GREISINGER BaleCheck 200 User manual

H60.0.71.6C-01
GMH Messtechnik GmbH • Standort Greisinger
as of version 1.8 BaleCheck 200 with GMH 38
Operating Manual Appendix
Hay and straw humidity measuring device
WEEE-Reg.-Nr. DE 93889386

H60.0.71.6C-01 Operating Manual Appendix BaleCheck 200 with GMH 38 page 2 of 4
_____________________________________________________ _____________________________________________________________________________
1 General Note
Read this document carefully and get used to the operation of the device before you use it.
Keep this document within easy reach near the device for consulting in case of doubt.
Mounting, start-up, operating, maintenance and removing from operation must be done by qualified, specially trained
staff that have carefully read and understood this manual before starting any work.
The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended one, ignor-
ing this manual, operating by unqualified staff as well as unauthorized modifications to the device.
The manufacturer is not liable for any costs or damages incurred at the user or third parties because of the usage or
application of this device, in particular in case of improper use of the device, misuse or malfunction of the connection
or of the device.
The manufacturer is not liable for misprints.
2 Intended Use
The BaleCheck 200 is a complete set for material moisture measuring including an handheld in-
strument (GMH 3830) with moisture display and rating.
The slim and robust measuring probe (GSF 40 TF) makes the set a first-class tool for humidity
measurements of pressed straw or hay (bales) and grain.
The measuring probe included to the set is connected to the device by a BNC-plug and Thermo-
couple plug.
Depending on the application either the material moisture u (based on dry matter) or the water con-
tent w (based on wet total mass) can be displayed.
Please consider the information “Measuring precision” in chapter 5.4
3 Product Specification
3.1 Scope of supply
The set includes:
Measuring probe GSF 40 TF
Handheld meter GMH 3830 incl. 9V battery and Operating Manual
Protection bag ST-KR
Operating Manual Appendix BaleCheck 200
3.2 The measuring probe GSF 40 TF
isolator
probe tip with
temp. sensor probe tube
100
minimum immersion

H60.0.71.6C-01 Operating Manual Appendix BaleCheck 200 with GMH 38 page 3 of 4
_____________________________________________________ _____________________________________________________________________________
4 Handling
4.1 Start of operation
Switch the device on with the on/off key. After segment test the device is ready for measuring.
4.2 Selection of the characteristic curve
Selection of characteristic curve: by pressing the characteristic curve can be selected.
The use of inappropriate characteristics can cause faulty measurements!
Selectable material characteristics: (via “Sort”-function preselected, please refer to operating manual GMH 38xx)
4.3 Temperature Measurement
The Temperature value will be displayed temporarily when key is pressed.
Let the Probe adjust to the material for at least 20 seconds to achieve good measuring precision
5 Principles of the measurements
5.1 Moisture rating ( WET - MEDIUM - DRY )
In addition to the measuring value there is a moisture rating via bar graph.
This rating can only be a first approximate value, because factors like the application
field of the measured material have to be taken into account for the final rating.
Experience and knowledge can only be supported by this instrument, not replaced!
5.2 Moisture u and water content w
Either moisture u or water content w is needed according to the application. The BaleCheck 100 is
supposed to be used the unit moisture u (relating to oven-dry mass). In some cases, like rating of
combustibles, the water content w may be more suitable.
The instrument can be configured to both of the values, please refer to GMH 38xx manual.
Moisture u (relating to oven-dry mass) –recommended setting
The unit is %u (also common: % atro, weight percent)
Example: 1 kg wet hay that contains 500 g water has a moisture u of 100%
Water content w (= moisture relating to wet total mass, please refer to operating manual GMH 38xx)
5.3 Temperature compensation
The temperature compensation is important for a reliable moisture-measuring.
There for the device features a temperature measuring at the Tip of the injection probe.
According to the selected material characteristic curve the device will use the associated tempera-
ture compensation.
Display Characteristic curve

By means of additional equipment (not within scope of
supply) wood and building materials of many kinds can
be measured –therefore the user has to add the refer-
ring characteristic curves to the Sort- Preselection, or
deactivate it complete.
R E F Reference characteristic
h.462 Wheat
h.463 Barley
h.464 Hay
h.465 Straw
moisture u[%] = ( (mass wet - mass dry ) / mass dry) *100
o
r: m
oisture u[%] = (
m
ass water
/ mass
dry) *100



H60.0.71.6C-01 Operating Manual Appendix BaleCheck 200 with GMH 38 page 4 of 4
_____________________________________________________ _____________________________________________________________________________
5.4 Measuring Practice
The measuring values
For storability and evaluation of quality and purpose the BaleCheck measuring is a valuable deci-
sion support –Beside other criteria like smell (mouldy?)–consistency (dust…) and look (color,
dirt…).
For freshly harvested material like straw, hay and grain the following can be recommended:
below 16 % uMaterial is sufficiently dry and storable
16 - 20 % u Material contains significant moisture, eventually dry it before storage
above 20 % u Material contains excess moisture, stop harvesting if possible!
Irregular moisture distributions
Please consider: depending on storage and harvesting procedure, there can be irregular distribu-
tions of moisture within the bales or grain heaps/stores.
Measuring precision
The BaleCheck 200 is designed for approximate determination of material moisture in hay, straw
and grain. Depending on state and sort of material there may be deviations. The strength of the
measuring system lies within the ability, due to the construction and usability, to gather fast and
comfortably many measurements spread over the bale/store (deep inside, at the floor, at critical
weathered places..) –in practical use this often is much more valuable than single precision meas-
urements and also is a valuable supplement to single precision measurements!
Minimum immersion / minimum amount of material
For best measuring results, the black isolator at the probe tip has to be completely immersed into
the material plus at least 5 cm of the stainless steel shaft has to be in good contact to the material.
When measuring grain, try to use at least ~ 500ml of grain, covering the probe tip and ensure to
have enough contact/compressed grain around the probe –In heaps/stores higher than 30 cm and
minimum immersions of 20 cm no additional measures have to be taken; otherwise the measure-
ment values may be too low.
Keep probe clean!
Especially when measuring in wet hay, the probe may be soiled very strong, this may produce to
low measuring displays.
Soilded probe -> wrong measuring!
In hard cases we suggest fine grinding fleece o rat least suitable household sponges for cleaning.
Do not use steel wool!
Display values at air
If the probe is not correctly in contact to material, the instrument may display any value!
This is caused by the design and measurement method.
At values above 25% u the measurement precision decreases!
But decision making in this range is: Wet is wet, no matter how wet!