Greenheck SP 210-258 User manual

Parts List
1. Duct Connector
2. Backdraft Damper Assembly
3. Discharge Cover Plate
4. Grille (SP)
5. Bottom Panel (CSP)
6. Mounting Angles
7. Housing
8. Power Assembly:
A. Scroll
B. Venturi
C. Wheel
D. Motor
E. Drive Frame
9. Insulation
10. Internal Receptacle and Bracket
11. Electrical Junction Cover Plate
Tools Required - Phillips head
screwdriver and wrenches.
9
1
11
3
7
10
9
5
4
6
8C
8E 8A 8D
8B
2
9
SP/CSP 210-258 SP/CSP 260-280
2
11
1
1
3
3
7
9
9
9
6
8A
8D
8A
8B
8C
8C
8B
8B
8B
10
8E
WARNING !
To reduce the risk of fire, electric shock, or injury to persons, observe the following:
• Fan Models SP/CSP 210 - 260 should only be used with fan speed control Part No.
KBWC-15K, manufactured by KB Electronics, Inc.
• Fan Models SP/CSP 262 - 275 should only be used with fan speed control Part No.
KBWC-112LK, manufactured by KB Electronics, Inc.
• Use this unit only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
• Before servicing or cleaning unit, switch power off at service panel and lock service
panel to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
• Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated construction.
• The combustion airflow needed for safe operation of fuel-burning equipment may be
affected by this unit's operation. Follow the heating equipment manufacturer's
guideline and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local code authorities.
• When cutting or drilling into wall or ceiling, do not damage electrical wiring or other
hidden utilities.
• This unit is not to be installed directly over a tub or shower.
• Ducted fans must always be vented to the outdoors.
CAUTION
For general ventilating use only.
Do not use to exhaust hazardous or explosive materials and vapors.
GREENHECK
P.O. BOX 410 SCHOFIELD, WISCONSIN 54476-0410
PH. 715-359-6171
www.greenheck.com
®
READ AND SAVE THESE INSTRUCTIONS
Models SP/CSP
Ceiling and
Cabinet Fans
PN 453669
Installation, Operation and Maintenance Manual

2
Ductwork and
Performance
Installation of ductwork is
critical to the performance
of these fans (see drawing).
Straight ductwork (1) or
ductwork that turns in the
same direction as the wheel
(2) is recommended.
Ductwork turning opposite
the wheel direction (3) will
cause turbulence and back
pressure resulting in poor
performance.
Note: If round duct is to be used, Model RDC
(Round Duct Connector) can be purchased from
Greenheck that bolt in place of the standard
square duct connector.
AIR FLOW
1
(GOOD)
3
(POOR)
2
(GOOD)
Sound and Location
The location of these fans must be taken
into consideration before installation. In
sound critical installations
insulated ductwork, flexible duct
connections or placing the fan in a
remote section of ductwork are solutions
to meeting the required fan sound levels.
Placement Near Cooking Equipment
These fans are not recommended for cooking
exhaust applications. They are designed primarily
for low temperature, clean air applications only. The
diagram shows the minimum distance these fans
should be placed in relation to cooking equipment.
Ductwork and Noise
Fiberglass ductboard is a better choice than
metal ductwork for reducing fan noise and is
highly recommended for low sound
applications. Where metal duct is used, sound
transmission can be reduced with flexible duct
connections between the fan and the duct.
Flex Duct
Connections
Metal Ductwork
Installation Recommendations
Airflow
CSP Mounting Arrangements
SP Ceiling Mounting
Arrangements
SP Wall Mounting
Arrangements
Airflow
Airflow
Airflow
Airflow
Airflow
Airflow
Airflow
Airflow
Airflow
Mounting
Arrangements
This illustration shows some
of the many configurations
SP and CSP fans can be
adapted to by simply
changing discharge
positions.
Fiberglass
Ductboard
Remote
Mounted
CSP
Correct Low
Sound Installation
Incorrect
SP Mounted
Directly
Overhead
Do not install
fan in this area
45°45°

3
Converting Duct Connector to
Vertical Discharge
This procedure is for SP/CSP single blower units sizes
210-258. This also applies to double blower units sizes
260-280 with some slight differences in the number of
fasteners and type and location of scroll mounting
brackets.
Step 1. Remove duct connector and cover plate.
Exchange their positions and secure with
fasteners. (See mounting arrangements on
page 2.)
Step 2. Remove grille (SP) or bottom panel (CSP).
Step 3. Unplug power cord from internal receptacle.
Step 4. Remove fasteners securing power assembly
bracket to housing (2 fasteners for SP/CSP
210-228; 4 for 250-258).
Step 5. Remove power assembly from housing, taking
care not to damage insulation.
For SP/CSP 250-258:
With power assembly removed, remove
gusset/bracket assemblies from fan scroll by
removing two fasteners on each side (do not
disassemble gusset/bracket assembly).
Fasten gusset/bracket assemblies on scroll in
position as shown in Photo B ( the opposite of
original position).
Step 6. Re-install power assembly (for all sizes).
- Plug power cord into internal receptacle.
- Insert power assembly into housing, matching
the scroll discharge with the housing duct
connector.
- Replace bracket fasteners and tighten.
Step 7. Replace grill or bottom panel.
Conversion is complete ready to install.
Grille and Bottom Panel Installation
Position the grille or bottom panel over the
housing opening as shown and secure with
fasteners provided.
Filters
The addition of an intake filter is highly
recommended for these fans, even in clean air
environments excess dirt can accumulate on
wheels and motors causing reduced performance
and imbalance.
Filters, once installed, should be checked and
cleaned periodically to maintain performance.
Greenheck offers washable aluminum mesh filters
specifically designed for these fans. Please consult
SP/CSP catalog for more information.
SP CSP
Step 2
(for procedure below)
Step 1
Step 4
Step 5 (for SP/CSP 250-258 only)
SP/CSP 210-228
HORIZONTAL DISCHARGE
SP/CSP 210-228 SP/CSP 250-258
VERTICAL DISCHARGE
A. B.
SP/CSP 250-258
Step 6

4
Electrical Connections
Figure below shows exterior electrical access cover for
field wiring. Connect electrical supply conduit through
one of the two knockouts illustrated. Connections are
made directly to black and white leads, a separate
green fastener is provided for ground wire connection.
Refasten cover when connections are complete.
Warranty
Greenheck warrants this equipment to be free from
defects in material and workmanship for a period of
one year from the purchase date. Any units or parts
which prove to be defective during the warranty
period will be replaced at our option when returned
to our factory, transportation prepaid.
The motor is warranted by the motor manufacturer
for a period of one year. Should the motor prove
defective during this period, it should be returned to
the nearest authorized motor service station.
Greenheck will not be responsible for any
installation or removal costs.
General Maintenance Suggestions
Models SP and CSP ceiling exhaust fans require very little
maintenance. However, since small problems over time left
unchecked could lead to loss of performance or early motor
failure, we do recommend that the unit be inspected
periodically (once or twice a year).
The fan motor and wheel(s) should be checked for dust and
dirt accumulations. (See Filters on page 3). Dirt buildup can
lead to loss of performance and motor overheating. Cleaning
can be accomplished by brushing off any dust that may have
accumulated. Even filtered units can accumulate build up
and should be checked when cleaning filters.
The motor should be checked for lubrication at this time.
Lubricate only those motors which have an oil hole provided.
A few drops of all-purpose oil (SAE 20) will be sufficient.
Mounting Brackets
Mounting brackets are convertible to
provide a wide range of adjustment
for both solid mounting or hanging
installations.
Angle mounting holes are slotted
where bracket attaches to housing to
allow for finer adjustment when
installations such as flush mounts in
ceilings or walls are required.
Hanging Vibration Isolators
Isolator kits, available from Greenheck, are
highly recommended to insure quiet, vibration-
free installations of these fans. The kits consist
of items shown except threaded ready rod
which is provided by others. Mounting angles
are prepunched for these kits.
GREENHECK
P.O. BOX 410 SCHOFIELD, WISCONSIN 54476-0410
PH. 715-359-6171
www.greenheck.com
®
®
SP/CSP models shown are UL and
cUL listed E 33599 Maximum
airstream temperature not to
exceed 95°F.
SP/CSP models shown are CSA
certified LR-34470 models 210-280
IOM SP/CSP FS
Rev. 2
September 1999
C
Top Mount
Bottom Mount
Brackets can be
used in either
position to adapt to
most mounting
situations
Bottom Mount
Slots in the
brackets
allow fine
adjustment
for flush
fit with
wall/ceiling
opening
Isolator Kit
Components
10/32 Threaded Rod
(Supplied By Others)
Knockouts
Electrical
Access
Panel