Grohe Electronic 15180XX1 User manual

Electronic
15181XX1
Electronic
15180XX1
Installation Instructions / Warranty

2
Hansgrohe Electronic Lavatory Faucet with Temperature Control
15180XX1
Hansgrohe Electronic Lavatory Faucet
15181XX1
16
Caution: do not bend or twist the supply
hoses!
Technical data
Max. water pressure: 116 psi
Recommended pressure: 14.5 - 72 psi
Hot water temperature: max. 158 °F*
Recommended hot water temperature: 120°F - 140°F*
Rate of flow:
1.5 gpm @ 44 psi
Automatic shutoff: after 35 seconds
Hole size in mounting surface: 1 3/8“
Max. mounting surface thickness 1 1/8“
Requires standard 110V electrical outlet.**
*please know and follow all applicable local plumbing codes when
setting the temperature on the water heater. In Massachusetts, the
water heater may be set no higher than 112oF.
**please know and follow all applicable local codes regarding
placement and type of outlet.

3
Installation
Flush the hot and cold supplies thoroughly before
installing this faucet.
Place the faucet in the hole in the mounting surface
(1).
From beneath the sink, install the fiber washer, metal
washer and mounting nut (2).
Install the adapters on the stops (3).
Install the filters (4) and supply lines (5).
Connect the transformer. Plug into the outlet.
Use a cable tie to bundle excess cable.

4
Turn the water on to the faucet (1).
Peel the protective film from the sensor (2).
Wait 15 seconds, then put a hand in front of the sensor.
The water should turn on automatically.
Model 15180 only: Pivot the temperature control
lever forward to make the water cooler.
Model 15181 only: Turn the water off at the stops (1).
Remove the set screw on the back of the faucet (2).

5
Pull the faucet housing off (1).
Use a screwdriver to set the water temperature (2). Turn
the screw to the rear to make the water warmer, to the
front to make it cooler.
Replace the faucet housing. Tighten the set screw.
Cleaning: Block the sensor for 5 seconds (1).
This will turn the water off for approximately 75 seconds
so that the sink may be cleaned (2).

6
Faucet Maintenance
Reset the faucet: Remove the set screw with a 2.5 mm
Allen wrench.
Block the sensor for 2 seconds.
Wait 10 seconds (1), then replace the set screw (2).

7
Wait 15 seconds (3), then place a hand in front of the
sensor (4). The water should turn on.
Cleaning the filters and aerator
If the flow of water is reduced, the filters and/or the aera-
tor must be cleaned.
To clean the aerator: Block the sensor for 5 seconds
to temporarily shut off the water (1).
Unscrew and remove the aerator. Flush any debris from
the aerator at another faucet (2).

8
To clean the filters: Turn the water off at the stops (1).
Disconnect the supply hoses from the adapters (2). Pull
the filters out and clean them.

9
Replacement Parts
1 aerator 96788XXX
2 solenoid valve 98854000
3 fixation set 97812000
4 connection hose 96405000
5 back flow preventor cartridge 96906000
6 electronics 96905000
7 AC adapter 97690000
8 transformer 97689001
1
2
3
4
5
6
7
8

10
Cleaning Recommendation for Hansgrohe Products
Modern faucetry and shower products utilize a combination of materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper
treatment is not covered under the Hansgrohe warranty.
Cleaning Materials for Faucets and Showers
•To remove lime scale, use only products made specifically for that purpose. Always follow the
manufacturer’s instructions when using.
•Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will
cause considerable damage to finishes and to plastic components.
•Never mix cleaning materials.
•Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges.
Cleaning Procedures
•Clean your faucets and shower products as and when required. Regular cleaning will prevent
scale buildup and water spotting.
•Follow the label instructions. Do not allow any cleaner to remain on the product for longer than
necessary.
•When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the
product.
•After cleaning, rinse thoroughly with clear water to remove any cleaner residue.
Important
•Soap and shampoo residue can also cause damage to the product. Rinse well with clean water
after use.
•If the surface is already damaged, harsh cleaning materials will cause further damage.