Graco LazerGuide 1700 User manual

3A5294B
EN
Instructions
LazerGuide 1700, LazerGuide 2000
and LazerGuide 3000 Kits
For installation of the LazerGuide 1700, 2000 and/or 3000 Kits on LineLazer™, RoadPak™, Sure
Stripe 3350SP, and Brite Striper 3500SP airless line striping systems.
For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual and in related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Related Manuals:
3A3388 LLV 3900/5900 Operation
3A3426 LLV 200HS Operation
3A3393 LLV 250SPS and 250DC Operation
3A4603 LL ES1000 Operation, Repair, Parts
3A4637 SureStripe 3350 Operation, Repair, Parts
3A4555 BriteStriper 3500 Operation
3A5384 RoadPak Operation
------- Laser Manufacturer’s Manual
LASER LIGHT HAZARD: AVOID DIRECT EYE
CONTACT
Eye exposure to Class IIIa/3R levels of laser light can
potentially present an eye (retinal) injury hazard,
including spot blindness or other retinal injury. Refer
to laser warnings in laser manufacturer’s manual.
LazerGuide 2000
LazerGuide 3000
LazerGuide 1700

Table of Contents
2Instructions
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . 3
LazerGuide 1700 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LineLazer V 3900, 5900 & 200HS . . . . . . . . . . . 4
LazerGuide 1700 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LineLazer 250SPS & 250DC . . . . . . . . . . . . . . . 5
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
25A530, 25A691, 17P782, 17P784 . . . . . . . . . . 7
LazerGuide 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Calibrating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the Laser . . . . . . . . . . . . . . . . . . . . . . . . . 11
Parts - 17T540, 17T541 & 17T543 . . . . . . . . . . . . . 12
Parts - 17T544 and 17T545 . . . . . . . . . . . . . . . . . . 13
Parts - 17U799 and 17U800 . . . . . . . . . . . . . . . . . . 14
Parts - 17W270 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LazerGuide 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using the Laser . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wiring Installation (Models prior to 2018) . . . . . . 18
250DC & 250SP . . . . . . . . . . . . . . . . . . . . . . . . 18
Parts - 17T542 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Parts - 17V405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Parts - 17U930 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Y Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . 22
LineLazer V Series (17T537) . . . . . . . . . . . . . . . 22
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 23
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 24

Kits
Instructions 3
Kits
Battery Disposal
Do not place batteries in the trash. Recycle batteries according to local regulations. In the USA and Canada call
1-800-822-8837 to find recycling location or go to www.call2recycle.org.
LazerGuide 1700 Kits
Kit Number Striper Pages
25A530 LineLazer V 3900, 5900 & 200HS HP Automatic
Series and 200HS HP Reflective Series
4-7
25A691 LineLazer 250DC and 250SPS
17P782 LineLazer ES1000
17P784 SureStripe 3350SP and BriteStriper 3500SP
LazerGuide 2000 Kits
Kit Number Striper Pages
17T540 LineLazer V HP Automatic Series
8-15
17T541 LineLazer V Standard Series
17T543 LineLazer ES1000
17U799 LineLazer 3400 (North America)
17T544 LineLazer IV 3900, 5900, 130HS, 200HS
17U800 LineLazer 3400 (Worldwide)
17T545 LineLazer IV 3900, 5900, 130HS, 200HS
(Worldwide)
17W270 LineLazer 250 (Worldwide)
LazerGuide 3000 Kits
Kit Number Striper Pages
17T542 LineLazer 250DC and 250SPS
16-21
17U930 RoadPak
17V405 LineLazer V 200HS

LazerGuide 1700
4Instructions
LazerGuide 1700
LineLazer V 3900, 5900 & 200HS
1. Remove battery cover.
2. Attach ON/OFF switch to desired location on the
handle bar.
3. Attach laser to desired location on the gun arm.
4. Route wires up to the battery and connect to the (+)
and (-) terminals.
5. Connect the switch leads to the laser wire harness.
6. Reattach battery cover.
7. Turn on laser and position dot underneath gun
head.
NOTICE
Do not connect GL1700 directly to a generator source
as it can create over voltage and damage to the elec-
tronics.
ti27886a
ti27815a
ti27816a
ti27818a
ti27887a
ti27888a
ti27817a

LazerGuide 1700
Instructions 5
LazerGuide 1700
LineLazer 250SPS & 250DC
1. Lower platform.
2. Remove coiled hose.
3. Remove battery.
4. Attach ON/OFF switch on right side of handlebar
and connect jumper.
5. Route switch wiring between piston and square
tube, and down to battery.
6. Route jumper between piston and square tube, and
down to gun cable hole.
7. Secure switch wiring and jumper using cable tie.
8. Attached laser to desired location on gun arm.
ti28211a
ti28212a
ti28213a
ti28214a
ti28215a
ti28525a
ti28237a
ti27816a

LazerGuide 1700
6Instructions
9. Route switch wires down to battery and connect to
the (+) and (-) terminals, and route jumper through
gun cable hole.
10. Connect the jumper to the laser wire harness, and
secure all cables as necessary.
11. Reinstall the battery.
12. Replace the coiled hose.
13. Turn on laser and position dot underneath gun
head.
NOTICE
Do not connect GL1700 directly to a generator source
as it can create over voltage and damage to the elec-
tronics.
ti28238a
ti27887a
ti28239a
ti28240a
ti27817a

Parts
Instructions 7
Parts
25A530, 25A691, 17P782, 17P784
1
2
7
5
3
4 (17H718) 6
ti28242a
9
4 (17H713, 17P947,17P494)
Ref. Part Description Qty
1 17H714 MODULE, laser, green dot 1
128914 MANUAL, operations, laser 1
128915 CARD, operator, laser 1
128916 LABEL, operations, laser light 1
2 128917 SHIELD, paint, laser, assy. 1
3 128865 BRACKET, mounting, laser, assy. 1
4 17H718 SWITCH, on/off, laser module (25A691) 1
17H713 SWITCH, on/off, laser module (25A530)
17P947 SWITCH, on/off, laser module (17P782)
17P494 SWITCH, on/off, laser module (17P784)
128857 FUSE, blade, mini, 3 amp 1
5 128854 STRAP, cable, velcro 1
6 178342 CLIP, spring 2
7 404989 STRAP, tie
(25A691, 17P782, 17P784) 4
(25A530) 2
9 17H745 CONDUCTOR, electrical, jumper
(25A691)
1
Series A uses an external in-line fuse
Series B uses an internal self-resetting fuse
Series C uses an internal self-resetting fuse and an external
in-line fuse
Ref. Part Description Qty

LazerGuide 2000
8Instructions
LazerGuide 2000
Mounting
The LazerGuide 2000 mounts to any walk behind striper
using a 5/8” round gun support bracket. For day use, the
height of the laser unit should be 24”-36” above ground
level for optimum performance. This provides better
reflectivity off of the target box. Recommended height for
night use is 12”-24” which provides a longer reference
line on the ground.
Mount in rear, above and in-line with spray nozzle. Refer
to LazerGuide 1700, page 4, steps 1-7.
Recommended Battery Location (if
applicable)
Bolt the 12V DC battery kit to the machine’s existing
plate using supplied 1/4-20 hardware.
NOTE: Some machines will require different mounting
locations.
LL3400 shown:
NOTICE
Do not operate the LazerGuide
2000 directly from a
generator source as doing so can create over voltage
to the laser and damage the electronics.

LazerGuide 2000
Instructions 9
Calibrating
The procedure may take a few attempts until properly
aligned. Calibration only has to be performed periodi-
cally. Use this procedure for front or rear mounted laser.
Also applies to auto-layout series.
1. Find an existing long straight line such as a
curb or a previously striped line. Mark halfway
point and set the target box at far end.
2. At the starting point, make sure your striper frame is
true to your reference line by pushing the machine
about 10 feet while keeping the spray nozzle over or
parallel with the line. Make sure the laser is level,
then adjust the laser left-right until it is centered in
the target box at the far end.
3. Tilt laser downward and swing spray gun left or
right until it is in line with the laser. Adjust laser
back to upward position.
4. Position spray nozzle directly over reference line
and maneuver machine left-right until laser is cen-
tered in target box at the far end. Make sure spray
nozzle is centered over line.

LazerGuide 2000
10 Instructions
5. Walk towards target box while keeping the laser
centered in the target box at the far end. Look only
at the target NOT at the spray nozzle. Stop at half-
way point and check the position of the spray nozzle
relative to the line.
6. If the spray nozzle is to the left of the reference line
by 1 1/2”, for example, adjust the laser using the
fine-line adjustment screws 1 1/2” to the left of the
center line (same distance to the same side on the
target box).
7. Go back to the starting point and center the laser in
the target box with the spray nozzle directly over the
line. Walk to the halfway point keeping the laser
centered on the target. If the laser is centered in the
target and the spray nozzle is over the reference
line, you are calibrated. If not, repeat step 6.

LazerGuide 2000
Instructions 11
Using the Laser
You need two points. A starting point to position the
spray nozzle over and an ending point to stripe to.
Day Use
For day operation, the target box is placed at the far
point of your stripe to line (use two target boxes at either
end for quicker operation). You will not see the green
line along the surface you are striping during the day,
but you will see the line on the target at the far end up to
several hundred feet away.
1. Place reflective target box at your ending point (up
to 700 feet).
2. Position spray nozzle with laser over your starting
point.
3. Slightly loosen vertical adjustment knob and rotate
LazerGuide 2000 up or down until the laser stripe
on the far target is the brightest. Lock vertical
adjustment knob.
4. Start striping while keeping laser in the center of the
target box. Keep your eyes on the target, NOT on
the spray nozzle.
Night Use
For night operation, the target box is optional since you
can see the bright green line on the surface you are
striping. However, the target is useful for longer runs as
a visual tool to determine the end of the run.
1. Turn laser on. Position spray nozzle with laser over
your starting point.
2. Use the laser as your string line to connect the start-
ing point to the ending point.
3. Optional: Use the reflective target box for long dis-
tance lines.

Parts - 17T540, 17T541 & 17T543
12 Instructions
Parts - 17T540, 17T541 & 17T543
Ref Part Description Qty
1 17T534 LASER, LazerGuide 2000 1
2 17T535 MOUNT, laser 1
3 17T536 BOX, target 1
4 287453 BRACKET, support 1
5 17U821 BRACKET, mount 1
6 111145 KNOB, pronged 1
7 17H713 SWITCH, on/off laser (17T540 &
17T541)
1
8 178342 CLIP, spring 1
9 17P947 SWITCH, on/off laser (17T543) 1
10 25A526 KIT, battery, 12 V (includes charger
board) (17T541)
1
11 128854 STRAP, cable velcro 1
12 404989 STRAP, tie 1
Ref Part Description Qty

Parts - 17T544 and 17T545
Instructions 13
Parts - 17T544 and 17T545
Ref Part Description Qty
1 17T534 LASER, LazerGuide 2000 1
2 17T535 MOUNT, laser 1
3 17T536 BOX, target 1
4 17T398 MOUNT, g-clamp 1
5 17J407 ARM, extension, gun support 1
7 128854 STRAP, cable velcro 1
9 17T408 KIT, battery, 12V 1
10 17V737 CHARGER, battery, 12V 1
11 404989 STRAP, tie 1
Ref Part Description Qty

Parts - 17U799 and 17U800
14 Instructions
Parts - 17U799 and 17U800
Ref Part Description Qty
1 17T534 LASER, LazerGuide 2000 1
2 17T535 MOUNT, laser 1
3 17T536 BOX, target 1
4 287453 BRACKET, support 1
5 111145 KNOB, pronged 1
6 17U801 BRACKET, battery 1
7 128854 STRAP, cable velcro 1
8 17T408 KIT, battery, 12V 1
9 17V737 CHARGER, battery, 12V 1
10 404989 STRAP, tie 1
Ref Part Description Qty

Parts - 17W270
Instructions 15
Parts - 17W270
Ref Part Description Qty
1 17T534 LASER, LazerGuide 2000 1
2 17T535 MOUNT, laser 1
3 17T536 BOX, target 1
4 108471 KNOB, pronged 1
5 17H528 BRACKET, gun arm 1
6 114982 SCREW, cap, flng hd 2
7 101566 NUT, lock 2
8 193658 SPACER, seal 1
9 287453 BRACKET, support, extension 1
11 131389 CONDUCTOR, electrical, jumper 1
12 15B187 CONNECTOR, wire tap 1
13 404989 STRAP, tie 4
14 128854 STRAP, cable, velcro 2
Ref Part Description Qty

LazerGuide 3000
16 Instructions
LazerGuide 3000
Mounting (250SPS & 250DC)
If prior to 2018, install a wiring harness onto the
250SPS/250DC. See Wiring Installation (Models prior
to 2018), page 18.
Install bracket and spacer as shown.
Mount the voltage protection control box as shown.
Mounting (RoadPak)
If prior to 2018, the power needs to come from the
vehicle ignition switched power, splicing into the wiring
harness provided.
Mount the LazerGuide 3000 on the vehicle at least five
feet off the ground. Most operators prefer to mount the
laser on top of the cab. The higher up the laser is
mounted, the farther ahead of the vehicle you can aim
the laser.
The laser must be mounted on a stable surface. If the
laser base is vibrating on the vehicle, the vibration is
magnified at the laser spot and can make it difficult to
see.
NOTICE
The LazerGuide 3000 is not polarity protected. Always
use the supplied voltage protection control.
Do not operate the LazerGuide
3000 directly from a
generator source as doing so can create over voltage
to the laser and damage the electronics.

LazerGuide 3000
Instructions 17
Using the Laser
1. Slide the laser out over the line or target to be
striped.
2. Turn laser ON by turning on the sprayer.
NOTE: The laser is connected to ignition switched
power to prevent the battery from draining.
3. Push the power button on the laser.
NOTE: The laser may take a few minutes to warm up.
Be patient. The power switch will stop blinking when
ready.
4. Push power button once for solid dot. Push power
button a second time for blinking dot.

Wiring Installation (Models prior to 2018)
18 Instructions
Wiring Installation (Models prior to 2018)
250DC & 250SP
1. Remove blue cover (6 screws) with 5/16 screw nut.
2. Remove circuit board cover with 5/16 nut driver.
3. Install blue wire tap to the only RED wire having a
bullet connector. This is necessary so the battery
does not drain over night. For better access, you
can remove the key switch.
4. Use existing holes and install mounting bracket as
shown. Bracket fits snug so you may have to slightly
loosen the upper bead tank brackets to slide into
place.

Parts - 17T542
Instructions 19
Parts - 17T542
Ref Part Description Qty
1 17U933 LASER, LazerGuide 3000 1
2 17V064 CONTROL, voltage protection 1
4 111145 KNOB, pronged 1
5 17H528 BRACKET, gun 1
6 17J407 ARM, extension 2
7 131389 CONDUCTOR, electrical 1
8 15B187 TAP, wire 1
9 404989 STRAP, tie 4
10 114982 BOLT 2
11 101566 NUT 2
12 193658 SPACER 1
13 128854 STRAP, cable, velcro 2
Ref Part Description Qty

Parts - 17V405
20 Instructions
Parts - 17V405
Ref Part Description Qty
1 17U933 LASER, LazerGuide 3000 1
2 17V064 CONTROL, voltage protection 1
4 111145 KNOB, pronged 1
5 287453 ARM, extension 1
6 17U821 BRACKET, mounting, laser 1
7 17H713 SWITCH, on/off laser 1
8 178342 CLIP, spring 1
9 404989 STRAP, tie 4
10 128854 SRTAP, cable, velcro 2
Ref Part Description Qty