Gree U-Match UMAT18HP230V1AF User manual

FLOOR/CEILI G
I STALLATIO MA UAL
Models:
Indoor Unit Outdoor Unit
UMAT18HP230V1AF UMAT18HP230V1AO
UMAT24HP230V1AF UMAT24HP230V1AO
UMAT30HP230V1AF UMAT30HP230V1AO
UMAT36HP230V1AF UMAT36HP230V1AO
UMAT42HP230V1AF UMAT42HP230V1AO
UMAT48HP230V1AF UMAT48HP230V1AO

Table of Contents
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Suggested Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
System Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Standard Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
nstallation Site nstructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
ndoor Unit nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12
Outdoor Unit nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Piping nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17
Power and Wiring nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Testing and nspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26
Diagnostic Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-29
Thank you for choosing a
Universal Floor/Ceiling
Unit for your customer.
Please read this installation manual carefully before installing and starting up the
Universal Floor/Ceiling Ductless System. Take a moment to fill out the product and
installation form on the back cover. Retain both the manual and installation
record for future reference.

SAFETY PRECAUTIO S
Please read the following before installation.
This is the safety alert symbol. t is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
This mark indicates procedures which, if improperly performed,
might lead to the death or serious injury of the user.
This mark indicates procedures which, if improperly performed, might
possibly result in personal harm to the user, or damage to property.
Notice is used to address practices not related to personal injury.
General Safety Precautions
1. nstructions for installation and use of this product are provided by the manufacturer.
For proper operation, the system must be installed in accordance with this
installation manual.
2. nstallation must be performed in accordance with local laws, regulations and
National Electrical Codes (NEC).
3. f refrigerant leaks while work is being carried out, ventilate the area. Do not allow
refrigerant to come in contact with a flame as it produces toxic gas.
4. Disconnect all electrical power to the indoor and outdoor units until the system is
ready for start-up and checkout.
5. When installing or repairing the system, use only R410A refrigerant. Do not
mix refrigerant with other gases. f air or other gas enter the refrigeration system,
the pressure inside the system may rise to an abnormally high value and cause
damage or injury.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
WARNING
CAUTION
NOTICE
WARNING
2

Indoor Unit
Outdoor Unit
OME CLATURE
Example: UMAT18HP230V1AC
UMAT 18 1 A O
Series Designation
UMAT – U-Match Series
Product Type
S - System
O - Outdoor Units
H - Indoor High Wall
D - Indoor Duct
C - Indoor Cassette
F - Indoor Floor/Ceiling
Revision Level
Style/Color Designation
Electrical Rating
230V - 208/230V 60Hz 1PH
115V - 115V 60Hz 1PH
HP 230V
Cooling Capacity
18 - 18,000 BtuH
24 - 24,000 BtuH
30 - 30,000 BtuH
36 - 36,000 BtuH
42 - 42,000 BtuH
48 - 48,000 BtuH
Model Type
AC - Cooling Only
HP - Heat Pump
HC - Heat/Cool
Example: UMAT18HP230V1AO
F
F
3

SYSTEM REQUIREME TS
REFRIGERA T CHARGE
I DOOR U IT ELECTRICAL REQUIREME TS
PIPE SIZE in (mm)
Notes: nsulate both refrigerant lines, separately.
Communication Cable: Recommended cable - 18/2 AWG stranded bare copper conductors THHN 600V unshielded wire
Note: Use shield cable if installation is in close proximity of RF and EM transmitting devices.
Unit Size
(BtuH)
18,000 1/4 (6) 1/2 (12) 10 (3) 25(7.5) 66 (20) 49 (15)
24,000 3/8 (10) 5/8 (15) 10 (3) 25(7.5) 98 (30) 49 (15)
30,000 3/8 (10) 5/8 (15) 10 (3) 25(7.5) 98 (30) 49 (15)
36,000 3/8 (10) 5/8 (15) 10 (3) 25(7.5) 98 (30) 49 (15)
42,000 3/8 (10) 5/8 (15) 10 (3) 25(7.5) 164 (50) 98 (30)
48,000 3/8 (10) 5/8 (15) 10 (3) 25(7.5) 164 (50) 98 (30)
Min Line
Max. Pre-Charge
Max Line Max Elevation
Length Line Length Length (ID over OD)
Liquid Suction/Gas
Line Line
Unit Size Refrigerant Factory System Additional
(BtuH) Type Charge oz (kg)* Charge oz/ft (g/m)
18,000 R410A 49.4 (1.4) 0.3 (30)
24,000 R410A 77.6 (2.2) 0.6 (60)
30,000 R410A 84.7 (2.4) 0.6 (60)
36,000 R410A 123.5 (3.5) 0.6 (60)
42,000 R410A 130.5 (3.7) 0.6 (60)
48,000 R410A 141.1 (4.0) 0.6 (60)
Unit Size Voltage Min Circuit Max Overcurrent Main Power
(BtuH) Amps (MCA) Protection (MOCP) Wire Size (AWG)
18,000 208/230v - 1ph 60hz 1.0 15 14
24,000 208/230v - 1ph 60hz 1.5 15 14
30,000 208/230v - 1ph 60hz 2.0 15 14
36,000 208/230v - 1ph 60hz 2.0 15 14
42,000 208/230v - 1ph 60hz 2.0 15 14
48,000 208/230v - 1ph 60hz 3.0 15 14
OUTDOOR U IT ELECTRICAL REQUIREME TS
Unit Size Voltage Min Circuit Max Overcurrent Main Power
(BtuH) Amps (MCA) Protection (MOCP) Wire Size (AWG)
18,000 208/230v - 1ph 60hz 17.0 25 10
24,000 208/230v - 1ph 60hz 24.0 40 10
30,000 208/230v - 1ph 60hz 24.0 40 10
36,000 208/230v - 1ph 60hz 29.0 45 8
42,000 208/230v - 1ph 60hz 31.0 50 8
48,000 208/230v - 1ph 60hz 45.0 70 6
*Precharge amount for up to 25-ft of refrigerant pipe.
REFRIGERA T LI E LE GTHS ft (m)
4

• Standard Wrench
• Adjustable/Crescent Wrench
• Torque Wrench
• Hex Keys or Allen Wrenches
• Drill & Drill Bits
• Hole Saw
• Pipe Cutter
• Screw drivers (Phillips & Flat blade)
• Manifold and Gauges
• Level
• R410A Flaring Tool
• Clamp on Amp Meter
• Vacuum Pump
• Safety Glasses
• Work Gloves
• Refrigerant Scale
• Micron Gauge
SUGGESTED TOOLS
5

6
Air inlet
SYSTEM PARTS
Indoor Unit
Part ame
1. Front Cabinet
2. Air nlet
3. Wired Controller
4. Remote Controller
5. Drain Pipe
6. Gas Pipe
7. Liquid Pipe
8. Service Cover
9. Front Panel
Outdoor Unit
Air outlet
Air inlet
9 8
3 4
1 2
76 5
The refrigerant pipe, drain pipe and electrical wiring for this unit should be installed by a
qualified HVAC professional only.
CAUTION
Air Outlet
Power
Supply

7
STA DARD PARTS
Indoor Unit Accessories
Outdoor Unit Accessories
o. ame Appearance Qty Usage
1 Nut with Washer 8 Secures the hook on the
cabinet of the unit
2 Remote Controller
and Battery 1+2 Controls the indoor unit
3 Cable Clamp 4 Fastens the insulation
blanket
4 Pipe nsulation 1 nsulates the gas pipe
5 Pipe nsulation 1 nsulates the liquid pipe
6 Template 2
For drilling holes for
mounting indoor unit
7 Flare Nut 1 Connects the gas pipe
8 Flare Nut 1 Connects the liquid pipe
o. ame Appearance Qty Usage
1 Drain Plug 3 Plugs the unused drain hole
2 Drainage Connecter
or 1Connects with field supplied
drain pipe

I STALLATIO SITE I STRUCTIO S
Indoor Unit
The unit must be installed in a location which can withstand four times the weight of the unit.
nadequate support may result in serious property damage and injuries.
Select a site that allows for the following:
•Ensure the installation complies with the installation minimum dimensions and meets the
minimum and maximum connecting piping length and maximum change in elevation.
• Air inlet and outlet should be clear of obstructions, ensuring proper airflow throughout the room.
• Condensate can be easily and safely drained.
• All connections can be easily made to outdoor unit.
• ndoor unit is out of reach of children.
• A structure strong enough to withstand four (4) times the full weight of the unit.
• Filter can be easily accessed for cleaning.
• Leave enough free space to allow access for routine maintenance.
• Do not install in a laundry room or by a swimming pool due to chemicals corroding indoor unit coil.
8
WARNING

I STALLATIO SITE I STRUCTIO S
Outdoor Unit
9
Do not install the unit at a location where the distance exceeds the maximum pipe length indicated
in the table. The maximum length of the connection pipe is listed in the System Requirements section.
CAUTION
WARNING
Outdoor Unit Minimum Distances
in (mm)
A 40 (1000)
B 20 (500)
C 20 (500)
D 80 (2000)
E 20 (500)
Air inlet
Air outlet
A
BC D
E
The unit should be installed level on a pad that can support twice the weight of the unit.
f the outdoor unit will be exposed to strong winds, it must be adequately secured.
1. nstall the outdoor unit at a location that is capable of withstanding twice the weight of the unit.
2. nstall the outdoor unit where it is convenient to connect refrigerant lines to the indoor unit.
3. nstall the outdoor unit where the condensate water can be drained unobstructed during the
heating mode to a safe location.
4. Do not locate the unit where the noise may be objectionable to neighbors.
5. Provide the space shown below, so that the air flow is not blocked and future service and
maintenance can be performed.
Select a site that allows the following:
Minimum Outdoor Clearances