–
––
–8
88
8EUO
EUOEUO
EUO
G.R. SISTEMI AUTOMATICI DI APERTURA SRL
MOTOR FOR SLIDING GATES
MOTOR FOR SLIDING GATESMOTOR FOR SLIDING GATES
MOTOR FOR SLIDING GATES

INSTALLATION MANUAL
Our compliments for your excellent choice. The GR6-8 electro-
mechanical gear motor has been produced for reliability and high quality.
This Manual will offer information you may need to install your gear motor
assuring long-lasting performance and to safeguard your safety.
HOWEVER CAUTION IS UNQUESTIONABLY INDISPENSABLE AND
NOTHING IS BETTER THAN PREVENTING ACCIDENTS. GR products
have been made to conform with rules and laws in force at time of
manufacture.
This manual is designed exclusively for the specialized installation
expert in the criteria of construction and equipment to assist in the
protection against accidents in the installation and use of the gate; door
and automation of such gates (adhere to the rules and laws in force).
On completion the installer should issue to the end consumer an
instruction manual according to EN 12635.
Before proceeding with the installation the installer must provide an
analysis of the identification and management of risks as per the
standards EN 12453 and EN 12445.
All wiring of the various external electrical components connected to
the automation (e.g. Photocells, flashing lights, keypads etc) must be
carried out according to EN 60204-1 and the amendments made of the
point 5.2.2 of EN 12453.
It is prohibited to do any repair or adjustment of the equipment if you
have not taken all necessary precautions to avoid possible accidents
(example: power supply disconnected, engine block). All mechanisms in
motion must be equipped with appropriate protections.
The mains power line must be protected for maximum current in
locked rotor condition as per government electrical laws.
Install the gear motor on gates that conform to EN 12604.
Perform the measure of strength developed by the gear motor and
take the appropriate steps as per EN 12445.
Positioning photocells: These safety devices must be installed at a
height not exceeding 70cm from the ground and at a distance from the
floor movement of the door of no more than 20cm. Their proper
functioning of the photocells must be verified at the end of installation
according to Section 7.2.1 of EN12445.
Keep the activation controls of automation out of reach of children.
The controls should be installed at a minimum 1.5m height above the
ground and outside the range of actions of moving parts such as the
gate.
All activation actions must be executed only at points from where
the automation is fully visible.
Operate the remote only in view of automation.
Store carefully this manual in a suitable place known to all
interested people.
Any unauthorized and arbitrary modification made to this product,
releases the company GR SISTEMI AUTOMATICI DI APERTURA Srl
and from any liability resulting from damage or injury to things, people or
animals.
The non-observance of regulations and of safety standards here
listed releases the company GR SISTEMI AUTOMATICI DI APERTURA
Srl from any liability resulting from damage or injury to things, people or
animals.
The automation must be coupled to a control board equipped with
torque regulation that provides an anti crushing safety as described in EN
12453 - EN 12445
CONFORMITY DECLARATION:
It’s in accordance with Machine Directive 39/89/CE and following modify.
It’s in accordance with the following directive CE:
Electromagnetic compatibility Directive 89/336/CEE and following modify.
Low tension Directive 73/23/CEE and following modify.
Have been applied the following harmonized norms:
EN292/1/2, EN 294, EN60335-1, UNI EN 12453, and what applicable of
the EN12445-2000.
Castiglione d/St. 05-10-2020
DISMANTLING / REINSTALLING
This product falls within the scope of the Directive 2012/19 / EU
concerning the management of waste electrical and electronic equipment
(WEEE). The appliance must not be disposed of with domestic waste as
it is made of different materials that can be recycled at the appropriate
facilities. Inquire through the municipal authority regarding the location of
the ecological platforms to receive the product for disposal and its
subsequent correct recycling. Furthermore, it should be remembered
that, upon purchase of an equivalent appliance, the distributor is obliged
to collect the product for disposal free of charge. The product is not
potentially dangerous for human health and the environment, not
containing harmful substances, but if abandoned in the environment
negatively impacts on the ecosystem. Read the instructions carefully
before using the appliance for the first time. It is recommended that you
do not use the product for any purpose other than that for which it was
intended, there being a danger of electric shock if used improperly.
The crossed-out bin symbol, on the label on the appliance,
indicates the compliance of this product with the
regulations regarding waste electrical and electronic
equipment. Abandonment in the environment of the
equipment or illegal disposal of the equipment is
punishable by law.
To dismantle or reinstall the automation elsewhere, you need to:
1 - Disconnect the power supply and disconnect the electrical system.
2 - Remove the control panel and all the components of the installation.
In the event that some components are damaged or unable to be
removed, replace them.
SAFETY RULES
During the installation and the use of the automation, pay attention to the
following safety rules:
Distance security!
Mechanisms moving!
Do not install automation in an environment saturated with explosive
mixtures!
Electric Shock!
Use gloves!
Use welding glasses!
Maintain ear protection!
USE OF THE AUTOMATION
The gearmotor GR6-8 was designed and built for the opening of gates
with weight max. 800kg. G.R. Srl assumes no responsibility for a
purpose other than that provided by gearmotor GR6-8. Since automation
can be put into motion in view by button or remotely by remote control, it
is essential to check frequently the perfect efficiency of all safety devices.
It is advisable to check periodically (every six months) the regulation of
electronic friction of which must be equipped the electronic control board.
TECHNICAL DATA
GR6 220V GR8 220V
MAX. weight of the gate
600Kg 800Kg
Power supply
220Vac 220Vac
Nominal power
190W 350W
Capacitor
8,0µF 12,5µF
Absorption
1,1A 1,5A
RPM
1400 1400
Torque
13,4Nm 21,2Nm
Gate speed
10,2m/min 10,2m/min
Thermal protection
150°C 150°C
Working temp.
-20°C +60°C -20°C +60°C
Lubrication
GREASE GREASE
Protection IP
IP44 IP44
Use frequency
25% 35%

PRELIMINARY CHECKS
– Read the instructions in the manual carefully.
– Check that the gate is perfectly horizontal
– Check that it slides smoothly and without friction points
–
Check that there is an adequate base for fixing the motor, otherwise
prepare it
– Check that the electrical system complies with the characteristics
required
by the gearmotor
The gearmotor is delivered UNLOCKED
– Remove the motor from the box, check that it is not damaged. Unscrew
the screws A and B and remove the cover FIG.1
INSTALLATION
A = 105mm = VERTICAL DISTANCE BETWEEN THE TEETH OF
THE RACK AND THE GROUND
B = 20mm= HORIZONTAL DISTANCE BETWEEN THE DRIVE
WHEEL AND THE GATE
C = 55mm = HORIZONTAL DISTANCE BETWEEN THE BASE OF
THE MOTOR AND THE GATE
FOUNDATION PLATE (OPTIONAL)
If the base has yet to be prepared and the installation of the motor is
not immediate, it is possible to cement the foundation plate (NOT
INCLUDED) following the installation dimensions FIG.2
– Position the foundation plate as shown in FIG. 3
GEARMOTOR POSITIONING
If there is a concrete base already prepared, it is possible to install the
motor, without using the foundation plate, following the installation
dimensions in FIG. 2. In this case, suitable M10 screw anchors must
be used
– Position the motor so that the cable outlets correspond to the
appropriate holes on the motor body. FIG. 4
– Secure the motor to the ground with suitable anchors, using the
slots provided FIG. 5.
Or if the foundation plate is installed, fix the motor to the 4 log bolts
provided as shown in FIG.3.
A
B
FIG. 3
C
325
mm
288
mm
72
mm
155
mm
125
mm
FIG. 2
FIG.1
FIG.4
1,0mm
FIG.5

INSTALLING THE RACK
If the rack is already installed, check that there is a space of
approximately 1mm between the drive wheel and the rack FIG.5,
if the rack is not installed, proceed as follows:
–Take the first piece of rack and position it on the motor sprocket
making sure that at the end of the installation there is always 1mm of
space (if necessary use temporary shims under the motor). Slide it to
the point indicated in FIG. 5
– Weld or screw the first pin or spacer to the gate (depending on the
type of rack).
– Apply all the other elements of the rack so that they are perfectly
joined and aligned with the first one. Use pliers and a piece of rack for
perfect alignment of one element with the other. See FIG. 6
EMERGENCY RELEASE
To unlock the motor proceed as follows:
– remove the cap D
– Insert the supplied key E and turn CLOCKWISE for 4 turns FIG.7
– To overturn the motor turn ANTICLOCKWISE for 4 turns
FINAL OPERATIONS
Once the rack and motor have been fixed, release the motor see
FIG.8, and move the gate to check that it slides freely and effortlessly.
ATTENTION vérifier qu'il ne "repose" pas sur la roue motrice du
moteur. Dans ce cas, réglez la crémaillère pour laisser environ 1 mm
d'espace entre le pignon du moteur et la crémaillère
– Install the limit switch cams on the rack FIG. 8 without fixing them in
a definitive way, in order to be able to adjust them in the optimal
position when programming the control unit.
CAUTION The limit switch cams are used to operate the limit
switches of the motor which, by means of the control unit, interrupt the
movement of the gate during opening and closing. They must be
positioned at the ends of the rack taking into account any inertia and
the delay in stopping the gate with respect to the operation of the limit
switches.
– Proceed with the electrical connections, program the control unit,
carry out the final test and reinstall the cover cards.
SCHEDULED MAINTENANCE WARNINGS
Before any maintenance operation, disconnect the power using
the main switch
The equipment must be maintained in such a way as to maintain
the conditions that guarantee safety and correct operation
Always use original spare parts
Do not carry out any interventions that modify the machine
The modified machine needs a new CE mark
The adjustment of the function of the automation must be carried
out by specialized personnel, in compliance with the relevant
regulations. During these operations the presence of two operators is
expected
SCHEDULED MAINTENANCE - OPERATIONS
DESCRIPTION FREQUENCY ENTRUSTED OPERATION
Photocells cleaning Monthly Operator Clean with damp cloth
Control of the gate supports of the fall arrest
devices, the limit stops, the rack, the sliding
guide and the sliding of the gate
According to
necessity
Operator Check the integrity of all items, state of welds and
corrosion. Unhook the motor and check the friction
points of the gate and the distance between the
pinion and rack (1.0mm).
Control of the sensitivity of the electronic
clutch (torque regulation) of the control unit
Semiannual Technician Check the torque adjustment as indicated in the EN
12453 - EN 12445 standard
Control of the IP protection Semiannual Technician Check that there are no traces of moisture or water
inside the electrical enclosures
Monitoring current dispersion Annual Technician Verify that the dispersion of current is less than 7.5 A
Control of signals Semiannual Operator Verify that the safety warning signage is complete
and intact
FIG. 5
FIG. 6
FIG.8
D
4 TURNS
CAUTION DO NOT RE-LOCK THE MOTOR WHILE
IT‘S RUNNING
FIG.7
E

Mod. IO31/E - rev. 00
ID 120
CONTROL UNIT FOR 1 MOTOR 220V
Important: Read carefully this manual before the installation. This manual is integral part of your
product, keep it for reference.
Warnings:
First of all verify that this product is suitable for the installation.
Read carefully technical characteristic before the installation.
Installation of this control unit must be properly done by qualified installers, following rules and regulations of
installation country.
It's mandatory do periodic maintenance each 6 month.
Maintenance or repairing must be done by qualified Technicians.
Turn power off before maintenance or repairing.
This device is intended for gate automation, any other applications is strongly advised.
Not respecting of rules may cause serious damage to peoples, animals, things.
Manufacturer discharges all responsibility for missed respect of rules.
Don't let this control unit unattended or where children can reach
Preliminary checking: Before to install this control unit,
Verify that all the connected devices respect the technical characteristics mentioned in the table which follows.
Verify that a working and suitable life switch is installed upline the installation.
Verify that cables composing the installation, are suitable for it.
This product falls within the scope of the Directive 2012/19 / EU concerning the management of waste electrical
and electronic equipment (WEEE). The appliance must not be disposed of with domestic waste as it is made of
different materials that can be recycled at the appropriate facilities. Inquire through the municipal authority regarding
the location of the ecological platforms to receive the product for disposal and its subsequent correct recycling.
Furthermore, it should be remembered that, upon purchase of an equivalent appliance, the distributor is obliged to
collect the product for disposal free of charge. The product is not potentially dangerous for human health and the
environment, not containing harmful substance
s, but if abandoned in the environment negatively impacts on the
ecosystem. Read the instructions carefully before using the appliance for the first time. It is recommended that you
do not use the product for any purpose other than that for which it was intended, there being a danger of electric
shock if used improperly
The crossed-out bin symbol, on the label on the appliance, indicates the compliance of
this product with the regulations regarding waste electrical and electronic equipment.
Abandonment in the environment of the equipment or illegal disposal of the equipment
is punishable by law.
The manufacturer:
Declares: The control unit ID120 is compliant to following
directives:
- 2006/95/CE Low voltage directive.
- 2004/108/CE Electromagnetic compatibility.
Castiglione 10-11-2020
Castiglione 10-11-2016
TECHNICAL DATA
Power supply
230Vac +/- 10%
Consumption
800mW (stand-by)
Auxiliary supply out
24Vac, 200mA
Motor output
230Vac, 800W
Flashing light output
230Vac, 100W
Courtesy light output (AUX)
230Vac, 100W
Operating temperature range
-10 +60°C
G.R. SISTEMI AUTOMATICI DI APERTURA S.R.L.

1
Antenna’s shield
18 – 19
Motor capacitor
2
Antenna
20
Motor output - OPEN
3
Input OPEN / START (NO) – see menu OL
21
Motor output - CLOSE
4
Input CLOSE / PEDESTRIAN (NO) – see menu OL
22
Motor output - COMMON
5
Common
23
Earth connection
6
Photocell input (NC - NO) see advanced menu PC
During the pause: Reload the pause time
During closing: Reverses the motion of the motors
24 – 25
AC Power connection 230V
7
DETECT quick closing input (NO)
26 – 27
Courtesy light (25-26) / red-green traffic light
control (see advanced menu CR)
8
PHOTOSTOP / PROTECTION input (NC / NO see
advanced menu Pt )
28 - 29
AC power out 24V– 250mA
9
Common
TR1
Slowdown speed adjustment
10
Limit switch Open input (NO/NC, see advanced
menu L5) If both limit switches open they are
disabled.
TR2
Motor power adjustment
11
Limit switch Close input (NO/NC, see advanced
menu L5) If both limit switches open they are
disabled.
TR3
Slowdown time adjustment
12
Stop input (NO/NC, see advanced menu 5P)In
every operation it blocks the gate.
TS1- TS3
Buttons UP/DOWN
13
Common
TS2
ENTER button
14 – 15
Output positive / negative 12Vdc – 250mA
DSP
Display
16 – 17
Blinker with two working modes (see advanced
menu BL)
F1
230Vac outputs fuse, 5A Fast
88
TR1
SD SPEED
TR2
FORCE
TR3
SD TIME
F1

INPUT STATUS
When the board is in standby, the status of the inputs is shown on the display:
--
NO INPUTS ACTIVE
5T
START INPUT ACTIVE
5P
STOP INPUT ACTIVE
PD
PEDESTRIAN INPUT ACTIVE
PT
PROTECTION INPUT ACTIVE
OP
OPEN INPUT ACTIVE
P5
PHOTOSTOP INPUT ACTIVE
CL
CLOSE INPUT ACTIVE
PC
PHOTOCELLS INPUT ACTIVE
FC
LIMIT SWITCH CLOSE
DT
DETECT INPUT ACTIVE (QUICK CLOSE)
FO
LIMIT SWITCH OPEN
ATTENTION: During pause, the display show the seconds countdown to closing.
If Mass mode is selected (see advanced menu), display show the number of entrance allowed.
TRIMMERS
TR1 SD SPEED - Regulates the slowing down speed.
TR2 FORCE – Regulates the obstacle detection sensibility from 0% to 100%. ATTENTION: during the first 2 seconds of
running the control unit gives 100% of the power to the motor (starting power)
TR3 SD TIME –Regulates the slowing down lasting from 0 to 10 seconds (about)
SLOWER FASTER
TR1 SLOWING DOWN SPEED
LESS
TORQUE
MORE
TORQUE
TR2 OBSTACLE DETECTION
SENSITIVITY
0 sec. 10 sec
TR3 SLOWINGDOWN LASTING
SPECIAL FEATURES:
SELF PROGRAMMING
This board in most chases doesn't need any working time programming to work. If the working time hadn't been
programmed, at each first complete opening (from closing limit switch to opening limit switch.) after a power reset the board
will calculate itself a value for the current gate and sets the slowing down starting from next closing. This self-learned setting
can be deleted by resetting the board or by programming the working time.
QUICK PROGRAMMING
To quickly program the working times, keep pushed up till you read LT on the display (3 seconds). If the gate/barrier isn't
fully closed, it will close till the limit switch, then it will open to the Opening limit switch, and finally it closes once.
Attention: if you aren't sure about gate/barrier direction, set it in fully closed position before to start programming, the
board will assume the engaged limit switch as closing side, and will manage motor direction automatically (see “GD”
menu in advanced menu)
QUICK LEARNING OF REMOTE CONTROLS
Briefly press the down key (C1 appears on the display), then transmit a start / open command.
To enter a pedestrian command / close, briefly press the down key twice (C2 appears on the display).
To enter a command to switch on the courtesy light, briefly press the down key (on the display) 3 times C3 appears).
Auto Learning transmitters:
It's possible to learn transmitters quickly without using the base menu. To insert a new transmitter, transmit 3 times with
the new remote, making at least 1 second pause between each transmission. Then transmit 3 times with a transmitter
already in memory and then once with the new. When programming is done, the stop led on the keyboard flash once.
Attention: This function must be enabled, refer to “advanced menu AR”.
MASS ENTERING MODE
In this mode, if you push 5 times Open command (example), the control unit count 5 cars passing through the detect
sensor, then it closes the barrier. This mode must be enabled in advanced menu (MM). This mode can be enabled just
when automatic closing is disabled.
USE OF UP, MODE AND DOWN BUTTONS FOR PROGRAMMING
Control unit function programming is made within a special configuration menu, to which you can access and where you can
shift through DOWN, MENU and UP keys placed under the display. The configuration menu consists in a list of configurable
items; the display shows the selected item.
• By pressing DOWN, you will pass to the next item
• By pressing UP, you will return to the previous item
• By pressing together UP and DOWN buttons you exit from the function
• By pressing MODE, you can view the current value of selected item and possibly change it.
There are 2 main menus:
- BASE PROGRAMMING: only the useful parameters for a base programming are displayed.
- ADVANCED PROGRAMMING: parameters of the advanced menu are displayed.
UP
ENTER
DOWN

BOARD PROGRAMMING
BASE MENU
Push enter button shortly to enter base menu. Ol is displayed, with up/down it's possible to select other functions of this
menu. To exit this menu select EX or push up and down together. After 20 seconds without actions, control unit exits itself
from this menu.
BASIC MENU SCHEME
1 SEC.
oL Operating logic
5T
Step by step mode: inputs 3 & 4 works as
Start and Pedestrian start.
At
Step by step mode with auto closing: inputs 3
& 4 works as Start and Pedestrian start.
CD
Condominium mode: inputs 3 & 4 works as
Start and Pedestrian start.
Oc
Open/Close mode: inputs 3 & 4 works as Open
and close.
oa
Open/Close mode with auto closing: inputs 3
& 4 works as Open and close.
EX
EXIT or push together
LC Radio code learning
C1
Learn Start / Open command (according to Ol
menu).
C2
Learn Pedestrian / Close command (according
to Ol menu).
C3 Learn Courtesy light (see advanced menu LX).
ra
Remove all codes
EX
EXIT or push together
LC LEARN RADIO CODE - Select LC and push enter, with up/down select sub menu.
C1: Learns a remote. Select this menu and transmit to learn a Start/Open command.
C2: Learns a remote. Select this menu and transmit to learn a Pedestrian/Close command.
C3 : Courtesy light activation
RA: Remove all codes, select this menu, than select Y5 (yes) in the next menu to remove all codes.
LT Working times
learning
AU Automatic learning procedure
EX EXIT or push together
LT EARN WORKING TIME - Select LT in the base menu and push enter, after select the learning mode with
up/down. The gate/barrier closes till the closing limit switch, then it opens to the Opening limit switch, and
finally it closes once.
ATTENTION:
if you aren't sure about gate/barrier direction, set it in fully closed position before to start
programming, the board will assume the engaged limit switch as closing side, and will manage motor direction
automatically (see “GD” menu in advanced menu).
To stop Learning procedure, switch Stop input.
5P Set pause time
0 –99
5P SET PAUSE TIME - Use up/down to set the pause time between 0and 99 seconds. Push enter to confirm. To
EXIT without modifications, push together up and down.
DM Dead man mode
OP Open motor
CL Close motor
EX EXIT or push together
DM DEAD MAN MODE. By selecting this menu it is possible to move the gate in dead man mode:
O1: Gate opens, press and hold ENTER in this menu to move the gate in dead man mode.
C1: Gate closes, press and hold ENTER in this menu to move the gate in dead man mode.
EX EXIT

ADVANCED MENU
Keep enter button pushed till on the display is shown TM (almost 4 seconds). With up/down it's possible to select all items in
this menu. To exit this menu select EX or push up/down together. After 20 seconds without actions, control unit exits itself
from this menu.
ADVANCED MENU SCHEME
4 SEC.
tm Working times menu
T1 Working time
0 –99
TP Pedestrian time
tc Courtesy light time (x 10 sec)
ex EXIT or push together
tm Working times menu:
In this menu it's possible to modify working times of control unit:
T1 – Working time
tp – Pedestrian time
tc – Courtesy light time (in ten of seconds)
EX – Exits from advanced menu
Once selected working time to be changed, use up/down to modify it from 0to 99 seconds. Push enter to
confirm.
To exit without modifications select ex or push together up and down.
gd Gate direction
Rh Gate direction right
Lf
Gate direction left
ex EXIT or push together
GD GATE DIRECTION - Set if direction of the gate is right (RH) or left (LF). Use up/down to choose, ENTER to
confirm.
PC Photocell input
polarity
No Normally open
nc Normally close
ex
EXIT or push together
PC PHOTOCELL INPUT POLARITY - Set if photocell input is NO or NC. Use up/down to choose NO (NO), NC (NC) or
exit (EX). Push ENTER to confirm.
pt Photostop/Protection
mode
No Normally open
nc
Normally close
ex EXIT or push together
PT PHOTOSTOP / PROTECTION INPUT POLARITY - Set if Photostop/Protection input is NO or NC. The PT input
works as Photostop (P5) if Sliding gate mode is selected, while it works as Protection (PT) when the barrier mode
is selected (see advanced menu BR).
P5 – Photostop Mode (NC): During closing it stops the gate while this input is engaged, on release the gate
opens. Photostop input during opening it stops the gate till the command it's released. After a photostop
command the next direction is always opening.
PT – Protection mode (NO): While closing, Protection command reverses opening completely. In opening phase
Protection command is ignored. The gate can't close while Protection command is engaged.
5p Stop input polarity
No
Normally open
nc
Normally close
ex
EXIT or push together
5P STOP INPUT POLARITY - Set if Stop input is NO or NC. Use up/down to choose NO (NO), NC (NC) or exit (EX).
Push ENTER to confirm.

L5 Limit switches
polarity
No
Normally open
nc Normally close
ex
EXIT or push together
L5 LIMIT SWITCHES POLARITY - Set if L5 are NO or NC. Use up/down to choose NO (NO), NC (NC) or EXIT (EX).
Push enter to confirm.
Pr Motor power in fast
speed
0 - 10
ex EXIT or push together
PR MOTOR POWER IN FAST SPEED - Set the motor power (fast speed) between 1(10%) and 10 (100%).
pl Motor power in
slowing down
0 - 10
ex
EXIT or push together
Pl MOTOR POWER IN SLOWING DOWN - Set the motor power (slowing down) between 1 (10%) and 10 (100%).
55 Soft start
Y5 Enabled
Nt Disabled
ex
EXIT or push together
55 SOFT START - Set if soft start is active (Y5) or not (NT). Soft start make a linear power slope to avoid mech
shoks at start.
bl Blinker mode
Y5
Enable blinking
Nt
Disable blinking (for flashing lights equipped
with a flashing board)
ex EXIT or push together
BL BLINKER MODE - Set if blinker output works as blinker, or as semaphore signal. Use up/down to choose
blinker mode (Y5), Semaphore mode (NT) or exit (EX). Push ENTER to confirm.
cr (Aux) Courtesy light
mode
Y5
Enabled
Nt
Disabled
ex EXIT or push together
cr (AUX) COURTESY LIGHT MODE - Set if AUX dry contact works as courtesy light or as blinker. Use up/down to
choose courtesy light mode (Y5), Blinker mode (NT) or exit (EX). Push enter to confirm.
D2 Load defaults
Y5 Enabled
Nt
Disabled
ex EXIT or push together
D2 LOAD FACTORY SETTINGS - To reset the control unit to factory conditions, select this menu and then confirm
by selecting YES (Y5).
rc Release torque at the
end of closing
Y5 Enabled
Nt
Disabled
ex EXIT or push together
RC RELEASE AT END OF CLOSING - By activating this function (Y5) the motor will perform a brief inversion at the
end of closing, in order to release the mechanical tension.

Ar Remote learning of
transmitters
Y5
Enabled
Nt Disabled
ex
EXIT or push together
AR REMOTE LEARNING OF TRANSMITTERS- Enables (y5) or disables (nt) remote control learning (see chapter
Remote control self-learning).
rm Receiver mode
1b Independent insertion
4b
Automatic insertion
ex EXIT or push together
RM RADIO MODE
-1B: Each button of a new transmitter enter separately. User can choose the associated channel (C1 Start/open,
C2 Pedestrian/close, C3 courtesy light command).
-4B: Once you enter a button of transmitter in memory, All other buttons works. Each button take a channel
between (open, close, pedestrian and stop)
cn Counter
00 1 pair of digits
00
2 pair of digits
00 3 pair of digits
ex
EXIT or push together
CN COUNTER Show the counter in 3 groups of 2 numbers. Eaxmple: 123.456 is displayed as : 1.2 - 34. - 56
MM Mass mode
Y5
Enabled
Nt Disabled
ex
EXIT or push together
MM MASS MODE - In this menu you can enable the mass enter mode. This mode can be enabled just when
pause time is 00, this means when automatic closing is disabled. In this mode, if you push 5 times Open
command (example), the control unit count 5 cars passing through the detect sensor, then it closes the barrier.
br Barrier logic
Y5
Enabled
Nt Disabled
ex EXIT or push together
BR BARRIER LOGIC - Enables (y5) or disables (nt) the barrier operating logic. When the barrier logic is disabled,
the control unit uses the standard program to control a sliding gate.
EX

DEFAULT SETTINGS
DISPLAY
DESCRIPTION
DEFAULT
DATA
ol Operating logic 5T
Lc Radio code learning
Lt Working times learning
5p Pause time 10
Dm Dead man mode
tm Working times menù
T1 Working Time 1.8( 180sec.)
Tp Pedestrian opening time 08
tc Courtesy light time 12
Gd Gate direction rh
Pc Photocell input polarity No
Pt Photostop / Protection mode Pt
5p Stop input polarity No
L5 Limit switches polarity no
Pr Motor power in fast speed 10
Pl Motor power in slowing down 10
55 Soft Start Y5
Bl Blinker mode Y5
Cr (Aux) Courtesy light mode Y5
D2 Load defaults
Rc Release torque at the end of closing Nt
Ar Remote learning of transmitters Nt
Rm Receiver mode 1b
Cn Counter
Mm Mass mode nt
br Barrier logic nt

Need some help or advice with your installation?
Keep this sheet handy because you might need this email address –
[e-mail]
Internet and technology give us the ability to have a technician look at your install and help
solve problems whether they are the initial installation or years later.
1. Don’t start dismantling anything until advised.
2. Email the service department at the address above.
SEND US YOUR PHOTOS AND GIVE US SOME EYES ON SITE
•Photo of the overall scene – we should be able to see the whole gate/s in this one photo.
•A couple of photos of the gate hinges (if swing gates).
•Photos of both opening stops and closing stops.
•Photo of the connections to any battery.
•A couple of photos of the control board wiring.
•Any other shots you think important.
NB: Please resize your photos before emailing.
Please attach photos as attachments and do not imbed them in the email.