GRASS VALLEY 8906 User manual

J1 J2
J3 J4
J5 J6
J7 J8
J9 J10
Outputs Outputs
Loopthru
Input
8900V-R
Analog
Video
Outputs
Analog
Video
Input
EQ
Adjust
Video Input
Presence Detection
AC Coupled
DC Coupled
DC Restored
Clamped
White
Clip
Gain
Specifications Ordering Information
26
Key Features
Suitable for NTSC, PAL, SECAM, RGB, YUV,•
Tri-level sync
Passive differential looping input with•
eight active outputs
NTSC/PAL input presence detection with•
SNMP trap generation
Selectable AC, DC, DC restore, or clamp•
(slow/fast) input coupling
Selectable, dual-speed clamp for single-•
ended hum rejection
Adjustable White Clipper removes peak•
impulse transients
Card-edge adjustable cable-specific•
equalization for up to 300 meters
Card-edge adjustable gain control•
Excellent differential gain and phase•
specifications
Card-edge status indicators•
This distribution amplifier offers all the features
and functionality of our 8901 utility DA and our
8902 equalizing DA, plus a dual-speed clamp
and video presence detection with SNMP trap
generation. While all Grass Valley distribution
amplifiers remove differential or common mode
hum induced by cable runs adjacent to AC
mains cables, this module offers a dual-speed
self-clamping circuit to handle single-ended
hum caused by grounded coaxial cable shields.
Additionally, a White Clipper circuit eliminates
impulse noise above a user-selectable
threshold. And the user-enabled video
presence detection feature generates SNMP
traps that can be sent to our NetCentral SNMP
manager or other SNMP systems for mission-
critical applications.
8906-EQ-11
Belden RG11/U, 8238
cable
8906-EQ-1694
Belden 1694A cable
8906-EQ-8281
Belden 8281 cable
8906-EQ-0.03-0.14
Belden 1505A and Gepco
VPM 2000
8906-EQ-9259
Belden RG59U, 9259
cable
8906-EQ-VDM230
Gepco VDM230 cable
8906-EQ-1.0-6.6
PIK AF 0.6/6.6 cable
8906-EQ-0.6-2.8
PIK AF 0.6/2.8 cable
8906-EQ-0.6-3.7
PIK AF 0.6/3.7 cable
8906-EQ-PSF1-3
PSF 1/3 cable
8906-EQ-5C2VS
Canare L-5C2VS cable
8906-EQ-VCB100
S2CEB VCB100 cable
Supported Frame Types
GeckoFlex with 8900V-R GeckoFlex Video rear module,
Gecko video frames: 8900TX-V, 8900TF-V, 8900TFN-V
Power Rating
2.3 Watts – single slot
Input
Type: 1 Vp-p analog video with operation up to 2 Vp-p
NTSC, PAL, SECAM, RGB, YUV, Tri-level sync
Connector type: BNC
Impedance: Passive high impedance differential
loop-through
Return loss: >40 dB up to 5 MHz
CMRR: >66 dB 50/60 Hz
Common mode input: ±10V
Output
Voltage: 1 Vp-p ±2 dB
Number of outputs: Eight active plus one passive
loop-through input
Connector type: BNC
Impedance: 75Ω
Return loss: >40 dB up to 5 MHz
Output DC: <50 mV
Performance
Cable equalization: Dual range
•0to150m(0–500ft.)
•150to300m(500–1000ft.)
White clip: On/off user selectable
Frequency response:
•±0.05dBto5MHz
•±0.1dB5to8MHz
•–1dBat16MHz
Differential gain: <0.1%
Differential phase: <0.1°
Gain range: ±2 dB
Tilt: <0.5%
Coupling: AC, DC, DC restore, clamp two speeds
Clamp hum rejection:
Slow: 20 dB
Fast: 46 dB
Electrical length: 22 ns
Temperature range: 0° to 30°C
Indicators/Controls
User controls: Output gain adjustment range: ±2 dB
EQ adjustment for up to 300 meters of input cable
White clipper adjustment range: 500 mV to 1200 mV
LED indicators: Fault, power, frame bus
communication
8906 Analog Video Clamping Equalizing Distribution Amplifier w/SNMP
This module can be mounted in a GeckoFlex
frame when ordered with the 8900V-R GeckoFlex
Video rear module.
For detailed specifications, installation, and setup
instructions see:
www.grassvalley.com/docs/modular