Grundfos UNILIFT AP35B User manual

6
Original installation and operating instructions.
CONTENTS Page
1. General description 6
1.1 Applications 6
1.2 Storage and operating conditions 7
1.3 Sound pressure level 7
2. Safety 7
3. Electrical connection 7
3.1 Checking of direction of rotation 8
4. Installation 8
4.1 Connection 8
4.2 Pump location 9
4.3 Installation on auto-coupling 9
4.4 Free-standing installation 10
4.5 Setting of level switch 10
5. Start-up 10
6. Maintenance and service 10
6.1 Oil 10
6.2 Pump construction 11
6.3 Service kits 11
6.4 Contaminated pumps 11
7. Fault finding chart 12
8. Disposal 12
1. General description
Fig. 1 Unilift AP35B, AP50B
1.1 Applications
The Grundfos Unilift AP35B and AP50B pumps are
single-stage submersible pumps designed for the
pumping of waste water.
The pump is capable of pumping water which con-
tains a limited quantity of solids, however not stones
and similar materials, without being blocked or dam-
aged.
The pump is available for automatic as well as man-
ual operation and can be installed in a permanent
installation (on auto-coupling or as a free-standing
pump) or used as a portable pump.
Prior to installation, read these installation
and operating instructions. Installation and
operation must comply with local regula-
tions and accepted codes of good prac-
tice.
Warning
The use of this product requires
experience with and knowledge of the
product.
Persons with reduced physical, sensory or
mental capabilities must not use this
product, unless they are under
supervision or have been instructed in the
use of the product by a person responsible
for their safety.
Children must not use or play with this
product.
TM03 4189 1806
Handle
with clamp
Discharge
port
Pump inlet
Level
switch

7
The pump is suitable for:
Incorrect application of the pump (e.g. resulting in
blocking of the pump) and wear are not covered by
the warranty.
1.2 Storage and operating conditions
1.3 Sound pressure level
The sound pressure level of the pump is lower than
the limiting values stated in the EC Council Directive
2006/42/EC relating to machinery.
2. Safety
3. Electrical connection
Note: Depending on local regulations, a pump with
10 metres of mains cable must be used if the pump
is used as a portable pump for different applications.
The electrical connection should be carried out in
accordance with local regulations.
The operating voltage and frequency are marked on
the pump nameplate. Please make sure that the
motor is suitable for the electricity supply on which it
will be used.
Three-phase pumps must be connected to an exter-
nal motor starter with differential release. The nomi-
nal current of the motor starter must correspond to
the electrical data marked on the pump nameplate.
If a level switch is connected to a three-phase pump,
the motor starter must be magnetically operated.
Single-phase pumps incorporate thermal overload
protection and require no additional motor protec-
tion.
Note: If the motor is overloaded, it will stop automat-
ically. When it has cooled to normal temperature, it
will restart automatically.
Applications Unilift
AP35B Unilift AP50B
Groundwater lowering zz
Pumping in drainage pits zz
Pumping in surface water pits
with inflow from roof gutters,
shafts, tunnels, etc. zz
Emptying of ponds, tanks, etc. zz
Pumping of fibre-containing
waste water from laundries
and industries zz
Pumping of domestic waste
water from septic tanks and
sludge treating systems zz
Pumping of domestic waste
water without discharge from
water closets zz
Pumping of domestic waste
water with discharge from wa-
ter closets z
Maximum particle size [mm] 35 50
The pump must not be used in or at swim-
ming pools, garden ponds, etc. when there
are persons in the water.
Storage temperature: Down to –30 °C.
Minimum liquid
temperature: 0 °C.
Maximum liquid
temperature: +40 °C.
Installation depth: Maximum 7 metres below
liquid level.
pH value: Between 4 and 10.
Density: Maximum 1100 kg/m³.
Viscosity: Maximum 10 mm²/s.
Technical data: See pump nameplate.
Pump installation in wells must be carried
out by specially trained persons.
As a precaution, the pump must be con-
nected to a socket with earth connection.
The installation must be fitted with an
earth leakage circuit breaker (ELCB) with
a tripping current < 30 mA.
The pump must be connected to an exter-
nal mains switch with a minimum contact
gap of 3 mm in all poles. If the pump is not
installed close to the switch, this must be
of a lockable type.

8
3.1 Checking of direction of rotation
(Three-phase pumps only)
The direction of rotation should be checked every
time the pump is connected to a new installation.
Check the direction of rotation as follows:
1. Position the pump so that the impeller can be
observed.
2. Start the pump for a short period.
3. Observe the rotation of the impeller. The correct
direction of rotation is indicated by an arrow on
the top of the motor (clockwise when seen from
the bottom). If the impeller rotates in the wrong
direction, reverse the direction of rotation by
interchanging two of the phases to the motor.
If the pump is connected to a piping system, the
direction of rotation can be checked as follows:
1. Start the pump and check the quantity of water or
the discharge pressure.
2. Stop the pump and interchange two of the
phases to the motor.
3. Start the pump and check the quantity of water or
the discharge pressure.
4. Stop the pump.
5. Compare the results taken under points 1 and 3.
The connection which gives the larger quantity of
water or the higher pressure is the correct direc-
tion of rotation.
4. Installation
4.1 Connection
For permanent installation, it is recommended to fit a
union, a non-return valve and an isolating valve in
the discharge pipe.
If the pump is installed in a pit with a minimum free
cable length of 100 mm, see fig. 5, the minimum pit
dimensions must be as shown in fig. 2.
Furthermore, the pit should be dimensioned accord-
ing to the relation between the water flow to the pit
and the pump performance.
Fig. 2 Minimum pit dimensions in pit if minimum
free cable length is 100 mm
The installation of the pump must be car-
ried out by specially trained persons.
Care must be taken to ensure that persons
cannot come into contact with the pump
impeller.
TM03 4190 1806
550 mm
600 mm

9
4.2 Pump location
The pump can be used in vertical or horizontal posi-
tion, see fig. 3.
During continuous operation, the motor and the
pump inlet must always be completely covered by
the pumped liquid.
Fig. 3 Position of pump
When the pipe/hose has been connected, place the
pump in its operating position.
Note: Do not lift or lower the pump by means of the
electric cable.
Position the pump so that the pump inlet will not be
blocked or partly blocked by sludge, mud or similar
materials.
It is recommended to place the pump on a solid
base, see fig. 4.
Fig. 4 Place pump on a solid base
In the case of permanent installation, the pit must be
cleared of sludge, pebbles, etc. before the pump is
installed.
4.3 Installation on auto-coupling
See figs. A and B, pages 182 and 183.
Pumps for permanent installation can be installed on
a stationary auto-coupling and operated completely
or partially submerged in the pumped liquid.
1. Drill mounting holes for guide rail bracket on the
inside of the pit and fasten the guide rail bracket
provisionally with two screws.
2. Place the auto-coupling base unit on the bottom
of the pit. Use a plumb line to establish the cor-
rect positioning. Fasten with heavy-duty expan-
sion bolts. If the bottom of the pit is uneven, the
auto-coupling base unit must be supported so
that it is level when being fastened.
3. Assemble the discharge line in accordance with
the generally accepted procedures and without
exposing the line to distortion or tension.
4. Knock the guide rails on to the spigots of the bot-
tom part of the auto-coupling. Bevel the inside of
the guide rails to facilitate installation. The guide
rails must fit tightly on the spigots. We
recommend ¾" medium size pipes as guide rails.
5. Adapt the length of the guide rails to fit precisely
the bracket at the top.
6. Unscrew the provisionally fastened guide rail
bracket, fit it on top of the guide rails and finally
fasten it firmly to the pit wall.
Note: The guide rails must not have any axial play
as this would cause noise during pump operation.
7. Clean out debris from the pit before lowering the
pump into the pit.
8. Fit the auto-coupling half on to the discharge port
of the pump. Then slide the guide bar of this cou-
pling half between the guide rails and lower the
pump into the pit by means of a chain. When the
pump reaches the auto-coupling base unit, the
pump will automatically connect tightly.
9. Hang up the end of the chain on a suitable hook
at the top of the pit.
10.Adjust the length of the motor cable by coiling it
up on a relief fitting, so the cable is not damaged
during operation. Fasten the relief fitting to a suit-
able bracket at the top of the pit. Make sure that
the cables are not sharply bent or pinched.
Note: The end of the cable must not be submerged,
as water may penetrate through the cable into the
motor.
TM03 4191 1806TM01 3597 4998
•
•
•
•
•
•••
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
••••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
••
••
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
••
•
•
•
•
•••••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•••
•
•
•
•
••••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
••
••
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
••
•
•
•
••
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
••
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
••
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

10
4.4 Free-standing installation
See fig. C, page 184.
For free-standing installation of the pumps, fit a 90°
elbow to the discharge port. The pump can be
installed with a hose or rigid pipe and valves.
In order to facilitate service of the pump, fit a flexible
union or coupling to the discharge line for easy sepa-
ration.
If a hose is used, make sure that the hose does not
buckle and that the inside diameter of the hose
matches that of the discharge port.
If a rigid pipe is used, the union or coupling, non-
return valve and isolating valve should be fitted in
the sequence mentioned, as seen from the pump
side.
Lower the pump into the liquid.
If the pump is installed in muddy conditions or on
uneven ground, it is recommended to support the
pump on bricks.
4.5 Setting of level switch
Intermittent operation:
For pumps supplied with a level switch, the differ-
ence in level between start and stop can be set by
adjusting the free cable between the level switch and
the pump handle.
The longer the length of free cable, the larger the dif-
ference in level between start and stop.
The pump is allowed to run for maximum 5 minutes
per 30 minutes without the motor being submerged
in the liquid.
Fig. 5 Setting of level switch
Continuous operation:
During continuous operation, the pump must always
be completely covered by the pumped liquid.
5. Start-up
Before start-up, the pump inlet must be submerged
in the pumped liquid.
Open the isolating valve, if fitted, and check the level
switch setting.
Note: The pump may be run briefly to check the
direction of rotation without being submerged in the
pumped liquid.
6. Maintenance and service
Before carrying out maintenance and service, it must
be ensured that the pump has been thoroughly
flushed with clean water. Rinse the pump parts in
water after dismantling.
Check the pump and replace the oil once a year.
If the pump is used for pumping liquids containing
abrasive particles or it is operating continuously,
the pump must be checked at shorter intervals.
6.1 Oil
The pump contains approx. 60 ml non-poisonous oil.
Used oil must be disposed of in accordance with
local regulations.
If the drained oil contains water or other impurities,
the shaft seal should be replaced.
TM03 4192 1806
270 mm
Stop
Before starting work on the pump, make
sure that the electricity supply to the pump
has been switched off and that it cannot be
accidentally switched on.
Out of consideration for the personal
safety and health, this work must be car-
ried out by specially trained persons.
Furthermore, all rules and regulations cov-
ering safety, health and environment must
be observed.
During dismantling, caution should be
exercised as there will be access to sharp
edges, etc. which may cut.
A possible replacement of the cable or the
level switch must be carried out by an
authorised Grundfos service workshop.

11
6.2 Pump construction
The construction of the pump will appear from the
table below and fig. D, page 184.
6.3 Service kits
6.4 Contaminated pumps
Note: If a pump has been used for a liquid which is
injurious to health or toxic, the pump will be classi-
fied as contaminated.
If Grundfos is requested to service the pump,
Grundfos must be contacted with details about the
pumped liquid, etc. before the pump is returned for
service. Otherwise Grundfos can refuse to accept
the pump for service.
Possible costs of returning the pump are paid by the
customer.
However, any application for service (no matter to
whom it may be made) must include details about
the pumped liquid if the pump has been used for liq-
uids which are injurious to health or toxic.
Pos. Description
50 Pump housing
37a O-ring
49 Impeller
150 Motor with flange
66 Washer
84 Base
67 Lock nut
6 Inlet part
105a Shaft seal
182 Level switch
Service kit Part number
Shaft seal, standard 96429307
Shaft seal, FKM 96429308
Oil 96010646

12
7. Fault finding chart
8. Disposal
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.
Fault Cause Remedy
1. Motor does not
start. a) No electricity supply. Connect the electricity supply.
b) Motor switched off by level switch. Adjust/replace the level switch.
c) Fuses are blown. Replace fuses.
d) Motor protection/thermal relay has
tripped out. Wait until the motor protection trips in again/reset the relay.
e) Impeller blocked by impurities. Clean the impeller.
f) Short-circuit in cable or motor. Replace the defective part.
2. Motor protection/
thermal relay trips
out after short
time of operation.
a) Temperature of pumped liquid too high. Use another pump type.
b) Impeller blocked or partly blocked by im-
purities. Clean the pump.
c) Phase failure. Call an electrician.
d) Voltage too low. Call an electrician.
e) Overload setting of the motor starter too
low. Adjust the setting.
f) Incorrect direction of rotation.
See section 3.1 Checking of direction of
rotation.
Reverse the direction of rotation.
3. Pump runs
constantly or
gives insufficient
water.
a) Pump partly blocked by impurities. Clean the pump.
b) Discharge pipe or valve partly blocked by
impurities. Clean the discharge pipe.
c) Impeller not properly fixed to the shaft. Tighten the impeller.
d) Incorrect direction of rotation.
See section 3.1 Checking of direction of
rotation.
Reverse the direction of rotation.
e) Incorrect setting of level switch. Adjust the level switch.
f) Pump too small for the application. Replace the pump.
g) Impeller worn. Replace the impeller.
4. Pump runs but
gives no water. a) Pump blocked by impurities. Clean the pump.
b) Discharge pipe or non-return valve
blocked by impurities. Clean the discharge pipe.
c) Impeller not properly fixed to the shaft. Tighten the impeller.
d) Air in pump. Vent the pump and the discharge
pipe.
e) Liquid level too low. The pump inlet is not
completely submerged in the pumped liq-
uid.
Submerge the pump in the liquid or
adjust the level switch.
f) Level switch does not move freely. Make the level switch move freely.
Subject to alterations.