GreenWorks G24LT30 User manual

OBSLUHU / Uporabniški priročnik / PRIRUČNIK ZA RUKOVANJE / HASZNÁLATI
G24LT30
OPERATOR MANUAL / BEDIENUNGSHANDBUCH / MANUAL DEL OPERARIO /
MANUALE DELL’OPERATORE / MANUEL OPÉRATEUR / MANUAL DE UTILIZAÇÃO /
/ KULLANIM KILAVUZU /
KASUTUSJUHEND
STG311
Instrukcijutulkojumsnooriģinālvalodas/ Originaalkasutusjuhenditõlge
/
samitrev
Tercümesi/ / sojickurtsnisoilanigirO
οδηγίες/ / Orijinal Talimatların
Αυθεντικές
Traducerea instrucțiunilororiginale/ Преводнаоригиналнитеинструкции/ izvornihuputa/ Azeredetiutasítás fordítása/Prijevod
oryginalnej instrukcji/ Překladoriginálníhonávodu/ Prekladoriginálnehonávodu/ Prevodoriginalnihnavodil/Tłumaczenie
vejledninger/ohjeiden Översättningavoriginalinstruktionerna/ Produsentensinstruksjoner/ Oversættelseafde originalekäännös/
OriginalInstructions/ ÜbersetzungderOriginalanweisungen/ Traduccióndelasinstruccionesoriginales/ Traduzionedelleistruzionioriginali/
instructionsd'origine/ Traduzidoapartirdasinstruçõesoriginais/ Vertalingvandeoriginelegebruiksaanwijzing/ Alkuperäisten
Traduction des
GEBRUIKSAANWIJZING / KÄYTTÖOPAS / ANVÄNDARHANDBOK / BRUKERVEILEDNING /
BRUGSVEJLEDNING / INSTRUKC JA UŻYTKOWNIKA / NÁVOD K OBSLUZE / NÁVOD NA
ÚTMUTATÓ / MANUAL DE UTILIZARE /

DECLARATION OF CONFORMITY (UK)
Name and address of the manufacturer:
Name: GLOBGRO AB Globe Group Europe
Address: Riggaregatan 53, 211 13 Malmö Sweden
Name and address of the Authorized representative:
Name: Garden Equipment Ltd
Name and address of the person authorised to compile the technical file:
Name: Simon Del-Nevo
Address: First Floor, 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK
Here with we declare that the product
Category: Electric String Trimmer
Serial number: See product rating label
Year of Construction: See product rating label
• Is in conformity with the relevant provisions of the Supply of Machinery (Safety) Regulations 2008.
• Is in conformity with the provisions of the following other UK legislation:
• Electromagnetic Compatibility Regulations 2016
• Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012
Furthermore, we declare that the following standard have been used:
• BS EN 60335-1, BS EN 50636-2-91, BS EN 62233, BS EN 55014-1, BS EN 55014-2,
BS EN ISO 3744, ISO 11094, BS EN 62321-3-1, BS EN 62321-4, BS EN 62321-5,
BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2, BS EN 62321-8
Conformity assessment method to Annex E Noise Emission in the Environment by Equipment for use
Outdoors Regulations 2001
String trimmer:
Measured sound power level 93.1 dB(A)
Guaranteed sound power level
96 dB(A)
Place, date: Christchurch, Dorset, UK 11.11.2022
Signature: Ted Qu, Quality Director
Model: G24LT30 ( STG311 )
Address: First Floor, 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK

1 2 3
45
678
910
12
2
1
5
6
7
8
3
4
11
10
9
13
10
8
13
3
15
14
16
1
2
11
5

12 13 15
16
14
18
19 20 21
A
B
C
17
17 18
19
20
21
22
90°

1 Description............................. 4
1.1 Purpose...........................................4
1.2 Overview.........................................4
2 General power tool
safety warnings......................4
3 Installation..............................4
3.1 Unpack the machine....................... 4
3.2 Attach the guard............................. 4
3.3 Attach the wheel............................. 4
3.4 Attach the auxiliary handle..............5
4 Operation................................5
4.1 Install the battery pack....................5
4.2 Remove the battery pack................5
4.3 Start the machine............................5
4.4 Stop the machine............................5
4.5 Adjust the length of the shaft.......... 5
4.6 Operation tips..................................5
4.7 Cutting tips......................................5
4.8 Adjust the length of the
cutting line.......................................5
4.9 Line cut-off blade............................ 6
4.10 Change to the edging mode........... 6
5 Maintenance........................... 6
5.1 General information........................ 6
5.2 Clean the machine..........................6
5.3 Replace the spool........................... 6
5.4 Replace the cutting line.................. 7
6 Transportation and
storage....................................7
6.1 Move the machine.......................... 7
6.2 Store the machine...........................7
7 Troubleshooting.....................8
8 Technical data........................ 9
9 Warranty..................................9
10 EC Declaration of
conformity.............................. 9
3
English EN

1 DESCRIPTION
1.1 PURPOSE
This machine is used to cut grass, light weeds, and
other similar vegetation at or around ground level. The
cutting plane must be approximately parallel to the
ground surface. It also can be used to trim and cut
around the edge of driveways, side walks and more.
1.2 OVERVIEW
Figure 1 - 21.
1Lock-out button
2Trigger
3Auxiliary handle
4Upper shaft
5Telescopic adjustment
6Lower shaft
7Cut-off blade
8Flower guard
9Trimmer head
10 Support wheel
11 Guard
12 Slot
13 Screw hole
14 Knob
15 Bolt
16 Battery release button
17 Spool cover
18 Tab
19 Spool
20 Spool housing
21 Anchor hole
22 Guide slot
ADirection of rotation
BBest cutting area
CDangerous cutting area
2 GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
3 INSTALLATION
3.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine
before use.
WARNING
• If parts of the machine are damaged, do not use
the machine.
• If parts are missing, do not operate the machine.
• If parts are damaged or missing, contact the
service center.
1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in
compliance with local regulations.
WARNING
For your personal safety, do not insert battery before
the tool is assembled completely.
3.2 ATTACH THE GUARD
Figure 2 - 3.
WARNING
Do not touch the cut-off blade.
1. Pull the edge guide until the open end on the slot.
2. Remove the screw from the guard with a Phillips
head screwdriver (not included).
3. Put the guard onto the trimmer head.
4. Align the screw hole on the guard with the screw
hole on the trimmer head.
5. Tighten the screw.
3.3 ATTACH THE WHEEL
Figure 4 - 5.
1. Remove the screw from the wheel with a Phillips
head screwdriver (not included).
2. Put the wheel onto the trimmer head.
3. Align the screw hole on the wheel with the screw
hole on the trimmer head.
4
English
EN

4. Tighten the screw.
3.4 ATTACH THE AUXILIARY HANDLE
Figure 6 - 8.
1. Remove the knob from the handle.
2. Attach the auxiliary handle on the shaft.
3. Set the auxiliary handle in the comfortable
position.
4. Tighten the auxiliary handle with the knob.
4 OPERATION
IMPORTANT
Before you operate the machine, read and
understand the safety regulations and the operation
instructions.
WARNING
Be careful when you operate the machine.
4.1 INSTALL THE BATTERY PACK
Figure 9.
WARNING
• If the battery pack or charger is damaged, replace
them directly.
• Stop the machine and wait until the motor stops
before you install or remove the battery pack.
• Read, understand, and follow the instructions in
the battery and charger manual.
1. Align the lift ribs on the battery pack with the
grooves in the battery slot.
2. Push the battery pack into the battery slot until
the battery pack locks into place.
3. When you hear a click, the battery pack is
installed.
4.2 REMOVE THE BATTERY PACK
Figure 9.
1. Push and hold the battery release button.
2. Remove the battery pack from the machine.
4.3 START THE MACHINE
Figure 10.
1. Push the lock-out button and pull the trigger.
4.4 STOP THE MACHINE
Figure 10.
1. Release the trigger to stop the machine.
4.5 ADJUST THE LENGTH OF THE SHAFT
Figure 11.
NOTE
You can adjust the length of the shaft to operate the
machine easily.
1. Stop the machine.
2. Unlock the cam lever and move the lower shaft to
the desired position.
3. Lock the cam lever.
4.6 OPERATION TIPS
Figure 12.
WARNING
Keep clearance between the body and the machine.
WARNING
Do not operate the machine without guard in place.
Follow these tips when you use the machine:
• Keep a firm hold with both hands on the machine
while you operate the machine.
• Cut tall grass from the top down.
If grass winds around the trimmer head:
• First, remove the battery pack.
• Then, remove the grass.
4.7 CUTTING TIPS
Figure 15.
• Tilt the machine towards the area to be cut. Use the
tip of the cutting line to cut grass.
• Move the machine from right to left to prevent
thrown debris toward the operator.
• Do not cut in dangerous areas.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and
breakage. Stone and brick walls, curbs, and wood
can wear the cutting line quickly.
4.8 ADJUST THE LENGTH OF THE CUTTING
LINE
Figure 10
5
English EN

NOTE
The machine has an auto-feed head. If the cutting
line does not automatically advance, it can be
tangled or empty.
1. Start the machine and keep 3s. Release the
trigger until the machine totally stops.
2. Repeat the above step until you can hear the
line-cutting noise.
NOTE
The line will extend approximately 1 cm with each
stop and start of the switch trigger until the line
reaches the cut-off blade and the cut-off blade cuts
the excess length.
NOTE
Do not pull or release the trigger too fast.
NOTE
It will damage the machine if you hit the head to try
to advance the line.
4.9 LINE CUT-OFF BLADE
Figure 1.
This trimmer is equipped with a line cut-off blade
on the guard. The line cut off blade continuously
trims the line to ensure a consistent and efficient cut
diameter. Advance line whenever you hear the engine
running faster than normal, or when trimming efficiency
diminishes. This will maintain best performance and
keep the line long enough to advance properly.
4.10 CHANGE TO THE EDGING MODE
Figure 14 - 15.
NOTE
You can change the machine to a well groomed
edger for edging patios, driveways and walkways or
other areas.
1. Stop the machine.
2. Push on the edge button and rotate the trimmer
head until the guard and the shaft are parallel.
3. Unlock the cam lever and turn the trimmer head
90 degrees until the trimmer head locks into
position.
4. Lock the cam lever.
5 MAINTENANCE
IMPORTANT
Read and understand the safety regulations and the
maintenance instructions before you clean, repair or
do the maintenance work on the machine.
IMPORTANT
Make sure that all nuts, bolts and screws are tight.
Check regularly that the handles are firmly mounted.
IMPORTANT
Use only the replacement parts and accessories of
the initial manufacturer.
5.1 GENERAL INFORMATION
IMPORTANT
Only your dealer or approved service center can do
the maintenance that is not given in this manual.
Before the maintenance operations:
• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Use correct clothing, protective gloves, and safety
glasses.
5.2 CLEAN THE MACHINE
• Clean the machine after each use with a moist cloth
dipped in neutral detergent.
• Do not use aggressive detergents or solvents like
"glass cleaner" to clean the plastic parts or handles.
• Keep the trimmer head free from grass, leaves, or
excessive grease.
• Keep the air vents clean and free of debris to avoid
overheating and damage of the motor.
• Do not spray water onto the motor and electrical
components.
5.3 REPLACE THE SPOOL
Figure 16 - 18.
1. Simultaneously press the tabs on the sides of the
trimmer head.
2. Pull and remove the spool cover.
3. Remove the spool.
4. Replace with a new spool.
6
English
EN

NOTE
Make sure that the cutting line is in the guide slot
on the new spool, and is extended approximately 13
cm. before you install the new spool.
5. Put the end of the cutting line through the eyelet.
6. Extend the cutting line to release it from the guide
slot in the spool.
7. Push the tabs and install the spool cover onto the
spool housing.
8. Push the spool cover until it clicks into position.
5.4 REPLACE THE CUTTING LINE
Figure 19 - 21.
NOTE
Remove the remaining cutting line on the spool.
NOTE
Use only with the nylon cutting line of 1.65 mm
diameter.
1. Cut a piece of cutting line approximately 3 m
long.
2. Bend one end of the line approx. 6 mm.
3. Insert the line into the anchor hole of the spool.
4. Wind the cutting line around the spool tightly in
the indicated direction.
IMPORTANT
Failure to wind the line in the indicated direction will
cause the trimmer head to operate incorrectly.
5. Put the cutting line in the line slot.
6. Do not wind the cutting line beyond the edge of
the spool.
6 TRANSPORTATION AND STORAGE
WARNING
Remove the battery pack from the machine before
transportation and storage.
6.1 MOVE THE MACHINE
When you move the machine, you must:
• Wear gloves.
• Stop the machine.
• Remove the battery pack.
• Assemble the blade guard.
6.2 STORE THE MACHINE
• Remove the battery pack from the machine and
charge it.
• Make sure that children cannot come near the
machine.
• Keep the machine away from corrosive agents such
as garden chemicals and de-icing salts.
• Secure the machine during transportation to prevent
damage or injury. Clean and examine the machine
for any damage.
7
English EN

7 TROUBLESHOOTING
Problem Possible Cause Solution
The machine does not
start when the trigger is
pushed.
No electrical contact between the
machine and the battery pack.
1. Remove battery pack.
2. Check contact and install the battery pack
again.
The battery pack is depleted. Charge the battery pack.
The lock-out button and trigger are
not pushed at the same time.
1. Pull the lock-out button and hold it.
2. Pull the trigger to start the machine.
The machine stops
when you are cutting.
The guard is not attached to the ma-
chine.
Remove the battery pack and attach the guard to
the machine.
Heavy cutting line is used. Use only with the nylon cutting line of 1.65 mm
diameter.
The grass winds around the motor
shaft or the trimmer head.
1. Stop the machine.
2. Remove the battery pack.
3. Remove the grass from the motor shaft and
trimmer head.
The motor is overloaded. 1. Remove the trimmer head from the grass.
2. The motor will recover to work as soon as the
load is removed.
3. When you cut, move the trimmer head in and
out of the grass to be cut and remove no more
than 20 cm in pass.
The battery pack or machine is too
hot.
1. Cool the battery pack until its function returns
to normal.
2. Cool the machine for approximately 10 mi-
nutes.
The battery pack is disconnected
from the tool.
Install the battery pack again.
The battery pack is depleted. Charge the battery pack.
The line does not ex-
tend.
Lines are welded to themselves. Lubricate with silicone spray.
Not enough line on the spool. Install more line.
Lines are worn and too short. Extend the line.
Lines are tangled on the spool. 1. Remove the lines from the spool.
2. Wind the lines.
8
English
EN

Problem Possible Cause Solution
The line keeps break-
ing.
The machine is used incorrectly. 1. Cut with the tip of the line, avoid stones, walls
and other hard objects.
2. Advance the cutting line regularly to keep full
cutting width.
The grass winds
around the trimmer
head and motor hous-
ing.
Cut tall grass at ground level. 1. Cut tall grass from the top down.
2. Remove no more than 20 cm in each pass to
prevent wrapping.
The line does not cut
well.
The cut-off blade becomes dull. Sharpen the cut-off blade with a file or replace it.
8 TECHNICAL DATA
Voltage 24 V
No load speed 8500±10% RPM
Cutting head Automatic feed
Cutting line diame-
ter
1.65 mm
Cutting path diame-
ter
305 mm
Weight (without
battery pack)
2.35 kg
Measured sound
pressure level
LPA=92 dB(A), KPA= 3 dB(A)
Guaranteed sound
power level
LWA.d= 96 dB(A)
Vibration 3.7 m/s2, k=1.5 m/s2
Battery model G24B2 and other BAG series
Charger model G24UC2 and other CAG ser-
ies
Noise value.
9 WARRANTY
(The full warranty terms and conditions can be found
on Greenworks website www.greenworkstools.eu)
The Greenworks warranty is 3 years on the product,
and 2 years on batteries (consumer/private usage)
from the date of purchase. This warranty covers
manufacturing faults. A faulty product under warranty
might be either repaired or replaced. A unit that has
been misused or used in other ways then described
in the owner’s manual might be rejected for warranty.
Normal wear, and wear parts are not considered as
warranty. The original manufacturer warranty is not
affected by any additional warranty offered by a dealer
or retailer.
A faulty product must be returned to the point of
purchase in order to claim for warranty, together with
the proof of purchase (receipt).
10 EC DECLARATION OF CONFORMITY
Name and address of the manufacturer:
Name: GLOBGRO AB
Globe Group Europe
Address: Riggaregatan 53 211 13 Malmö, Swe-
den
Name and address of the person authorised to compile
the technical file:
Name: Micael Johansson
Address: Riggaregatan 53 211 13 Malmö, Swe-
den
Herewith we declare that the product
Category: Grass trimmer
Model: G24LT30 ( STG311 )
Serial number: See product rating label
Year of Construction: See product rating label
• is in conformity with the relevant provisions of the
Machinery Directive 2006/42/EC.
9
English EN

• is in conformity with the provisions of the following
other EC-Directives:
• 2014/30/EU
• 2000/14/EC & 2005/88/EC
• 2011/65/EU & (EU)2015/863
Furthermore, we declare that the following (parts/
clauses of) harmonised standards have been used:
• EN 60335-1; EN 50636-2-91; EN 62233; EN
55014-1; EN 55014-2; EN ISO 3744; ISO 11094;
IEC 62321-7-2; IEC 62321-4; IEC 62321-5;
IEC 62321-6; IEC 62321-7-1; IEC 62321-8; IEC
62321-3-1
Conformity assessment method to Annex VI / Directive
2000/14/EC.
Grass trimmer
Measured sound power
level:
LWA=93.1 dB(A)
Guaranteed sound power
level:
LWA.d=96 dB(A)
Place, date: Signature: Ted Qu, Quality Di-
rector
Malmö,
10
English
EN