Graco 224667 Datasheet

308154G
EN
Instructions - Parts List
Fas-Vac Evacuation
System
For oils and heavier lubricants. For professional use only.
Not approved for use in European explosive atmosphere locations.
FOR LUBRICATION PRODUCTS
ONLY
50 psi (0.35 MPa, 3.5 bar) Maximum Working Pressure
Model 224667
Basic Pump: Includes Husky 716 pump and mounting
hardware
Model 224700, 16 Gallon System
Includes basic pump, dolly, wand storage kit, and 1/4” x
32” suction wand
Model 224701, 55 Gallon System
Includes basic pump, 55 gallon drum truck, wand storage
kit, and 1/2” x 32” suction wand.
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . .14
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Model 224701 shown
(does not include drum or
Filter-Regulator-Lubricator Kit)

Warnings
2308154G
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and
warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-
ponent. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources, such as cigarettes and portable electric lamps.
• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
• Ground all equipment in the work area.
• Use only grounded hoses.
•Stop operation immediately if static sparking occurs or you feel a shock.Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.

Warnings
308154G 3
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin and
can cause serious injury.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Do not point the dispensing valve at anyone or at any part of the body.
• Do not put your hands or fingers over the grease fitting coupler.
• Tighten all fluid connections before operating the equipment.
• Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
• Know the specific hazards of the fluids you are using.
• Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
• Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
WARNING

Installation
4308154G
Installation
Grounding
1. Pump: Connect a ground wire (A) to the pump. Con-
nect to the other end to a true earth ground. Order
Grounding Kit (Part No. 222084). (FIG. 1)
2. Air Compressor: Follow the manufacturer’s recom-
mendations.
3. Use only metal or conductive containers.
4. All solvent pails used when flushing, according to
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non-conductive sur-
face, such as paper or cardboard, which interrupts
the grounding continuity.
FIG. 1
A

Installation
308154G 5
Typical Installation
1. Install the wheels on the dolly, or assemble the truck
according to the instructions supplied with it.
2. Put the drum on the dolly or truck. The truck has a
chain and clip (A) to secure the drum.
3. Position the pump between the bung hole and vent
hole of the drum. (FIG. 2 and FIG. 3)
4. Loosen the top screw (14) of each pump clamp (18)
and reposition the clamps as needed to fit the rim of
the drum.
5. Tighten the screws (17) to secure the pump to the
rim of the drum.
6. Install the wand storage tube (supplied). Place the
holder (206) on the lip of the dolly or truck.
7. Place the tube (202) in the holder and slide the
bracket (203) over the tube.
8. Align the bracket (203) to the holder (206) and
secure the bracket to the rim of the drum.
9. Remove the drum’s vent hole cover and install the
vented fluid gauge (23).
10. Remove the drum’s bung hole cover and install the
plug (24).
11. Put the 50” drain hose (1) into the drum through the
bung hole.
12. Connect a wand (104) to the quick coupler (7). Store
the wand in the storage tube (202) until needed.
FIG. 2: 55 Gallon Unit
A
103
206
202
18
101
7
104
23
202
203
204/205
1
24

Installation
6308154G
Air Regulation
If you are using the optional air line Filter-Regula-
tor-Lubricator (Kit 110149), see page 6 for installation
instruction.
If you are providing your own regulation, you should
install a quick disconnect coupler at the air hose and
pump inlet or regulator.
Optional Fluid Filter for Evacuation Mode
When evacuating particle-contaminated lubricants from
the 16 or 55 gallon drum to another container use a suc-
tion hose with filter (kit 223888) to prevent damage to
the pump.
FIG. 3
16 gallon drum not included
101
105
206
202
24
204/205
1
203
202
23
7
104

Installation
308154G 7
Adding an Optional Air Line
Filer-Regulator-Lubricator (FRL) Kit
Proper conditioning of compressed air help prolong the
life of your pump. In the FRL Kit, the filter removes
harmful dirt and moisture from the compressed air, the
regulator controls air to the pump and the lubricator pro-
vides automatic motor lubrication.
Graco FRL (Part No. 110149) should be mounted to the
Fas-Vac with the Mounting Kit (Part No. 224759).
1. Remove the two manifold screws, flat washers, and
lockwashers (A) from the pump.
2. Install the accessory bracket (B) so that its large
hole faces up.
3. Install the screws and lockwashers (do not use the
flat washers).
4. Remove the male quick disconnect fitting (20) from
the pump and install it in the air filter inlet (J).
5. Hold the FRL with the air filter (H) to the left. Install
the gauge (C) in the back port of the regulator (not
the top) and turn it so the gauge faces up.
6. Install the plug (G) in the front port of the gauge.
7. Remove the lock ring (F) from the base of the air
regulator knob.
8. Angle the FRL into the bracket so the gauge slides
into the slot in the bracket.
9. Screw the lock ring (F) over the regulator knob to
secure the assembly to the bracket.
10. Install a 90° nylon connector (E) to the FRL outlet
on the side of the lubricator.
11. Install the other connector to the pump air restricter
inlet (not visible in FIG. 4).
12. Tighten the connectors in a position that allows easy
installation of the nylon tube (D). Install tube.
FIG. 4
20
A
BCD
E
F
G
J
H

Operation
8308154G
Operation
Control Knob
The Fas-Vac system operates in two modes: evacuate
lubricants from the crankcase or reservoir and collect
the material in a 16 gallon or 55 gallon drum, and drain
the stored lubricants from the drum to a larger container.
The modes are selected with a lock-in-place control
knob (A). See FIG. 5.
When the system is not in use, lock the knob in the
evacuation mode.
Suction Wands
Experiment to determine which wand is best for your
application. Typically, use the largest wand possible. A
quick-disconnect coupler make it fast and easy to switch
wands.
Fluid Gauge
The fluid gauge (23) indicates approximately how full the
drum is to avoid over-filling it (FIG. 5). When it’s red cap
is even with the top, the drum will be 75% to 80% full.
Evacuation
1. Check the gauge level.
2. Be sure that the control knob (A) is in the EVACUA-
TION position and the safety clip (8) locks it in place.
3. Connect the air supply hose to the pump air inlet
(B). Operate the pump at 40-50 psi (2.72- 3.4 bar,
0.27-0.34 MPa) for the best results.
4. Insert the suction wand (104) in the crankcase or
reservoir.
5. Disconnect the air to the pump when the evacuation
in complete.
Draining the Drum
1. Remove the suction wand (104).
2. Attach the suction hose quick-disconnect coupler to
the male coupler fitting of a waste oil tank, or dis-
charge the material to an access opening.
3. Pull out the safety clip (8) and turn the control knob
(A) to drain drum.
4. Connect the air supply hose to the pump.
5. When the draining is complete, disconnect the air to
the pump, turn the valve knob (A) back to the evacu-
ation position and install the safety clip (8).
FIG. 5
104
23
8
A
B
(when using FRL kit)

Parts
308154G 9
Parts
Model 224701
55 Gallon System
Includes items 101 to 104
Part No./Description
Part of 102
7
104
1
24
103
Part of 102
101
Ref. Part Description Qty.
101 224667 PUMP 1
102 224666 WAND STORAGE KIT 1
103 111470 55 GALLON DRUM TRUCK 1
104 224702 WAND, 32” x 1/2” OD

Parts
10 308154G
Model 224700
16 Gallon Fas-Vac System
Includes items 101 to 105
Model 224665
16 Gallon Deluxe Dolly
Includes items 103a to 103f
Part No./Description
NOTE: 16 gallon drum not included.
103b
103a
103c
103d
103e or 103f
Part of
102
24
1
Part of
102
23
104
4
101
Ref. Part Description Qty.
101 224667 PUMP ASSEMBLY 1
102 224666 WAND STORAGE KIT 1
103 224665 DOLLY, 16 gallon deluxe 1
103a 205419 CLAMP, dolly, 120 lb. 1
103b 111472 CASTER, 3” 4
103c 100307 NUT, full, hex, 3/8-16 unc 2b 1
103d 100023 WASHER, flat, 3/8” 1
103e 102971 BOLT, carriage, 3/8-16 unc - 2a x 3” 1
103f 101185 BOLT, carriage, 3/8-16 unc - 2a x 4” 1
104 224669 WAND, 32” x 1/4” OD 1
Ref. Part Description Qty.