Grandstream Networks HT814 User manual

Grandstream HT814/HT818
ATA Device Installation Guide
The Grandstream HT814 is a four-port FXS and HT818 is an eight-port FXS Analog Telephone Adapter (ATA) device
packaged in a compact chassis. These devices can be used for the following purposes:
●Fax machine on FXS port
●Local or remote phone on FXS port
Overview of the Installation Process
The HT814 and HT818 are normally pre-configured for use with our StarCloud+ telephone system. In most cases,
the installer can connect the HT814 or HT818 to the customer’s network along with the appropriate analog
telephone connections.
If the provided configuration needs to be changed, it is possible to field-program the HT814 or HT818 using the
instructions covered later in this guide.
Connecting the HT814 and HT818
The rear panel of the HT814 has a power connection, four RJ11 telephone connectors, and two RJ45 network
connectors, as shown in the following picture:
HT814 Rear View
August 2019
Copyright © 2019, Star2Star Communications®, LLC. All rights reserved. Star2Star is a registered trademark of Star2Star
Communications, LLC. All logos and company names are trademarks or service marks of their respective companies.

Grandstream HT814 and HT818 ATA Device Installation Guide
The rear panel of the HT818 has a power connection, eight RJ11 telephone connectors, and two RJ45 network
connectors, as shown in the following picture:
HT818 Rear View
The connectors are used as follows:
Connector
Purpose
DC 12V
Power connector. Connect the provided AC power supply here.
Note: Does not operate on Power over Ethernet (PoE).
Connection for a laptop computer. Use this connection for field re-configuration.
Connection to the local network (if used as a local device) or to a WAN connection (if
used as a remote device).
Connections for an FXS (station) device, such as an analog telephone or a fax machine.
The LAN port is only used to access the HT814 or HT818’s built-in configuration server from a connected laptop.
This is necessary to perform the initial configuration. After the device is configured, the LAN cable can be
disconnected.
Pre-Installation Configuration
Ensure that the HT814 or HT818 device is added to the customer system and correctly provisioned using the
portal. ATA devices are added via the Multi-Extension Devices page in the portal. Analog phone and fax Extensions
are configured via the Extensions page in the portal. For more information, refer to the ATAs Portal Configuration
Guide.
The HT814 and HT818 can be configured for either local (On-Net) or remote (off-net) use. If you are re-deploying
an HT814 or HT818 that was already configured, follow the instructions in the Factory Reset  section below. Then,
configure the device for either local or remote operation. A device configured for local operation does not work as
a remote device and vice-versa, so it is important to apply the correct configuration to the HT814 or HT818.
Page 2

Grandstream HT814 and HT818 ATA Device Installation Guide
If you are unsure about the current configuration, perform the factory reset and then configure the device.
Factory Reset
To factory reset the HT814 or HT818 ATA device:
1. Unplug the cable from the WAN or LAN port.
2. Locate the small hole on the back panel of the unit next to the power connector, to the left for HT814 and
to the right for HT818.
3. Insert a straightened paper clip or other thin tool into the hole, and press for about seven seconds. Once
removed, the device resets to the factory settings.
Configure as a Local Device
To configure the HT814 or HT818 ATA device as a local device:
1. Connect an ethernet cable from a laptop computer to the LAN port on the HT814 or HT818 device.
Important: The computer must be configured to obtain an IP address automatically using DHCP.
2. Connect an ethernet cable to the local network using the WAN port.
3. Access a Web browser and direct the browser to http://192.168.2.1. The HT814 or HT818 login screen
displays.
4. For the user name and password, enter admin (all lower case) in both fields. The main configuration menu
displays.
5. Use the HT814 or HT818 configuration menu to configure the WAN port to use VLAN 41.
6. Select Advanced Settings. Scroll down to Firmware Upgrade & Provisioning: Upgrade VIA, select HTTP.
7. For the configuration server address, enter 10.41.22.99.
8. Once connected to switch on VLAN 41, the HT814 or HT818 obtains the necessary configuration data. This
will allow device registration. The HT814 or HT818 is now ready to use.
Once registered, the HT814 or HT818 can make and receive inbound and outbound calls.
Configure as a Remote Device
The HT814 and HT818 can operate as a remote device, but it requires installation-specific configuration
information to operate. For assistance, contact Star2Star Technical Support.
Page 3

Grandstream HT814 and HT818 ATA Device Installation Guide
HT814 and HT818 Status Lights
The following status lights are available on the HT814 and HT818 top panel:
Light
Blue Light Indicates
Connected to power.
Phone is connected and off-hook.
Connected to a WAN connection.
Connected to a LAN connection.
HT814 Top View
 HT818 Top View
Page 4