GRASS VALLEY 2041EDA User manual

2041EDA
WIDEBAND REAR EQUALIZING DA
Instruction Manual
071803201
FIRST PRINTING: JANUARY 2001
REVISED PRINTING: JANUARY 2003
1.0software release

22041EDA Instruction Manual
Contacting Grass Valley Group
Copyright © Grass Valley Group. All rights reserved.
This document may not be copied, in whole or in part, or otherwise reproduced, except as specifically
permitted under U.S. copyright law, without the prior written consent of Grass Valley Group, P.O. Box
599000, Nevada City, CA 95959-7900 USA. GRASS VALLEY GROUP is a registered trademark and
Grass Valley is a trademark of Grass Valley Group. All registered trademarks and trademarks are prop-
erty of their respective holders. Grass Valley Group products are covered by U.S. and foreign patents,
issued and pending. Product options and specifications subject to change without notice. The informa-
tion in this manual is furnished for informational use only, is subject to change without notice, and
should not be construed as a commitment by Grass Valley Group. Grass Valley Group assumes no re-
sponsibility or liability for any errors or inaccuracies that may appear in this publication.
Grass Valley Group Web Site
The www.thomsongrassvalley.com web site offers the following:
Online User Documentation
— Current versions of product catalogs, brochures,
data sheets, ordering guides, planning guides, manuals, and release notes
in .pdf format can be downloaded.
FAQ Database
— Solutions to problems and troubleshooting efforts can be
found by searching our Frequently Asked Questions (FAQ) database.
Software Downloads
— Software updates, drivers, and patches can be down-
loaded.
Region Voice Fax Address Web Site
North America [phone]
Support: 530-478-4148 Sales: [phone] Support: [phone] Grass Valley Group P.O. Box 599000
Nevada City, CA 95959-
7900 USA
www.thomsongrassvalley.com
Pacific Operations [phone]
Support: 852-2585-6579 [phone]
U.K., Europe, Asia, Middle East [phone] [phone]
France [phone]
Germany [phone] [phone]

2041EDA Instruction Manual 3
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2041EDA Wideband Rear Equalizing Distribution Amplifier
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Module Placement in the 2000 Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation Indicator LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Configuration and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Module Configuration Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Software Update Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power-up Diagnostics Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Module Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Input Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Output Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

42041EDA Instruction Manual
Contents

2041EDA Instruction Manual 5
Preface
About This Manual
This manual describes the features of a specific 2000 Series module in the
Kameleon Media Processing System. As part of this module family, it is
subject to Safety and Regulatory Compliance described in the 2000 Series
frame and power supply documentation (see the 2000 Series Frames
Instruction Manual).

62041EDA Instruction Manual
Preface

2041EDA Instruction Manual 7
2041EDA Wideband Rear
Equalizing Distribution
AmpliÞer
Introduction
The 2041EDA Wideband Rear Equalizing DA provides basic equalization
and distribution of a single standard or high definition wideband signal
(4 Mb/s to 1.5 Gb/s) to eight outputs. The single module resides in any
rear slot of a Kameleon 2000 Series frame and is independent of any front
card for operation.
The features of the 2041EDA include:
•Auto equalization of both SD and HD signals,
•Accepts a wide range of standard or high definition input signal stan-
dards,
•Use of non-inverted outputs allow distribution of compressed signals
such as SMPTE 310M and DVB-ASI,
• Ideal for monitoring or distributing reclocked signals from adjacent
2000 modules, and
•Remote control and monitoring support.

82041EDA Instruction Manual
Installation
Installation
Installation of the 2041EDA module is a process of:
• Placing the module in a rear frame slot, and
•Cabling signal ports.
The 2041EDA module can be plugged in and removed from a Kameleon
2000 Series frame with power on. When power is applied to the module,
LED indicators reflect the initialization process (see Power Up on page 10).
Module Placement in the 2000 Frame
There are twelve rear cell locations in the 3 RU frame to accommodate
either analog or digital modules. The 2041EDA rear module plugs into any
one of the rear slots of the Kameleon 2000 frame.
1.
Install the module by inserting it into any rear slot of the frame as
illustrated in Figure 1.
2.
Verify that the module connector seats properly against the midplane.
3. Secure the module to the rear of the frame with the two screw locks on
either side of the back panel using a crossblade screwdriver.
Figure 1. Installing 2041EDA Module
J10 SIG
IN
J9 J8 J7 J6 J5 J4 J3 J2
2041
EDA
J1
Alignment post
and receptacle
Screw lock
(both sides)
8032_01
2000 frame (rear view) Board edge guides
(both sides)

2041EDA Instruction Manual 9
Installation
Cabling
Cabling to the 2041EDA module is done on the BNCs on the rear of the
module. Refer to Figure 2 for a detailed illustration of the rear connections
referenced below.
Inputs
The 2041EDA will accept any of the video standards listed in the Input
specifications in Table 3 on page 14. Connect a video input to BNC J10.
Outputs
The 2041EDA outputs conform to the video standards listed in the Output
specifications in Table 3 on page 14.
Connect video destinations to any of the eight outputs at connectors J2 – J9.
Terminate any unused outputs.
Note BNC J1 is not used on this module. On earlier versions of the 2041EDA
labeled with part number 671-5248-00, BNC J1 provided an output.
Figure 2. 2041EDA Input/Output Connectors
8032_02r1
J10 SIG J9 J8 J7 J6 J5 J4 J3 J2 J1
In 2041EDA
Outputs
Signal Present
LED
Video
Input Not
Used

10 2041EDA Instruction Manual
Power Up
Power Up
The on-board LED indicators are illustrated in Figure 3. Upon power-up,
the green PWR LED should light and the yellow CONF LED should illumi-
nate for the duration of module initialization.
Operation Indicator LEDs
With a valid input signal connected, the green on-board PWR LED,
SIG_PRES LED and the SIG LED (visible from the rear) should be on. Refer
to Table 1 on page 11 to see a complete list of possible operating conditions
and the resulting indicator status.
Figure 3. LEDs and Configuration Switches
8032_03
F1
FAULT Fault – (red) off during normal operation
Communication – (yellow)
Configuration – (yellow)
Power – (green) on during normal operation
Remote override – (yellow)
Signal present – (green)
COMM
CONF
PWR
SIG_PRES
Signal present – (green) on rear connector plate