GRASS VALLEY 8943RDA-D User manual

Specifications Ordering Information
Ordering Information
Ordering InformationSpecifications
8943RDA-D Dual SD/HD/3G Reclocking Distribution Amplifier
Key Features
Supports SD/HD/3G-SDI rates up to 1080p•
Two electrical inputs•
Four electrical reclocked output pairs•
Configurable input to output pair mapping•
Auto or manual input format selection•
100% DVB ASI compliant•
High density (up to twenty DA inputs per•
2 rack unit)
Remote control and monitoring via•
Ethernet frame interface
Applications
Distributing HD/3G signals or mixed HD/3G•
and SD format installations
Installations where an SD to HD/3G update•
is planned
Installations where highest density is•
required at the lowest cost
For optimizing and adapting trade-off•
between number of DAs and number of
outputs
J9
Input
J10
Input
Equalizer
Reclock Bypass
Reclocker
Equalizer
Reclock Bypass
Reclocker
Input to
Output
Mapping
J1
J2
J3
J4
J5
J6
J7
J8
Supported Frame Types
GeckoFlex frame
Power Rating
3.8 Watts – single slot
Inputs
SD/HD-SDI: Two electrial inputs (J9 and J10)
•Inputequalization(Belden1694Acable)
90m for 3 Gb/s (Input 1, J9)
100m for 3 Gb/s (Input 2, J10)
140m for 1.5 Gb/s
400m for 270 Mb/s
•Returnloss:>15dBupto1.5Gb/s,
10 dB (typical) up to 3 Gb/s
Formats supported:
•SD-SDI
•HD-SDI
•3G-SDI
•DVBASI
Outputs
SD/HD-SDI: Eight reclocked electrical outputs (in four
output pairs: J1/J2, J3/J4, J5/J6 and J7/J8)
•Returnloss:>15dBupto1.5Gb/s,
>10 dB to 3 Gb/s
•Signallevel:800mV±10%
•Outputjitter(forinputsconformingtoSMPTE259M
and 292M standards):
<0.2 UI >100 kHz for 3G
<0.2 UI >100 kHz for HD
<1.0 UI 10 Hz – 100 kHz for HD
<0.2 UI 10 Hz – up for SD
DVB ASI: Eight non-inverted outputs (four output pairs)
Distribution
Reclocking: Active/bypass
Input format selection: Auto/manual
Input to output mapping: Both inputs are active at
the same time and are configurable to any output pair
(one input per electrical output pair).
Electrical length (input to output latency in ns):
CH1: Input J9 to Output J1:
3G: Reclocked: 3.8 ns, Bypassed: 3.55 ns
HD: Reclocked: 4.0 ns, Bypassed: 3.6 ns
SD: Reclocked: 6.0 ns, Bypassed: 4.0 ns
CH2: Input J10 to Output J1:
3G: Reclocked: 4.0 ns, Bypassed: 3.75 ns
HD: Reclocked: 4.1 ns, Bypassed: 3.7 ns
SD: Reclocked: 6.2 ns, Bypassed: 4.25 ns
Control and Monitoring
SNMP: Yes
Web page configuration: Yes
Local configuration: Yes
Newton support: Yes
NetConfig support: Yes
NetCentral support: Yes
This module can be mounted in a GeckoFlex
frame but not in other 8900 series frames
including Gecko-A or Gecko-V frames.
8943RDA-D
Dual SD/HD/3G-SDI reclocking distribution amplifier,
front and rear module set
The 8943RDA-D is a dual input SD/HD/3G-SDI
reclocking distribution amplifier. It provides two
electrical inputs that can be mapped to feed
any of four reclocked electrical output pairs
(one input per output pair). The module is also
completely DVB ASI compliant.
It can distribute either HD/3G-SDI or SD-SDI,
making it ideal for mixed format applications or
installations where an upgrade to HD/3G-SDI
is planned. Up to 90 meters for input 1 (J9),
100 meters for input 2 (J10) of Belden 1694A
cable can be equalized for HD/3G-SDI and up
to 440 meters for SD-SDI.
All parameters can be configured directly
from the card edge or via a standard HTML
Web browser when the 8900NET (Net Card)
Network Interface module has been installed.
The module operation and configuration, as
well as the signal presence and format, can
be monitored using industry standard SNMP
protocol via the 8900NET (Net Card) module.
J1 J2
J3 J4
J5 J6
J7 J8
J9 J10
Out
Out
Out
Out
Out
Out
Out
Out
In
In
89003E-R
For detailed specifications, installation, and setup
instructions see:
www.grassvalley.com/docs/modular
34