Great Little Trading Lollipop Kitchen L4011 User manual

1
Lollipop Kitchen
03/11/2016
V1
easy - medium - hard
Assembly Difculty
two-person job
L4011
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Not suitable for children under 3 years due to small parts that may
become detached and present a choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• Always use the wall strap provided.
• To avoid possible injury from tipping - DO NOT allow children to
climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Complies to the European Toy Safety Directive.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List
#1
1x Door
Catches
1x Door
Catches
4x Short
Screws
8mmL
10x Medium
Screws
16mmL
24x Long
Screws
21mmL
25x Barrel Nuts
7mm dia
You will need
(not supplied)
Phillips Head
Screwdriver
25x Barrel Nut
Bolts
40mmL
#2 #3 #4 #5
#6 #7
A B C D
E F G H
I J K L
M N O P
Q R S T
U V W X
Y Z AA AB
1x 1x 1x 1x
1x 1x 1x 1x
1x 1x 1x 1x
1x 1x 8x 1x
1x 1x 1x 1x
1x 1x 1x 1x
1x 1x 1x 1x
1x
AC
1x Anti-Tip Strap
AD

4
Hardware for Step 1:
4x #7 barrel nut bolts
STEP 1:
Attach panels C and D to panel A using 4x barrel nuts and
bolts.
4x #6 barrel nuts
#7
A
#7
#7
#7
STEP 2:
Now slide the base panel (B) into the grooves.
B
Drawer Assembly
Drawer Assembly
Drawer Assembly
E
#5
Hardware for Step 3:
4x #5 21mmL screws
STEP 3:
Attach drawer front (E) to panels D
and C using 4x long screws (#5).
Soap Drawer Assembly
STEP 4:
Attach the soap drawer rest (K) to the back of the
control panel (L) using 2x medium screws (#4).
Hardware for Step 4:
2x #4 16mmL screws
C
D
#6
#6
#6
#6
#5
#5
#5
K
L
#4
#4
C
D

5
Soap Drawer Assembly
STEP 5:
Attach panel G to panels I and J using 4x medium
screws (#4).
Hardware for Step 5:
4x #4 16mmL screws
Soap Drawer Assembly
STEP 6:
Now slide the base panel (H) into the grooves.
Soap Drawer Assembly
Side Panel Assembly
Hardware for Step 7:
4x #4 16mmL screws
STEP 7:
Push the part assembled drawer through the hole. Now slot the soap drawer
back (F) onto the part assembled drawer. Secure using 4x medium screws (#4).
Hardware for Step 8:
2x #5 21mmL screws
STEP 8:
Attach the 2x pegs (O) to the external face of panel M, using 2x long screws (#5).
J
I
G
#4
#4
#4
#4
H
#4 #4 #4
#4
F
M
O
O
#5
#5

6
Back Panel Assembly
STEP 9:
Attach the x6 pegs (O) to the front face of panel N, using 6x long screws (#5).
Hardware for Step 9:
6x #5 21mmL screws
Hardware for Step 10:
2x #5 21mmL screws
2x #3 8mmL screws
1x #2 door catch
Hardware for Step 11:
2x #5 21mmL screws
STEP 11:
Now attach tap section (S) to the worktop (R) using 2x long screws (#5).
STEP 12:
Attach the door catch (#1) to panel T using 2x short screws (#3).
Hardware for Step 12:
2x #3 8mmL screws
1x #1 door catch
O
#5
OOOOO
#5 #5 #5 #5 #5
N
STEP 10:
Attach the handle (Q) to the door (P) using 2x long screws (#5). Attach the
door catch (#2) to the door using 2x short screws (#3).
#5
#5
#3
#3
#2
Q
P
#5 #5
R
S
#3 #3
#1
T
Oven Door Assembly
Worktop Assembly
Dividing Panel Assembly

7
STEP 13:
Secure dividing panel T to panel X using 2x barrel nuts and bolts.
STEP 14:
Secure left hand side panel (M) to base panel V using 2x barrel nuts and bolts.
STEP 16:
Slide back panel (W) into the grooves on panels M, U and V.
Hardware for Step 13:
2x #7 barrel nut bolts
2x #6 barrel nuts
T
X
Hardware for Step 14:
2x #7 barrel nut bolts
2x #6 barrel nuts
#7
V
W
#6
#6
#7
#7
M
#7
#7
#6
#6
Hardware for Step 15:
2x #7 barrel nut bolts
2x #6 barrel nuts
STEP 15:
Secure right hand side panel (U) to base panel V using 2x barrel nuts and bolts.
#7
V
#7
#6
#6
U
M
U
V

8
X
STEP 17:
Carefully secure panel X assembly to panels M and U using 4x barrel nuts and bolts.
Hardware for Step 17:
4x #7 barrel nut bolts
4x #6 barrel nuts
M
U
#7
#6
#6 #6
#6
#7
#7
#7
STEP 18:
Slot the oven tray (Y) into the two slots located on the inside faces of panels
M and T.
Y
M
T
Hardware for Step 19:
4x #7 barrel nut bolts
4x #6 barrel nuts
STEP 19:
Position panel Z between
panels T and U, secure this
panel using 4x barrel nuts
and bolts.
Please do not fully tighten
right hand side barrel nuts
and bolts. You will need this
to complete step 21.
Please note the 4x barrel
nuts are inserted into the
holes on the back face of
panel Z.
Z
T
U
View of
panel Z from
the other side
STEP 20:
Locate the lower oven door hinge
on panel P into the hinge hole on
panel X.
Push the door shut, so the catches
engage.
Loosely tighten.
Do not fully tighten
P
X

9
STEP 21:
Position panel L into the dowel holes
on panels M and U, at the same time
ensure the top oven door hinge goes
into the hinge hole on panel L.
With panel L in position, now fully
tighten the right hand side barrel nuts
and bolts on panel U.
STEP 22:
Secure panel L to panel M using 2x long screws (#5).
Now secure panel L to panel T using 2x long screws (#5).
STEP 23:
Slide back panel (AA) into the grooves on panels M and U.
AA
Hardware for Step 22:
4x #5 21mmL screws
View of
panel T from
the other side
M
U
R
M
U
Hardware for Step 24:
4x #5 21mmL screws
#5
#5
#5
#5
L
M
U
L
Now fully
tighten
L
M
#5
#5
T
#5 #5
STEP 24:
Carefully lower the
worktop (R) onto panels
AA and L. The dowel on
the top face of panel L
should slot into the hole
on the underside of the
worktop (R).
Secure the worktop (R) into
position between panels M
and U using 4x long screws
(#5).

10
STEP 25:
Carefully slide backboard (N)
into the grooves on panels
M,N and R.
Secure this into place using 2x
barrel nuts and bolts.
Hardware for Step 27:
1x #7 barrel nut bolts
1x #6 barrel nuts
Hardware for Step 26:
6x #7 barrel nut bolts
6x #6 barrel nuts
M
U
N
AB
#7
#6
#7
#7
#7
#6
#6 #6
#6
#7
AD
STEP 26:
Whilst holding the shelf (AB)
into position. Secure into
place using 4x barrel nuts and
bolts.
Now secure the backboard in
place using 2x barrel nuts and
bolts.
STEP 27:
Attach the anti tip
strap (AD) to the back
of the unit using 1x
barrel nut and screw.
The barrel nut also
secures the shelf (AB)
into position.
The strap should now
be attached to the wall
using hardware that is
suitable for the walls
in your home (not
provided).
R
The help of a second
person may make this
step easier.
AC
STEP 28:
Insert the sink (AC) into the cut
out on the worktop.
Slide the assembled drawer along
the runners.
The assembly is now complete.
Copyright© 2017 G.L.T.C. Ltd. All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
#7
#7
#6
#6
AB