GREISINGER G 1107 User manual

Quick reference guide
G 1107 / G 1113
Fine manometer | manometer
EN

Table of contents
24 / 44 B-H88.0.2X.DKZ-1.0
Table of contents
1 About this documentation........................................................... 26
1.1 Purpose of the document................................................................26
1.2 Legal notices...................................................................................26
1.3 Further information..........................................................................26
2 Safety............................................................................................. 27
2.1 Explanation of safety symbols ........................................................27
2.2 Foreseeable misuse........................................................................27
2.3 Safety instructions...........................................................................28
2.4 Intended use ...................................................................................28
3 The product at a glance ............................................................... 29
3.1 The G 1100 manometer series .......................................................29
3.2 Display elements.............................................................................29
3.3 Operating elements.........................................................................29
3.4 Connections....................................................................................30
4 Operation ...................................................................................... 31
4.1 Opening the configuration menu.....................................................31
4.2 Open the adjustment menu.............................................................33
5 Measurement Basics.................................................................... 34
5.1 Special functions.............................................................................34
5.1.1 NVLL Tare function ...........................................................................35
5.1.2 F,NE High-resolution measurement with 0.1 Pa (G 1107)...............35
5.1.3 F,NE High-resolution measurement with 1 Pa (G 1113)..................36
5.1.4 AVR 0:02 / AVR 0:05 / AVR 0: 10..........................................................36
6 Operation and maintenance ........................................................ 38
6.1 Operating and maintenance notices ...............................................38
6.2 Battery.............................................................................................38
6.2.1 Battery indicator..............................................................................38

Table of contents
B-H88.0.2X.DKZ-1.0 25 / 44
6.2.2 Changing battery.............................................................................38
7 Error and system messages ....................................................... 39
8 Technical data .............................................................................. 40
9 Service........................................................................................... 44
9.1 Manufacturer...................................................................................44

1 | About this documentation G 1107 / G 1113
26 / 44 B-H88.0.2X.DKZ-1.0
1 About this documentation
1.1 Purpose of the document
_
– This document is intended as a quick reference option.
– It does not replace the operating manual.
– For this reason, read the operating manual before operating the product for the
first time.
1.2 Legal notices
This document is entrusted to the recipient for personal use only. Any impermissible
transfer, duplication, translation into other languages or excerpts from this operating
manual are prohibited.
The manufacturer assumes no liability for print errors.
1.3 Further information
_
Software version of the product:
– V1.1 or later
_
Link to the complete operating manual:
_
http://www.greisinger.de
For the exact product name, refer to the type plate on the rear side of the product.

G 1107 / G 1113 Safety | 2
B-H88.0.2X.DKZ-1.0 27 / 44
2 Safety
2.1 Explanation of safety symbols
_
DANGER
This symbol warns of imminent danger, which can result in death, severe bodily in-
jury, or severe property damage in case of non-observance.
_
CAUTION
This symbol warns of potential dangers or harmful situations, which can cause dam-
age to the device or to the environment in case of non-observance.
_
NOTE
This symbol indicates processes, which can have a direct influence on operation or
can trigger an unforeseen reaction in case of non-observance.
2.2 Foreseeable misuse
_
The fault-free function and operational safety of the product can only be guaranteed
if applicable safety precautions and the device-specific safety instructions for this
document are observed.
If these notices are disregarded, personal injury or death, as well as property dam-
age can occur.
_
DANGER
Incorrect area of application!
In order to prevent erratic behaviour of the product, personal injury and property
damage, the product must be used exclusively as described in the chapter Descrip-
tion in the operating manual.
– The product is not suitable for use in explosion-prone areas!
– The product must not be used for diagnostic or other medical purposes on pa-
tients!
– For measurements requiring devices that are subject to authorisation or special
approvals, this product is not a substitute for such products and can only be
used as an aid in preparatory or comparison measurements!

2 | Safety G 1107 / G 1113
28 / 44 B-H88.0.2X.DKZ-1.0
2.3 Safety instructions
_
NOTE
This product does not belong in children's hands!
2.4 Intended use
_
_
_
The device is designed as a manometer and measures even the smallest pressure
differential pressures of up to ±200 hPa with a maximum resolution of up to 0.1 Pa
in air or in non-corrosive/non-ionising gases between the two pressure connections.
G 1107 G 1113
Differential pressure ±200 hPa ±2000 hPa
Max. resolution 0.1 Pa 1 Pa
Usual applications include precise measurements of filter condition, gas flow pres-
sure, draught, leak integrity, dynamic pressure flow speed.
The pressure connection is made at the supplied interchangeable pressure connec-
tion ports with suitable hoses - 4 different connection options are available as stand-
ard, many other connection options can be used easily and reliable with G 1/8 ad-
apters.
The product must only be used under the conditions and for the purposes for which
it was designed.
It must be handled with care and used according to the technical data (do not throw,
strike, etc.). Suitable measures must be used to protect the pressure connections
and be protected from dirt and moisture.

G 1107 / G 1113 The product at a glance | 3
B-H88.0.2X.DKZ-1.0 29 / 44
3 The product at a glance
3.1 The G 1100 manometer series
LCD Display Front view
Connection variants
Top view
3.2 Display elements
_
Display
_
Battery indicator Evaluation of the battery status
_
Unit display Display of the units or Min/Max/Hold information
text
_
Main display Measurement of the current pressure or value for
min/max/hold
_
Auxiliary display Measurement of the current pressure in Min/Max/
Hold mode
_
Bar graph Trend display with the special function F,NE
3.3 Operating elements
_
On / Off button
Press briefly Switch on the product
Activate / deactivate lighting
Long press Switch off the product
Reject changes in a menu
_

3 | The product at a glance G 1107 / G 1113
30 / 44 B-H88.0.2X.DKZ-1.0
Up / Down button
Press briefly Display of the min/max value
Change value of the selected parameter
Long press Reset the min/max value of the current measure-
ment
Both simultaneously Rotate display, overhead display
_
Function key
Press briefly Freeze measurement (Hold)
Return to measurement display
Call up next parameter
Long press, 2s Start menu configuration, (ONF appears in the dis-
play
Close menu, changes are saved
Long press, 4s Depending on the selected special function: Activ-
ation of the Tare function NVLL, high-resolution
measurement F,NE or rapid measurement with
mean value AVR
3.4 Connections
Universal connection Interchangeable pressure connection via G1/8"
thread.

G 1107 / G 1113 Operation | 4
B-H88.0.2X.DKZ-1.0 31 / 44
4 Operation
4.1 Opening the configuration menu
1. Press the Function key for 2 seconds to open the Configuration menu.
2. (ONF appears in the display. Release the Function key.
_
Parameter Values Meaning
_
Display unit
UN,T
Pa(G 1107 )
HPa
mBaR
BaR(G 1113 )
PSI
mmKG
_
Activatable special functions
NVLL Tare function available
G 1107
F,NE High-resolution measurement with 0.1 Pa activat-
able
G 1113
F,NE High-resolution measurement with 1 Pa activat-
able
AVR 0:02 / AVR
0:05 / AVR 0: 10
Rapid measurement with mean value over 2 s / 5
s / 10 s activatable
_

4 | Operation G 1107 / G 1113
32 / 44 B-H88.0.2X.DKZ-1.0
Measuring rate
RATE Selection of the measurement speed
SLO Slow
FAST Fast
_
Resolution
RANG Selection display resolution
AVTO Automatic switchover
_
G 1107
K, Adjusted to the highest value, e.g. -200.0 .. +200.0
hPa
LO Adjusted to the lowest value, e.g. -20.00 .. +20.00
hPa
G 1113
K, Adjusted to the highest value, e.g. -2000 .. +2000
hPa
LO Adjusted to the lowest value, e.g. -200.0 .. +200.0
hPa
_
Shut-off time
POFF
OFF No automatic shut-off
0:15 0:30 1:00 4:00
12:00
Automatic shut-off after a selected time in hours
and minutes, during which no buttons have been
pressed
_

G 1107 / G 1113 Operation | 4
B-H88.0.2X.DKZ-1.0 33 / 44
Backlight
L,TE
OFF Backlight deactivated
0:15 0:30 1:00 4:00 Automatic shut-off of the backlight after a selected
time in minutes and seconds, during which no but-
tons have been pressed
ON No automatic shut off of the backlight
_
Factory settings
IN,T
NO Use current configuration
YES Reset product to factory settings. IN,T DONE ap-
pears in the display
4.2 Open the adjustment menu
For information refer to the operating manual!

5 | Measurement Basics G 1107 / G 1113
34 / 44 B-H88.0.2X.DKZ-1.0
5 Measurement Basics
5.1 Special functions
_
With the special functions that can be selected via the Configuration menu, the
device can be optimised for special measuring tasks. After it is switched on, the
device starts up in standard measuring mode, the relevant special function is started
by pressing and holding the Function key for 4 s.
_
CAUTION
Air pressure at port variant UT!
With higher pressures greater than 1 bar, the hoses must be secured to prevent un-
intended loosening. Suitable GDZ hose clamps are used for this purpose.
– 6x1 mm PVC GDZ-01. Up to 5 bar rel., vacuum-suitable!
– 6x1 mm PE GDZ-02. Up to 10 bar rel., vacuum-suitable!
– 6x1 mm PUR GDZ-03. Up to 9 bar rel., vacuum-suitable!

G 1107 / G 1113 Measurement Basics | 5
B-H88.0.2X.DKZ-1.0 35 / 44
5.1.1 NVLL Tare function
The special function FVNC NVLL has been selected in the configuration menu.
The display can be zeroed by pressing the Function key for 4 s. If the tare function is
activated, NVLL blinks in the lower display. The tare function can be reset by pressing
the Function key again for 4 s.
NOTE
The tare function is independent of the zero point correction accessible via the set-
tings menu.
5.1.2 F,NE High-resolution measurement with 0.1 Pa (G 1107)
High-resolution measurement for the finest adjustment work, 4 Pascal Test (test of
chimney draft with living-space-independent single combustion) and many other
finely-adjusted pressure applications.
In the Configuration menu, the special function FVNC F,NE has been selected.
The high-resolution measurement can be activated by pressing and holding the
Function key for 4 s. Then the sensor is immediately zeroed and the optimised para-
meters for this measurement are activated.
CAUTION
When starting the special function, make sure that there is no pressure at the con-
nections.
NOTE
The increased current consumption in this mode decreases battery life.
The quickly determined measurement replaces other devices, such as a U-tube
manometer. The four bars in the lower display provide additional support.
– The two middle bars appear: Measurement is stable
– Left bars appear: the measurement decreases
– Right bars appear: the measurement increases
_
By pressing and holding the Function key for 2 s., the special function can be activ-
ated. END FVNC appears in the display.

5 | Measurement Basics G 1107 / G 1113
36 / 44 B-H88.0.2X.DKZ-1.0
5.1.3 F,NE High-resolution measurement with 1 Pa (G 1113)
High-resolution measurement for the finest adjustment work and many other applic-
ations with the finest adjustment of pressure.
In the Configuration menu, the special function FVNC F,NE has been selected.
The high-resolution measurement can be activated by pressing and holding the
Function key for 4 s. Then the sensor is immediately zeroed and the optimised para-
meters for this measurement are activated.
CAUTION
When starting the special function, make sure that there is no pressure at the con-
nections.
NOTE
The increased current consumption in this mode decreases battery life.
The quickly determined measurement replaces other devices, such as a U-tube
manometer. The four bars in the lower display provide additional support.
– The two middle bars appear: Measurement is stable
– Left bars appear: the measurement decreases
– Right bars appear: the measurement increases
_
By pressing and holding the Function key for 2 s., the special function can be activ-
ated. END FVNC appears in the display.
5.1.4 AVR 0:02 / AVR 0:05 / AVR 0: 10
Fast measurement with mean value over 2 s / 5 s / 10 s
Mean value mode for measurement of heavily fluctuating pressures.
In the Configuration mode, a special function AVR 0:02, AVR 0:05 or AVR 0: 10 has
been selected.
By pressing and holding the Function key for 4 s. the measurement with mean value
can be activated.
_

G 1107 / G 1113 Measurement Basics | 5
B-H88.0.2X.DKZ-1.0 37 / 44
Heavily fluctuating values arise particularly with dynamic pressure/compression
measurements in chimney draft tests of forced-air burners and, consequently, con-
ventional electronic manometers are not adequate for task. This special function op-
timises the device for this application purpose.
The different mean value times of 2, 5 or 10 seconds can be selected depending on
the requirement.
_
The first parameter is shown in the auxiliary display.
_
By pressing and holding the Function key for 2 s., the special function can be activ-
ated. END FVNC appears in the display.
_
If the Tare function is activated when called up, this special function AVR can be re-
set by pressing and holding the Function key for 4 s. In order to reactivate the Tare,
the special function must be switched in the configuration menu.

6 | Measurement Basics G 1107 / G 1113
38 / 44 B-H88.0.2X.DKZ-1.0
6 Operation and maintenance
6.1 Operating and maintenance notices
_
NOTE
Pressure connections must be protected from soiling.
6.2 Battery
6.2.1 Battery indicator
_
For additional information, refer to the operating manual!
6.2.2 Changing battery
_
A
B
C
D
Only use new, high-quality and suitable alkaline batteries!
For additional information, refer to the operating manual!

G 1107 / G 1113 Error and system messages | 7
B-H88.0.2X.DKZ-1.0 39 / 44
7 Error and system messages
Display Meaning Possible causes Remedy
---- Calculation not pos-
sible
Measurement data
acquisition is run-
ning
Waiting for data collection
No display,
unclear
characters
or no re-
sponse
when but-
tons are
pressed
Battery depleted
System error
Product is defective
Battery depleted
Error in the product
Product is defective
Replace battery
Send in for repair
BAT Battery depleted Battery depleted Replace battery
BAT LO Battery depleted Battery depleted Replace battery
ERR.1 Measuring range
exceeded
Measurement too
high
Product is defective
Stay within allowable
measurement range
Send in for repair
ERR.2 Measuring range is
undercut
Measurement too
low
Product is defective
Stay within allowable
measurement range
Send in for repair
ERR.3 Display range has
been exceeded
Incorrect display
unit
Incorrect resolution
F,NE Function active
Correct setting
Deactivate function
ERR.4 Display range has
been undercut
Incorrect display
unit
Incorrect resolution
F,NE Function active
Correct setting
Deactivate function
SYS ERR System error Error in the product Switch product on/off
Replace batteries
Send in for repair

8 | Technical data G 1107 / G 1113
40 / 44 B-H88.0.2X.DKZ-1.0
8 Technical data
_
_
G 1107
Measuring range Measuring range (Hi) Measuring range (Lo)
-200.0 .. +200.0 hPa
(mbar)
-2.900 .. +2.900 PSI
-150.0 .. +150.0 mmHg
(Torr)
-2000 .. +2000 Pa
-20.00 .. +20.00 hPa
(mbar)
-20.00 .. +20.00 mmHg
(Torr)
Accuracy ± 0,1 % FSS typical (at nominal temperature 25
°C)
± 1 % FSS max.
Overload Max. ± 1700 hPa
Pressure connection 2 hose connections, interchangeable with G1/8
universal ports
Measuring cycle FAST: approx. 25 measurements per second
SLO: approx. 2.5 measurements per second
Display 3-line segment LCD, additional symbols, illumin-
ated (white, duration adjustable)
Standard function Min/Max/Hold
Auto-power-Off function / if activated, the product
switches off automatically
Activatable special functions NVLL: Tare function
F,NE: With 0.1 Pa resolution
AVR: Averaging over 2 s / 5 s / 10 s
Adjustment Zero point and gradient adjustment
Housing Break-proof ABS housing
Protection rating IP67 (pressure connections must be protected
from soiling and moisture)
Dimensions
L*W*H [mm] and
weight
108 * 54 * 28 mm without pressure connection
150 g incl. battery

G 1107 / G 1113 Technical data | 8
B-H88.0.2X.DKZ-1.0 41 / 44
Operating conditions -20 to +50 °C; 0 to 95 % r.h. (temporarily 100 %
r.h.)
Storage temperature -20 to +70 °C
Current
supply
2*AA battery (included in the scope of delivery)
Current consump-
tion/
Battery life
approx. 1 mA (slow measurement SLO)
Operating time approx. 3000 h
Battery indicator 4-stage battery status indicator,
Note for low battery voltage: "BAT LO"
Directives and standards The devices conform to the following Directives of
the Council for the harmonisation of legal regula-
tions of the Member States:
2014/30/EU EMC Directive
2011/65/EU RoHS
Applied harmonised standards:
EN 61326-1:2013 Emission limits: Class B
Immunity according to Table 2
Additional error: < 1 % FS
EN 50581:2012
The device is intended for mobile use and/or sta-
tionary operation in the scope of the specified op-
erating conditions without further limitations.
_
_

8 | Technical data G 1107 / G 1113
42 / 44 B-H88.0.2X.DKZ-1.0
G 1113
Measuring range Measuring range (Hi) Measuring range (Lo)
-2000 .. +2000 hPa
(mbar)
-2.000 .. +2.000 bar
-29.00 .. +29.00 PSI
-1500 .. +1500 mmHg
(Torr)
-200.0 .. +200.0 hPa
(mbar)
-200.0 .. +200.0 mmHg
(Torr)
Accuracy ± 0,1 % FSS typical (at nominal temperature 25
°C)
± 1 % FSS max.
Overload Max. ± 3100 hPa
Pressure connection 2 hose connections, interchangeable with G1/8
universal ports
Measuring cycle FAST: approx. 25 measurements per second
SLO: approx. 2.5 measurements per second
Display 3-line segment LCD, additional symbols, illumin-
ated (adjustable white, permanent illumination)
Standard function Min/Max/Hold
Auto-power-Off function / if activated, switches
the product off automatically
Activatable special functions NVLL: Tare function
F,NE: With 1 Pa resolution
AVR: Averaging over 2 s / 5 s / 10 s
Calibration Zero point and gradient adjustment
Housing Break-proof ABS housing
Protection rating IP67 (pressure connections must be protected
from soiling and moisture)
Dimensions
L*W*H [mm] and
weight
108 * 54 * 28 mm without pressure connection
150 g incl. battery
Operating conditions -20 to +50 °C; 0 to 95 % r.h. (temporarily 100 %
r.h.)