Graco InvisiPac Parts list manual

333349E
EN
Instructions-Parts
InvisiPac™Transformer
Upgrade Kit
To operate 240V InvisiPac units with a three-phase 400V or 480V electrical supply.
For professional use only. Not approved in explosive atmospheres or hazardous locations.
127567
400V Transformer Upgrade Kit
127568
480V Transformer Upgrade Kit
Important Safety Instructions
Read all warnings and instructions in this manual
and in the InvisiPac system manual 333347.
Save all instructions.
WLD

Installation
2333349E
Installation
This transformer must be installed by a qualified electri
cian to operate 240V InvisiPac units with a three-phase
480V electrical supply.
NOTE: Installing the transformer kit changes the model
of the InvisiPac system. Refer to the InvisiPac system
manual 333347 for model information.
1. Turn main power switch OFF.
2. Remove front access panel from electrical enclo
sure.
3. Remove cables from J2 on AWB board to main
power switch (H) and main enclosure ground (G).
4. Remove the knockout hole below main power
switch (H).
5. Insert grommet (2) in knockout hole.
6. Mount main electrical enclosure onto transformer
enclosure (4) and tighten screws (1).
7. Remove fan panel (155) on transformer enclosure
(4).
8. Insert plastic cable bushing (3) through grommet in
the top of the transformer enclosure (4) into the bot
tom of the main electrical enclosure.
All electrical wiring must be done by a qualified
electrician and comply with all local codes and
regulations.
WLD
J2
2
H
G
WLD
1
4
1
155
WLD
3
4

Parts
333349E 3
9. Run wires/cabling from transformer enclosure (4)
through plastic cable bushing (3) into main electrical
enclosure.
10. Connect fan connector from transformer enclosure
into J7 on AWB.
11. Connect black wires from transformer enclosure (4)
to J2 on AWB board according to the table below:
12. Connect ground wire from the transformer
enclosure (4) into GND on J2 of AWB and main
enclosure ground (G).
13. Connect red wires from transformer enclosure (4) to
main power switch (H) according to the following
table:
14. Re-attach fan panel (155) to transformer
enclosure (4).
15. Replace front access panel on electrical enclosure.
Parts
400V Transformer Upgrade, 127567
480V Transformer Upgrade, 127568
AWB
Terminal Wire Label
W1 AWB-W1
W2 AWB-W2
W3 AWB-W3
W4 AWB-W4
Main Power
Switch Terminal Wire Label
4T2 P1
6T3 P2
NP3
WLD
J2 J7 H
G
Ref. Part Description Qty.
1 113802 SCREW, hex hd, flanged 3
2 16C252 GROMMET, air fitting 1
3 16X916 BUSHING, cable 1
4 TRANSFORMER, assembly 1
24V015 480V (Kit 127568)
24V018 400V (Kit 127567)
WLD
1
3
2
4
1

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 333349
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision E, March 2019
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of eighteen months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For more information about InvisiPac, visit www.InvisiPac.com or email [email protected].
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
For technical assistance or customer service, call toll free: 1-800-458-2133.