GRASS VALLEY K2 DYNO - User manual

K2 Dyno
Replay System
Quick Start Guide
Software Version 1.5
071-8681-01
January 2010

Affiliate with the N.V. KEMA in The Netherlands
CERTIFICATE
Certificate Number: 510040.001
The Quality System of:
Thomson Inc, and its worLdwide Grass Valley division affiliates DBA
GRASS VALLEY
Headquarters
400 Providence Mine Rd
Nevada City, CA 95959
United States
15655 SW Greystone Ct.
Beaverton, OR 97006
United States
10 Presidential Way
Suite 300
Woburn, MA 01801
United States
Kapittelweg 10
4827 HG Breda
The Nederlands
7140 Baymeadows Way
Ste 101
Jacksonville, FL 32256
United States
2300 So. Decker Lake Blvd.
Salt Lake City, UT 84119
United States
Rue du Clos Courtel
CS 31719
35517 Cesson-Sevigné Cedex
France
1 rue de l’Hautil
Z.I. des Boutries BP 150
78702 Conflans-Sainte
Honorine Cedex
France
Technopole Brest-Iroise
Site de la Pointe du Diable
CS 73808
29238 Brest Cedex 3
France
40 Rue de Bray
2 Rue des Landelles
35510 Cesson Sevigné
France
Spinnereistrasse 5
CH-5300 Turgi
Switzerland
Brunnenweg 9
D-64331 Weiterstadt
Germany
Carl-Benz-Strasse 6-8
67105 Schifferstadt
Germany
Including its implementation, meets the requirements of the standard:
ISO 9001:2008
Scope:
The design, manufacture and support of video and audio hardware and software products and
related systems.
This Certificate is valid until: June 14, 2012
This Certificate is valid as of: June 14, 2009
Certified for the first time: June 14, 2000
H. Pierre Sallé
President
KEMA-Registered Quality
The method of operation for quality certification is defined in the KEMA General Terms
And Conditions For Quality And Environmental Management Systems Certifications.
Integral publication of this certificate is allowed.
KEMA-Registered Quality, Inc.
4377 County Line Road
Chalfont, PA 18914
Ph: [phone]
Fax: [phone]
CRT 001 073004
Accredited By:
ANAB

K2 Dyno
Replay System
Quick Start Guide
Software Version 1.5
071-8681-01
January 2010

4K2 Dyno Replay System Quick Start Guide 28 January 2010
Copyright Copyright © Grass Valley, Inc. All rights reserved. Printed in the United States of America.
Portions of software © 2000 – 2010, Microsoft Corporation. All rights reserved. This document
may not be copied in whole or in part, or otherwise reproduced except as specifically permitted
under U.S. copyright law, without the prior written consent of Grass Valley, Inc., P.O. Box
59900, Nevada City, California 95959-7900. This product may be covered by one or more U.S.
and foreign patents.
Disclaimer Product options and specifications subject to change without notice. The information in this
manual is furnished for informational use only, is subject to change without notice, and should
not be construed as a commitment by Grass Valley, Inc. Grass Valley, Inc. assumes no
responsibility or liability for any errors or inaccuracies that may appear in this publication.
U.S. Government
Restricted Rights
Legend
Use, duplication, or disclosure by the United States Government is subject to restrictions as set
forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause
at DFARS 252.277-7013 or in subparagraph c(1) and (2) of the Commercial Computer
Software Restricted Rights clause at FAR 52.227-19, as applicable. Manufacturer is Grass
Valley, Inc., P.O. Box 59900, Nevada City, California 95959-7900 U.S.A.
Trademarks and
Logos Grass Valley, K2, Aurora, Summit, Dyno, Solo, Infinity, Turbo, Profile, Profile XP, NetCentral,
NewsBrowse, NewsEdit, NewsQ, NewsShare, NewsQ Pro, and Media Manager are either
registered trademarks or trademarks of Grass Valley, Inc. in the United States and/or other
countries. Grass Valley, Inc. products are covered by U.S. and foreign patents, issued and
pending. Additional information regarding Grass Valley, Inc. trademarks and other proprietary
rights may be found at www.grassvalley.com. Other trademarks and logos used in this
document are either registered trademarks or trademarks of the manufacturers or vendors of
the associated products, such as Microsoft® Windows® operating system, Windows Media®
player, Internet Explorer® internet browser, and SQL Server™. QuickTime and the QuickTime
logo are trademarks or registered trademarks of Apple Computer, Inc., used under license
therefrom.
Revision Status
Rev Date Description
June 17, 2009 Initial release of the K2 Dyno Replay System Quick Start Guide—
071-8681-00
January 28, 2010 Updates for version 1.5 — 071-8681-01

28 January 2010 K2 Dyno Replay System Quick Start Guide 5
Chapter 1
Installation
This section documents the installation of the bundled K2 Summit Production Client
and K2 Dyno Replay Controller that you buy as a Dyno-Pack. If you are connecting
a K2 Solo Media Server or a K2 Summit Production Client that is not part of a
Dyno-Pack and has not been previously controlled by a K2 Dyno Controller, refer to
the K2 Dyno Controller Installation Manual.
Unpack and check contents
Find the following items in the packaging for the K2 Summit Production Client.
Find the following items in the packaging for the K2 Dyno Controller.
K2 Summit Production Client
Power cords
LTC cables
Release Notes
Licenses and
Warranties
Rack slides
Documentation CD
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
! rass ! all! ! ! roup
! rass ! all! ! ! roup
! rass ! all! ! ! roup
! rass ! all! ! ! roup
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
!!us!!s!!s
! rass ! all! ! ! roup
! rass ! all! ! ! roup
! rass ! all! ! ! roup
! rass ! all! ! ! roup
K2 SUMMIT PRODUCTION
CLIENT
NOTE: Do not lose the Recovery Flash
Drive that is stored inside the bezel.
It contains the image for this specific
K2 Summit Production Client.
K2 Dyno Replay Controller
Power cord
Keyboard
Mouse
Release Notes
Recovery Flash Drive
Licenses and
Warranties
Documentation CD
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
GrassValley Group
GrassValley Group
GrassValley Group
GrassValley Group
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
Aqusdgsgds
GrassValley Group
GrassValley Group
GrassValley Group
GrassValley Group
NOTE: Do not lose the Recovery Flash
Drive. It contains the image for this
specific K2 Dyno Replay Controller.

6K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 1 Installation
Gather additional items
To complete a typical K2 Dyno Replay System, as referenced in this Quick Start
Guide, you must provide the following items:
System overview
The procedures and explanations in this Quick Start Guide assume a typical K2 Dyno
Replay System, such as that illustrated in the following diagram. If your installation
requires a different system configuration, apply the information in this Quick Start
Guide accordingly.
• Two VGA monitors (1024 x 768
x 32 or greater) and cables
• Ethernet cable, either crossover or
straight-through
• Video monitors and cables • Audio monitoring system
• USB keyboard • USB mouse
K2 Summit Client
K2 Dyno Controller
Ethernet
connection
Video/audio monitoring
K2 SUMMIT PRODUCTION
CLIENT
SDI in (A)
C1
SDI out (C)
SDI out (D)
C3
PGM
P1
Record Play
PVW
P2
C4
SDI in (B)
C2
AppCenter Pro
on K2 Summit
Production Client
K2 Dyno Replay
application VGA
output

28 January 2010 K2 Dyno Replay System Quick Start Guide 7
Cable K2 Summit Client
Cable K2 Summit Client
If desired, mount the K2 Summit Client in an equipment rack. Refer to the K2 System
Guide for rack mount procedures.
Make K2 Summit Client cable connections as illustrated.
Each channel can be both an input (record channel) and an output (play channel). For
the K2 Dyno Replay System documented in this Quick Start Guide, C1 and C2 are
record channels and C3 and C4 are play channels.
Cable K2 Dyno Controller
Make K2 Dyno Controller cable connections as illustrated.
The Ethernet connection between the K2 Summit Client and the K2 Dyno Controller
can be via direct connect cable or via an Ethernet switch.
C1 C2 C3 C4
!
OK
~AC
!
OK
~AC
SDI IN1 SDI OUT1 SDI OUT2 LTC I/O
AES AUDIO RS422
SDI OUT1 SDI OUT2
USB/1394 100BT/1000BT
GPI
VGA REF. LOOP THROUGH
AES AUDIO RS422
LTC I/O
SDI IN2 SDI IN3 SDI IN1 SDI IN2 SDI IN3 SDI IN1 SDI OUT1 SDI OUT2 LTC I/O
AES AUDIO RS422
SDI OUT1 SDI OUT2
AES AUDIO RS422
LTC I / O
SDI IN2 SDI IN3 SDI IN1 SDI IN2 SDI IN3
Power
cord
Power
cord
AES
audio
Keyboard
and mouse
VGA
monitor
Channels (C1, C2, C3, C4) are bi-directional
Ethernet
Use C1 as
record channel.
Connect SDI in
Use C2 as
record channel.
Connect SDI in
Use C3 as
play channel.
Connect SDI out
Use C4 as
play channel.
Connect SDI out
100-240 V~
4A 50-60Hz
RS-232
Power
cord
Keyboard
and mouse
VGA
monitor
Ethernet

8K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 1 Installation
Start up K2 Dyno Controller
There is no logon for the K2 Dyno Controller.
Start up K2 Summit Client
Log on to the K2 Summit Client with the default Windows administrator account:
• Username: Administrator
• Password: adminK2
(The password is case sensitive)
At first startup, End User License Agreements appear on the K2 Summit Client
screen. Accept the agreements to continue.
The Power LED goes on and stays on. The Service LED stays off. Startup processes
complete in approximately two minutes and the K2 Summit Production Client is
ready for connection and operation.
100-240 V~
4A 50-60Hz
RS-232
Open
power
switch
door
Press
power
switch
K2 SUMMIT PRODUCTION
CLIENT
Press
standby
switch

28 January 2010 K2 Dyno Replay System Quick Start Guide 9
Configure network
Configure network
On both the K2 Summit Client and on the K2 Dyno Controller, use standard Windows
operating system procedures to configure a static IP address. IP addresses must be on
the same subnet. You can also configure a host name if desired.

10 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 1 Installation
Configure K2 Summit Client channels
Configure channels according to your required formats and resolutions.
For the default K2 administrator account, use the following to logon:
• Username: K2Admin
• Password: K2admin
(The password is case sensitive)
In Configuration Manager, click Channel and then select a channel tab to make
settings for 2 record 2 play mode as follows:
• Configure channels C1 and C2 as record channels. Make video and audio settings
as appropriate for your input.
• Configure channels C3 and C4 as play channels. Make video and audio settings as
appropriate for your output.
AppCenter
A
ppCenter
er
Open AppCenter and logon with the K2 administrator account. If a licensing message
appears, refer to K2 Release Notes.
Click System | Configuration.
Click tabs, buttons,
and scroll bar to
locate settings.
Select from drop-down
lists to make settings.
Click OK and Yes
to save settings.
1
2
3
4
5

28 January 2010 K2 Dyno Replay System Quick Start Guide 11
Monitor K2 Summit Client channels
Monitor K2 Summit Client channels
On the VGA monitor connected to the K2 Summit Client, you can monitor the four
channels. This requires an AppCenter Pro license.
You can also double-click on a monitor area in multi-view or control screen to switch
between views.
K2 SUMMIT PRODUCTION
CLIENT
In AppCenter, click View | Video Monitor
Toolbar
Full Screen
Video Monitor

12 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 1 Installation

28 January 2010 K2 Dyno Replay System Quick Start Guide 13
Chapter 2
Operation
Start a new session
Prerequisite: Dyno Server software must be installed on the K2 Summit/Solo. On the
K2 Summit Production Client that you receive with the K2 Dyno Replay System
(Dyno-Pack), it is pre-installed.
In approximately one minute the K2 Dyno Replay application should appear on the
touch screen and on the VGA screen.
Loop record can be set when you configure a Dyno session, and cannot be changed
during the active recording session. Exporting HL clips and Playlists is best done in
regular record mode (loop record off).
K2 Replay
Client
ay
K2 Replay
Client
On the K2 Dyno Replay Controller, open K2 Replay Client
1
Select
Configure
2
Select the K2 Summit
Client and Next
3
Select a new session
and Next
4
Set C1 and C2 to Recorder,
C3 and C4 to Player and
Next
5
Set C3 to PGM, C4 to
PVW and Start
6

14 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 2 Operation
View home page status
Select input and playout channels
To gang channels, press both P1 and P2 at the same time.
For more information about channel operation modes, refer to “Channel operation
overview” on page 25.
1Select Home tab 2Check available
storage
3Check audio
levels
1
Select A or B input
(camera angle)
M/E
PGM
Send
Goto
P1 P2
PVW
2
Select P1 or P2
playout

28 January 2010 K2 Dyno Replay System Quick Start Guide 15
Chapter 2 Operation
Replay
Press A or B to switch angles during playout.
Refer to “Controller buttons: Reference” on the inside back cover for more
information on button functions.
Live/Local button
Red = Live: You are watching the live video of the
selected channel being recorded.
Yellow = Local: You are controlling your replay in
still, slow motion, or normal playout mode.
The recording of the live video continues
while you are in this mode.
Shift button
Clear = Bottom function: For each button, the
function shown on the bottom of the button
label is currently active.
Yellow = Top function: For each button, the function
shown on the top of the button label is
currently active.
The Shift button also affects the function of controls displayed on the touch screen.
1
Start Record
(button lights red)
Record channel starts
recording
Player channel
program is controlled.
M/E
PGM
Send
Goto
P1 P2
PVW
2
Jog to playback point
Local
Live
Play
Slo Mo
playback
or
Fast
3
Local
Live
Local
Live
Shift
Tr i m
Ta k e
Shift
Tr i m
Ta k e

16 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 2 Operation
Capture highlight clip
M/E
PGM
Send
Goto
P1 P2
PVW
2Mark IN
4Mark OUT
To p
In
1 Locate IN point 3Locate OUT point
Btm
Out
Add highlight
to HL bin
Add Lib
Add HL
5
View
highlights on
Highlight tab
6
Change
highlight
views*
*Highlight views on VGA monitor:
Highlight clip plus metadata keywords
Highlight clip plus thumbnail
Highlight clips in table format
7

28 January 2010 K2 Dyno Replay System Quick Start Guide 17
Chapter 2 Operation
Add metadata
You can pre-make metadata keywords with the Dyno Keyword Editor application,
which you install on a separate PC. You then import K2 Dyno Editor files (XML) into
the Dyno Controller using the IMP/EXP soft key on the Config menu. See Import
page.
2Open the
metadata
screen
1 Select highlight
3Name highlight*
5Assign stars
(rating)*
*Keyboard shortcuts:
Name - Ctrl + 4
Keywords - Ctrl + 1, 2, 3
Rating - Ctrl + Space
4Select preset
keyword names*
6Select icon
7Return to
highlight screen

18 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 2 Operation
Play highlight clip
You can customize play operations as follows:
• On the VGA monitor click Auto Cue. In this mode, when you select a
highlight, it is automatically cued up.
• On the VGA monitor click Auto Play. In this mode, when you select a
highlight, it automatically plays.
• To configure play options, including pre-set play speed, on the controller touch
screen, press Shift and then touch PLAYOPT.
• To play at pre-set speed, press FN and then PLAY.
1 Select Highlight tab
4Play highlight.
2Select a highlight
3Cue highlight
M/E
PGM
Send
Goto
P1 P2
PVW
Fast
Match
Cue Up
Auto
Cue
Auto
Play
Shift
PLAYOPT
TIMELINE
Fn
Fast

28 January 2010 K2 Dyno Replay System Quick Start Guide 19
Chapter 2 Operation
Create a playlist: VGA interface
You can also move highlight clips within the playlist using the mouse.
Create a playlist: Controller interface
On the controller touch screen, select the Playlist tab to see the highlight clip added to
the playlist.
Click and drag
highlights into
playlist
1 Select Highlight tab 2
3
Select a highlight
Add highlight
to playlist
Press and hold Fn to select multiple highlights
and add to playlist in order selected
New PL
Add PL

20 K2 Dyno Replay System Quick Start Guide 28 January 2010
Chapter 2 Operation
Play a playlist with mix effects
Additional controls for mix effects are as follows:
• To select mix effects, press Shift . The Flying M/E button lights green when
M/E is on.
• To configure mix effects, such as duration times and transition types, touch the
CONFIG tab, scroll with < or >,and then touch M/E.
• Playlist target duration can be adjusted on the Playlist tab.
2
Select mix effects
M/E
PGM
Send
Goto
P1 P2
PVW
3
Play the playlist
with mix effects
4
Skip to next highlight
with flying mix effects
1
Cue playlist (press 3 times)
M/E
PL
M/E
PL
M/E
PL
++
M/E
PL
+
Fast
Tr i m
Ta k e
Shift
Shift
M/E