Grizzly H8126 Quick start guide

-24- H8126 Wide Wheel Ginder

















































 









Parts Breakdown

H8126 Wide Wheel Grinder -25-
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PS06 PHLP HD SCR 10-24 X 3/8 30 PH8126030 GRAY GRINDING WHEEL #36
2 PH8126002 WIRE NUT 31 PH8126031 WHITE GRINDING WHEEL #100
3 PW02M FLAT WASHER 5MM 32 PH8126032 WHEEL FLANGE
4 PH8126004 ARROW LABEL 33 PH8126033 RUBBER FOOT
5 PS24 PHLP HD SCR 8-32 X 3/8 34 PH8126034 BOTTOM PLATE
6 PN14 HEX NUT 8-32 35 PH8126035 STRAIN RELIEF
7 PW05M FLAT WASHER 4MM 36 PH8126036 110V POWER CORD
8 PW06 FLAT WASHER 1/4 37 PH8126037 WIRE NUT
9 PB51 HEX BOLT 1/4-20 X 3/8 38 PH8126038 SWITCH PLATE
10 PH8126010 LEFT SPARK GUARD 39 PH8126039 ROCKER SWITCH SW-155-BB2
11 PH8126011 RIGHT SPARK GUARD 40 PH8126040 CAPACITOR RETAINER
12 PH8126012 BRACKET 41 PH8126041 CAPACITOR 6MFD 250VAC
13 PH8126013 NUT PLATE 42 PN07 HEX NUT 10-24
14 PH8126014 EYE SHIELD 43 PH8126043 PHLP HD SCR 10-24 X 4-1/4
15 PH8126015 LEFT TOOL REST 44 PW06 FLAT WASHER 1/4
16 PH8126016 RIGHT TOOL REST 45 PLW02 LOCK WASHER 1/4
17 PB15 HEX BOLT 5/16-18 X 3/8 46 PN05 HEX NUT 1/4-20
18 PW07 FLAT WASHER 5/16 47 PSS06 SET SCREW 1/4-20 X 3/4
19 PLW01M LOCK WASHER 5MM 48 PH8126048 STRAIN RELIEF
20 PH8126020 COPPER WASHER 5MM 49 PH8126049 BASE
21 PH8126021 SPECIAL TOOTH SCR 1/4-20 X 3/8 50 PH8126050 END COVER
22 PH8126022 SPECIAL TOOTH SCR 10-24 X 1/4 51 PH8126051 MOTOR CASE
23 PS18 PHLP HD SCR 10-24 X 1/4 52 P6202 BALL BEARING 6202ZZ
24 PH8126024 RIGHT 1/2" ARBOR NUT 55 PH8126055 FAN
25 PH8126025 LEFT 1/2" ARBOR NUT 56 PH8126056 STATOR
26 PH8126026 RIGHT OUTER WHEEL GUARD 57 PH8126057 DATA/WARNING LABEL
27 PH8126027 LEFT OUTER WHEEL GUARD 58 PH8126058 ROTOR AND SHAFT
28 PH8126028 RIGHT INNER WHEEL GUARD *59 PPAINT-1 PAINT-GRIZZLY GREEN
29 PH8126029 LEFT INNER WHEEL GUARD
Parts List
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REPLACE that label before using the machine again. Contact
Grizzly at [phone] or www.grizzly.com to order new labels.
*Not shown on parts diagram.