Green-Go GGO-BEACON User manual

Beacon Quick Start Guide

Green-GO Beacon
Quick Start Guide
Product description
The Green-GO Beacon is a full colour signal indicator with a transparent casing and
bright interior LEDs that will emit a signal when receiving talks, cues or calls.
Features
• Multicolour signal light
• Reacts to all 32 channels of the selected user in user mode
• Will react to all signals sent to a group it is added to
• Powered by PoE (802.3af-2003 standard) from Ethernet port

Setup
The Beacon has a single-button, bicolour LED interface with quick access to the basic
functions. Further options can be set with the Green-GO update connection software.
To access the button functions, see the descriptions below.
Button functions
Cloning config
Press and hold the button for 10 seconds
à
The LED next to the button will rapidly flash green during the ten seconds. It will
then take the first config it finds on the network. It is advised to do this with only
one other config present on the network.
Setting Group mode and assigning a group
Press the button for 1 to 2 seconds
à
The LED next to the button will rapidly flash red to indicate pairing mode.
Send a call from another device to a group
à
The beacon will now be paired to this group and will report calls on that group.
Optional cue and talk reports can be set with the update connection software.
Setting user mode and assigning an user
Press the button for 1 to 2 seconds
à
The LED next to the button will rapidly flash red to indicate pairing mode.
Send a call from another device to a user
à
The beacon will now be paired to this user and will report calls on all channels of
that user. Optional cue and talk reports can be set with update connection.
Full reset to factory defaults
Press the button during powerup and release when powered up
à
This will start up the device in boot mode. The LED next to the button will rapidly
flash red to indicate that the device is in boot mode.
Press and hold the button for 30 seconds
à
During the countdown, the LED will alternate flashing red with green. The LED will
turn solidly green after 30 seconds, indicating that the device is now reset to
factory defaults. The LED will go back to flashing red when the device is ready.
Turn the device OFF and back ON
à
To return the device to normal operation.

Enhanced functions
Enhanced functions are available using the Green-GO update connection software.
To connect the device to the Green-GO update connection software, make sure the
computer is in the same IP range as the Beacon.
The default IP setting of a Beacon is set to dynamic. When no DHCP server is present,
the Beacon will get an IP address in the 169.254.xxx.xxx range. It is advised to set
your computer to a fixed address in this range – with a subnet of 255.255.0.0 – and
turn other network adaptors (like wifi) off.
When the device is connected, press the Scan button on the software. The Beacon
will now pop up in the left pane. By selecting the beacon, the properties will be
displayed in the right hand pane.
IP
Set up the IP of the Beacon
à
The default setting is dynamic, but a manual address and subnet can be set here.
This will be active immediately, therefore it might be necessary to change the
settings of the computer accordingly.
Dim
Set the intensity of the Beacon
à
The Beacon can be set to 3 intensity levels, corresponding to a change in brightness
of the LED outputs.
Backlight
Enable the Blue backlight
à
By enabling the backlight function, the display will always be lit up blue. This can be
useful for orientation or worklight purposes.
Talk light
Enable the talk activity report
à
The beacon can be set to not only report calls but also the talk activity of the
assigned group or user.

Colours
The colours of the different signals of the Beacon can be adjusted by changing the
global colour scheme of the Green-GO config used. This can be done in the Config
settings menu of the Green-GO control software.
Default Colors
Idle
à
Blue
Active
à
Yellow
Call
à
Red
Allert Call
à
Red/White flash
Attention
à
Yellow/Red flash
Cue GO
à
Green
LED status
Slow green flash
à
Ok, other devices found with the same config
Green with slow red flash
à
No other devices found with the same config
Rapid red flash
à
Pairing mode, waiting for call to set group or user
Rapid green flash
à
Button pressed, waiting for config to clone
Rapid red with short off time
à
Boot mode
Rapid red with short green
à
Boot mode, button pressed –
countdown for reset running
Factory default settings
The IP of the Beacon will be set to dynamic if it is reset to factory defaults.
With no DHCP server in the network, it will get a link-local IP address in the
169.254.xxx.xxx range with a subnet of 255.255.0.0.

Declaration of Conformity
We,
Manufacturers name: ELC Lighting b.v.
Manufacturers address: Weerijs 8
5422 WV Gemert
The Netherlands
Herewith take the full responsibility to confirm that the product
Product Category: Communication equipment
Name of product: GGO-BEACON
Which refer to this declaration are manufactured in the Netherlands and complies with the
following product specifications and harmonized standards:
Safety: LVD (Low Voltage Directive) 2014/35/EU, EN62368-1
EMC: 2014/30/EG, EN55032
ROHS (II): 2011/65/EU
With the presumption that the equipment is used and connected according to the manual,
supplied with the equipment. All signal input- and output connections must be shielded and
the shielding must be connected to the ground of the corresponding plug.
Gemert, February 16, 2018
ing. Joost van Eenbergen