Grizzly H0584 User manual

Product Information
• 6,000 RPM
• Requires 90 PSI
• Requires 12 CFM
• Requires 5" hook and loop sanding disc
• 1/4" NPT air inlet
• Weighs 4 lbs.
Inventory
A. Air Sander ....................................................1
B. Plastic Hose .................................................1
C. Dust Collection Bag ......................................1
D. Wrench .........................................................1
MODEL H0584
DUAL ACTION SANDER
INSTRUCTION SHEET
EYE INJURY HAZARD!
Always wear safety glasses
when using this tool to
prevent serious personal
injury.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service.
DUST HAZARD!
Always wear respirator when
using this tool. Figure 1. Model H0584 inventory.
Assembly
To assemble the Model H0584:
1. Install a 1⁄4" NPT male quick-connect fitting
(not included) into the sander hose.
2. Attach a 5" hook and loop sanding disc to the
sanding pad as shown in Figure 2.
A
BC
D
Figure 2. Attaching sanding disc.
COPYRIGHT © JUNE, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8321 PRINTED IN TAIWAN
DO NOT EXCEED 120 PSI!
Personal injury could
occur.

Throttle
Lever
Maintenance
Lubricate at the beginning of the sanding task.
Place one or two drops of pneumatic tool oil
directly into the air fitting as shown in Figure 5.
Figure 5. Lubricating directly into air fitting.
Operation
To operate the sander:
1. Plug the tool into compressed air.
2. Hold the sander and press the throttle lever
(Figure 4) to operate the sander.
A filter/lubricator/regulator set up is not recom-
mended, as excess oil in the tool could spray onto
the workpiece.
Before installing the sanding disc, run the sander
for a few minutes to eject excess oil, then wipe the
tool down with a rag and begin sanding. Oil the
tool after use or storage.
Service
To replace the sanding pad:
1. Slide the included wrench between the sand-
er and the sanding pad and insert it onto the
spindle as shown in Figure 6.
3. Turn the regulator knob (Figure 4) to adjust
the speed of the sanding disc.
4. Remove pressure on the throttle lever to stop
the sander.
5. When the sandpaper loses its effectiveness,
disconnect the tool, remove sandpaper
from the pad, and replace with a new disc.
Figure 4. Sander controls.
Figure 6. Wrench inserted onto spindle.
2. Hold the wrench and rotate the pad counter-
clockwise to remove it.
3. Install a new sanding pad (Part PH0584040)
and secure it with the wrench.
If you need help with your new pneumatic tool,
call our Tech Support at: [phone].
Wrench
Sanding
Pad
3. Attach the plastic hose to the sander as
shown in Figure 3A, insert the plastic hose
into the dust collection bag, and secure with
the strings (Figure 3B).
Figure 3. Attaching plastic hose to sander and
dust collection bag.
BA
Regulator
Knob

H0584 Parts Breakdown and List









 






  


 







 






REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH0584001 THROTTLE LEVER 22 PH0584022 CYLINDER PIN
2 PRP73M ROLL PIN 4 X 30 23 PH0584023 CYLINDER O-RING
3 PH0584003 VALVE PIN 24 PH0584024 CYLINDER
4 PH0584004 VALVE BODY 25 PH0584025 CYLINDER PIN
5 PH0584005 O-RING 26 PH0584026 REAR PLATE
6 PH0584006 THROTTLE VALVE 27 P6200 BALL BEARING 6200ZZ
7 PH0584007 VALVE SPRING 28 PH0584028 MOTOR GASKET
8 PH0584008 MOTOR HOUSING 29 PH0584029 PAD COVER
9 PR36M EXT RETAINING RING 7MM 30 PSB23M CAP SCREW M4-.7 X 12
10 PH0584010 O-RING 31 PH0584031 COTTON RING
11 PH0584011 REGULATOR 32 PH0584032 CRANK SHAFT
14 PH0584014 AIR ADAPTOR 33 PH0584033 KEY
14-1 PH0584014-1 PLASTIC HOSE 34 PH0584034 SCREW
14-2 PH0584014-2 DUST BAG 35 PH0584035 LOWER WEIGHT
15 PSB50M CAP SCREW M5-.8 X 10 36 P6202 BALL BEARING 6202ZZ
17 P6200 BALL BEARING 6200ZZ 37 PH0584037 SPECIAL WRENCH
18 PH0584018 FRONT PLATE 38 PH0584038 RANDOM SHAFT
19 PH0584019 ROTOR 39 PR29M INT RETAINING RING 32MM
20 PH0584020 VANE SPRING 40 PH0584040 SANDING PAD
21 PH0584021 VANE