Grotime Rollover User manual

ROLLOVER
5in 1cot to full size single bed
Two adults required to assemble this cot.
!
Themanufacturer's assembly instructions must be followed
in detail to ensure the safety features to thecotare not compromised.
!
This product is covered by a number of registered designs, trademarks and patents pending

2xEnd Panels
PB
1 x Fixed Side
PA
1 x Drop Side
PC
1 x Cot Base
PD
x2
Allen Key
HG
x8
Feet Pads
HH
x4
CAMDOCK
TM
Base Plates
HF
x12x32
16mm Bolts
HA
70mmBolts
HB
x4
Guide Pins
HC
x4
Wood Screws
HD
HARDWAREINVENTORY
PRE-INSTALLEDHARDWARE
PARTS LIST
4 x BILATERAIL
TM Base Rails
PE
11 x Single Bed Slats
PF
2xBILATERAIL
TM Base Bracketss
PG
2
Oval Badges x 4 pcs with
40mm Bolts x 8 pcs
Locking Bolts

STEP1
ASSEMBLEFIXED SIDE TOENDS
STEP2
FIX FOUR CAMDOCK TM BASE PLATES*
*Patent pending
HIGH
Bassinetlevel
LOW
Toddler level
Chose high or low
positionfor mattressbase
!
3
x4
70mmBolts
HB
FixedSide
PA
EndPanels
PB
x1 x2
Do not tighten bolts at this stage
!
x8
16mmBolts
HA
x4
CAMDOCK Base Plates
HF
Do not tighten bolts at this stage
!
TM

STEP 3
PLUG FINGER ENTRAPMENTS
STEP 4
PLACE COT BASE ON TOP OF BASE PLATES
4
x8
16mm Bolts
HA
1 x Cot Base
PD

STEP 5
ASSEMBLE COT BASE
STEP 6
SCREW FOUR GUIDE PINS INTO ENDS FIRMLY
5
x8
16mm Bolts
HA
x4
Guide Pins
HC
Screw Driver
Do not tighten bolts at this stage
!

STEP 7
ASSEMBLE DROP SIDE
Ensure correct side is facing out.
Align two access holes in the built-in
runner with the guide pins on one end.
Now repeat on other end.
!
STEP 8
FULLY SCREW IN LOCKING BOLTS
Lift drop side up until it clicks
into the locking position.
b.
a.
6
x1
Drop Side
PC

STEP 9
TIGHTEN ALL BOLTS
STEP 10
OPERATION
Base shown in Lower Position.
1.
2.
3.
To lower drop side, lift from centre of top rail, hold side in that position while using your leg to push inward on
centre of bottom rail. Then allow to slide gently down.
7

Remove dropside by reversing to step 5.
Day Bed
DAY BED CONVERSION
COT BED CONVERSION
Remove dropside by reversing to step 5.
a.
b.
8
Cot Bed
Remove dropside guide pins (HC) from the ends to prevent injury.
!

FULL SIZE SINGLE BED CONVERSION
STEP 1 Disassemble the cot following the
assemble instructions in reverse order.
Roll over cot ends on their sides
b.
a.
STEP 2
REMOVE FOUR GROTIME BADGES
9
Rollover action Patent Pending

10
STEP4
ASSEMBLE SINGLE BED BASE
Layone siderail down thenslotallslats intothe mortises.
Place the second side rail on top.
Working from one end slot all stats into the mortises.
STEP3
ASSEMBLE BILATERAIL
TM BED RAILS
Patent pending
Use the four wood screws to
r.
x2 x11
Assembled base rails
PE
Cot Bed Slats
PF
x4
WoodScrews
HD
Screw Driver
1.
2.
3.
Ensure the slat withthe warning labels is correctlypositioned
in the middleand the “this waydown” lable
is facingdown as directed by the
warning lableon therails.
!
x4 x2
BILATERAIL
TM Base Brackets
PG
BILATERAIL
TM BaseRails
PE
x8
mm Bolts
HE
20mm Insert Nut
HP
Align insert
sleeve so the slot
is facing out
Place insert sleeves
into base rail.
(2 at each end of rail)
x8
16