GRAFTON 397/7697 User manual

Grafton - 3 Drawers Chest
397/7697
408/6295
Assembly Instructions
- Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important – Please read these instructions fully before starting assembly
Dimensions
Width - 83cm
Depth - 43cm
Height - 86cm
Issue 1 - 05/05/15

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
. Check you have all the
components and tools listed on
pages 2 and 3.
. Remove all fittings from the
plastic bags and separate them
into their groups.
. Keep children and animals
away from the work area, small
parts could choke if swallowed.
. Make sure you have enough
space to layout the parts before
starting.
. Do not stand or put weight on
the product, this could cause
damage.
. Assemble the item as close
to its final position (in the same
room) as possible.
. Assemble on a soft level
surface to avoid damaging the
unit or your floor.
. We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
. Parts of the assembly will be
easier with 2 people.
. Dispose of all packaging
carefully and responsibly.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Care and maintenance
.
. Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
. From time to time check
that there are no loose
screws on this unit.
. This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1
56
7
8
9
10
12
13
14
15
16
11
3
24
Right back foot
Right side panel Left side panel
Top panel
Drawer bottom x3
Back panel x 2
Drawer front x 3
Back rail
Bottom front rail
Drawer back x 3
Drawer left side x 3
Drawer right side x 3
Front rail x 3
Left back foot
Left front foot Right front foot
(84.2 x 4.5cm)
(77.2 x 32.5cm) (77.2 x 32.5cm)
(83 x 43cm)
(68.9 x 35cm)
(78.2 x 37.2cm)
(72.4 x 21.3cm)
(73 x 6cm)
(73 x 6cm)
(67.5 x 15cm)
(35 x 15cm)
(35 x 15cm)
(73 x 6.5cm)
(84.2 x 4.5cm)
(84.2 x 4.5cm) (84.2 x 4.5cm)

3
2m
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
F
G H I
JL M
N
Metal dowel x 38
Washer x 01
Wall strap x 01
Locking
nut x 38 30mm Screw x 12
16mm Screw x 1 14mm Screw x 30 Nail x 25
22mm Bolt x 06 Wooden dowel x 26
Handle x 06
Right runner x 03 pair Left runner x 03 pair
O
H profile 712mm x 01

Assembly InstructionsAssembly Instructions
Step 1
Assembly Instructions
4
A
A
Attention:
Attention:
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
A
A
A
A
A
H
H
H
H
H
H
H
H
H
3
4
1
2
Fitting Metal dowels.
Screw metal dowels
in the parts indicated.
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
A
Insert dowels into the
indicated parts.
H
A
A
A
A10
3x
A
A
A
A
7

H
H
H
H
H
H
H
H
H
H
H
H
11
15
06
05
16
13
12
11 3x
3x
3x
Assembly Instructions
Step 2
5
Insert dowels into the
indicated parts.
H

Assembly Instructions
Step 3
Step 4
6
b) Insert locking nuts
where shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
.a) Fit side panel , left
front leg and left back
leg together as shown.
B
B
B
B
B
B
E
E
E
E
E
E
E
H
.a)
.b)
3
6
6
6
62
2
Correct position of the screws.
E
E
M
E
M
M
M
M
Attention pre drilled holes
Do not over tighten.
Attach left runners
to the pre drilled holes on
the left side panel
using screws .
M
B
6
03
02
6
E
Fixing runners.
6
B

Assembly Instructions
Step 5
Step 6
7
b) Insert locking nuts
where shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
05
01
04
.a) Fit side panel , right
front leg and right back
leg together.
L
B
B
B
B
B
L
L
L
L
L
B
B
1
5
5
5
5
4
4
5
E
E
E
E
EE
E
E
EE
.a)
.b)
Correct position of the screws.
Attention pre drilled holes
Do not over tighten.
Attach left runners
to the pre drilled holes on
left side panel
using screws .
L
B
5
E
Fixing runners.
L

Assembly Instructions
Step 7
Step 8
8
unfinished side
11
11
11
12
13
6
B
B
B
B
B
B
B
Assembling the cabinet.
Fit parts , ,
on the left side panel
Do not over tighten.
Insert 5 locking nuts
in the indicated parts.
Use a screwdriver to turn
locking nuts clockwise
to lock.
as shown.
12 11 13
6
B
B

Assembly Instructions
Step 9
Step 10
9
B
B
B
B
B
B
B
5
Fixing right side panel.
Fit right side panel
on to cabinet.
Insert 5 locking nuts
into rails where shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
5
B
B

B
B
B
B
7
Step 12Step 12
Assembly Instructions
Step 11
Step 12
10
B
B
Fixing the top panel.
Fit top panel on to
cabinet.
Insert 4 locking nuts
into top panel where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
B
B
7
a:
b:
c:
F
F
09
09
O
F
F
F
b:
O
09 09
100mm
09 09
F F F F F F
Fixing back panel.
Important:
Cabinet beMUST
‘square’when back panels
are attached.
Carefully slot the
second back panel into
profile and fix it to the
cabinet using nails .
c:
Attach the back panel
to the left side first
using nails .
a:
Position H profile
onto back panel (just
b:
attach).
09
F
O
09
F
H
H
X
Attention toNote:
the measures.

N
NG
G
14
CC
C
C
3x
3x
3x
.c)
.c)
8
B
B
B
B
3x
.b)
15
16
10
3x
aa)
Assembly Instructions
Step 13
11
E
E
E
E
E
L
M
S
R
BB
Step 14
Fixing runners.
Attach right runners
and left runners in the
bottom edge of the
drawers using screws
as shown.
Make sure
runners are
correctly positioned
according to the diagram
E
L
M
Assembling the drawers:
a:
back in place, press
the drawer sides and fix
c: Position large drawer
Using bolts attach
handles to the drawer
front.
G
N
Insert 4 locking nuts
into drawer sides where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
B
B
b: Slide large drawer
bottom into slots on
drawer sides.
Fit drawer sides
and to the large drawer
front .
C
16
15
10
08
14
using screws .
EE
Correct position of the screws

Assembly Instructions
Step 15
Step 16
Step 17
12
Assemble is complete
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
10
10
10
Hook the wheels of the
runners on the back of the
drawers over the wheels
of the runners on the left
and right sides, then hold
the drawers level and
slide backwards into
position.
LM
E
LM10
10
10
To move drawers up or
down:
Loosen the screws in the
runners in the side panels,
adjust the drawers to suit
and once drawers are
aligned retighten screws.
Then, add 1 screw in
the hole in each runner of
the side panels and middle
panel as indicated.
E
Adjusting drawers.
wall
I
J
D
Fixing to wall.
Furniture must be fixed to
a wall. Fix wall strap to
top of furniture using
washer and screw .
With help, move furniture
into position.
I
JD

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to - Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.