Grundig Music Boy 51 RP 5201 PLL User manual

PORTABLE RADIO
Music 51 RP 5201 PLL
NL
DE
NO
EN
DA
FR
SV
IT
TR
ES
FI
RU

3
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
LIFT
AC~
ON/OFF + 5 PRESETS 1, 2, 3, 4, 5
p LIFT
SNOOZE
ALARM
MODE
SLEEP
MEM.
-/+ TUNING
AC ~
P •• P
x
e § § TONE !
+ VOL. – 0

4
________________________________________________________________________________
DEUTSCH
5 SICHERHEIT UND INFORMATIONEN
6 AUF EINEN BLICK
8 STROMVERSORGUNG
9 EINSTELLUNGEN
10 BETRIEB
ENGLISH
12 SAFETY AND INFORMATION
13 OWERVIEW
14 POWER SUPPLY
15 SETTINGS
16 OPERATION
FRANCAIS
18 INFORMATIONS RELATIVES A LA
SECURITE
19 VUE D’ENSEMBLE
21 ALIMENTATION ELECTRIQUE
22 RÉGLAGES
23 FONCTIONNEMENT
ITALIANO
25 SICUREZZA E INFORMAZIONI
26 IN BREVE
28 ALIMENTAZIONE ELETTRICA
29 IMPOSTAZIONI
30 FUNZIONAMENTO
РУССКИЙ
32 ИНФОРМАЦИЯ ПО ТЕХНИКЕ
БЕЗОПАСНОСТИ
33 ОБЗОР
35 ЭЛЕКТРОПИТАНИЕ
36 НАСТРОЙКИ
37 ЭКСПЛУАТАЦИЯ
ESPAÑOL
39 SEGURIDAD E INFORMACIÓN
40 VISTA GENERAL
42 ALIMENTACIÓN DE CORRIENTE
43 AJUSTES
44 FUNCIONAMIENTO
NEDERLANDS
46 INFORMATIE EN VEILIGHEID
47 IN EEN OOGOPSLAG
49 STROOMTOEVOER
50 INSTELLINGEN
51 GEBRUIK
NORSK
53 SIKKERHET OG INFORMASJON
54 OVERSIKT
56 STRØMFORSYNING
57 INNSTILLINGER
58 DRIFT
DANKS
60 SIKKERHED OG INFORMATION
62 KORT OVERSIGT
64 STRØMFORSYNING
65 INDSTILLINGER
66 ANVENDELSE
SVENSKA
67 SÄKERHET OCH INFORMATION
68 EN ÖVERBLICK
70 STRÖMFÖRSÖRJNING
71 INSTÄLLNINGAR
72 ANVÄNDNING
SUOMI
74 TURVALLISUUS JA TIEDOT
75 YLEISKATSAUS
77 VIRRANSYÖTTÖ
78 SÄÄDÖT
79 KÄYTTÖ
TÜRKÇE
81 GÜVENLİK
83 GENEL BAKIŞ
85 GÜÇ KAYNAĞI
86 AYARLAR
87 ÇALIŞTIRMA

ENGLISH
12
7
This device is designed for the playback of audio
signals. Any other use is expressly prohibited.
7
Make sure the device is protected from dripping or
splashing water. Do not place any vessels such as
vases on the device. These may be knocked over
and spill fluid on the electrical components, thus
presenting a safety risk.
Do not place any naked flames such as candles on
the device.
7
Ensure that the device is adequately ventilated by
placing it at least 10 cm from any other object. Do
not cover the device with newspapers, table cloths,
curtains, etc.
7
Only use the device in a moderate climate.
7
If malfunctions occur due to static electricity charges
or fast transient (burst), reset the device. To do this,
pull out the power plug and connect it again after a
few seconds.
7
When deciding where to place the device, please
note that furniture surfaces are covered by various
types of varnish and plastic, most of which contain
chemical additives. These additives can corrode the
device supports, leaving residues on the furniture sur-
faces which can be difficult or impossible to remove.
7
Do not use any cleaning agent, as this may damage
the casing. Clean the device with a clean, dry cloth.
7
Never open the device casing. The manufacturer will
not accept any liability for damage resulting from im-
proper handling.
7
Note, prolonged listening at loud volumes
with the earphones can damage your
hearing.
SAFETY AND INFORMATION______________________________
Information
This device is noise-suppressed accor-
ding to the applicable EU directives.
This product fulfils the European di-
rectives 2006/95/EC, 2009/125/
EC and 2011/65/EU.
The type plate is located on the bottom of the device.
Technical data
Power supply: 230 V, 50/60Hz
Max.
power consumption: Operation <5W,
Stand-by <1W
Output: DIN 45324,
10% THD 1W
Frequency band: FM 87.5 ...108.0 MHz
Dimensions and weight:
W x H x L 247 x 127 x 62 mm
Weight approx. 0.9 kg
Technical and design modifications reserved.
Environmental note
This product has been manufactured
with high quality parts and materials
which can be reused and are suitable
for recycling.
Therefore, do not dispose the product
with normal domestic waste at the end of its service life.
Take it to a collection point for the recycling of electri-
cal and electronic equipment. This is indicated by this
symbol on the product, in the operating manual and on
the packaging.
Please consult your local authorities to learn the nearest
collection point.
Help protect the environment by recycling used prod-
ucts.

13
ENGLISH
Controls on the back
AC ~ Connection socket for power cable
supplied.
LIFT
AC~
Handle.
Battery compartment
cover.
Controls on the bottom
P ••P
x
Disables and enables the buttons.
The display
I00.6. MHz FM
M2
§ e
O
P
1
1
Appears and flashes if the batteries
are low (not for auxiliary batteries or if
the device is connected to the mains
power cable).
e Displays alarm stand-by with signal
tone.
§ Displays alarm stand-by with radio
station.
≤ The sleep timer is activated.
P The key lock is activated.
I00.6 Frequency, time, alarm time or sleep
timer display.
I00.6. Shows the change of frequency in
50 kHz steps.
M Flashes when storing a radio station
on a preset button, displays the stati-
on when stored.
2 Displays the preset position on the
preset button.
MHz Frequency display.
FM Shows the waveband (VHF).
See the figure on page 3.
Controls on the top
ON/OFF Switches the device on and off.
p For opening the telescopic antenna.
LIFT
PRESETS
1, 2, 3, 4, 5 Preset buttons for storing and selec-
ting radio stations.
+ 5 Activates the second level of preset
buttons 1, 2, 3, 4, 5.
SNOOZE Interrupts the alarm function.
MEM. Stores radio stations on the preset
buttons 1, 2, 3, 4, 5 (preset stations
1-5, preset stations 6-10 together
with + 5).
Controls on the front
– TUNING Press briefly to decrease the frequen-
cy in steps of 50 kHz. Hold down to
start a reverse station search.
For setting the clock and alarm
(hours).
+ TUNING Press briefly to increase the frequen-
cy in steps of 50 kHz. Hold down to
start a forwards station search.
For setting the clock and alarm
(minutes).
SLEEP For setting the sleep timer.
MODE Activates the clock and alarm setting,
press once to briefly display the time
during radio mode or twice to display
the alarm time.
ALARM Activates the alarm function, ends
alarm stand-by.
Controls on the sides
+ VOL. – Adjusts the volume.
e § Switches between signal sound and
radio program for alarm mode.
§ TONE ! For setting the tone.
0 Earphone socket (3.5 mm stereo
plug).
Mono playback via earphones.
Note:
7
Excessive sound pressure from the earphones
can cause hearing loss.
OVERVIEW _____________________________________________________________

ENGLISH
14
Mains operation
Check that the mains voltage on the type plate (on the
bottom of the device) corresponds to your local mains
supply. If this is not the case, contact your specialist
dealer.
1 Plug the mains cable supplied into the »AC ~« so-
cket on the device.
LIFT
AC~
2 Plug the mains cable into the socket (230V~,
50/60 Hz).
Note:
7
If there are batteries in the device, these are swit-
ched off automatically during mains operation.
Caution:
7
The device is connected to the mains with the
power cord. Pull out the power cord when you
want to completely disconnect the device from
the mains.
7
Unplug the mains plug to disconnect the device
from the mains. Make sure the power plug is eas-
ily accessible during operation and not hindered
by other objects.
Battery operation
You can also operate the device using standard batte-
ries (not supplied). In this case, you must disconnect the
mains power cable.
1 Open the battery compartment by pressing the area
marked with arrows on the drawing and pushing
down the cover.
LIFT
AC~
RESET
AC~
POWER SUPPLY _____________________________________________________
2 Insert four batteries (4x1.5V, Type IEC, AM 2, LR
14, C size) according to the polarity marked on the
battery compartment.
Note:
7
Do not expose the batteries to extreme heat,
caused for example by direct sunlight, heaters
or fire.
7
Remove the batteries when they are flat or when
you know that the device will not be used for
a long period of time. When the batteries are
low, a battery symbol appears and flashes in the
display. This function does not work when the
power cable is plugged into the device.
7
No liability is accepted for damage resulting
from leaking batteries.
Environmental note:
7
Batteries, including those which contain no hea-
vy metal, must not be disposed of with household
waste. Please dispose of used batteries in an en-
vironmentally sound manner. Observe the legal
regulations which apply in your area.
Inserting back-up batteries
During mains operation, the back-up batteries ensure
that stored settings are not lost in the case of a power
failure or when the device is briefly disconnected from
the mains. If no main batteries are inserted and there is
no mains power supply, you have approximately 10
seconds to change the back-up batteries.
1 Open the battery compartment by pressing the
area marked with arrows on the drawing and push-
ing down the cover.
LIFT
AC~
RESET
AC~
2 When inserting the batteries (micro type, e.g. AM
3, LR 6, AA size) in the small compartment, observe
the polarity marked on the compartment base.

15
ENGLISH
SETTINGS ________________________________________________________________
Tuning and storing radio stations
When the device is first connected to the mains or the
batteries are first inserted, the device begins an auto-
matic search and stores the first ten stations with strong
signals on the preset buttons 1, 2, 3, 4, 5. You can stop
this search by pressing »MEM.«.
However, you can also tune stations manually and store
them on the preset buttons.
1 Press »ON/OFF« to switch on the device.
– You will hear the radio station last selected.
2 Keep briefly pressing »– TUNING« or »+ TUN-
ING« until you have found the frequency you
want.
– Display: the frequency changes in steps of 50
kHz
or
Hold down »– TUNING« or »+ TUNING« for
approximately 1 second.
– Display: the automatic search stops at the next
station with a strong signal.
3 Briefly press »MEM.« to activate the memory func-
tion.
– Display: »M« flashes.
Note:
7
If you do not press any button within 3 seconds,
the device will quit memory mode without mak-
ing any changes.
4 Press the required preset button »1, 2, 3, 4, 5« (pre-
set stations 1 to 5).
– Display: e.g. »3«, »M« flashes
or
Press »+ 5« and the required preset button »1, 2,
3, 4, 5« (preset stations 6 to 10).
– Display: e.g. »8«, »M« flashes.
5 Press »MEM.« again to store the station.
– Display: the frequency, »M« and, for example
»3« or »8«.
Setting the clock
When you first use the device, you first have to set the
clock.
1 With the device switched off, keep pressing
»MODE« until the time flashes in the display.
Note:
7
If you do not press any button within 3 seconds,
the device will quit set-up mode. Any altered set-
tings will be stored.
2 Press »– TUNING« briefly to set the hours step-
by-step or hold it down to run through the hours
quickly.
3 Press »+ TUNING« briefly to set the minutes step-
by-step or hold it down to run through the minutes
quickly.
4 Press »MODE« to confirm the setting.
– Display: the current time.
Setting the alarm time
1 Press »ON/OFF« to switch off the device.
– Display: the current time.
2 Press »MODE« briefly.
– Display: the alarm time most recently set, »§«
or »e« flashes.
3 Keep pressing »MODE« until the alarm time flash-
es in the display.
Note:
7
If you do not press any button within 3 seconds,
the device will quit set-up mode. Any altered set-
tings will be stored.
4 Press »– TUNING« briefly to set the hours step-
by step or hold it down to run through the hours
quickly.
5 Press »+ TUNING« briefly to set the minutes step-
by-step or hold it down to run through the minutes
quickly.
6 Press »MODE« to confirm the setting.
– Display: the set alarm time, »§« or »e« flash.
– After a short time, the display changes to the cur-
rent time.

ENGLISH
16
OPERATION ___________________________________________________________
Switching on and off
1 Press »ON/OFF« to switch the device on and off.
Radio operation
For the best FM (VHF) reception, it is sufficient to extend
the telescopic antenna and direct it accordingly.
Selecting stored stations
1 Select the station you want using the preset buttons
»1, 2, 3, 4, 5« (preset stations 1 to 5) or using »+
5« and the preset buttons »1, 2, 3, 4, 5« (preset
stations 6 to 10).
Adjusting the volume
1 Adjust the volume using »+ VOL –«.
Adjusting the tone
1 Adjust the tone using »§ TONE !«.
Displaying the current time
1 Press »MODE« to briefly display the time.
– The display changes from the frequency to the
time and back.
Alarm mode
Alarm with signal tone
1 Press »ON/OFF« to switch off the device.
2 Set the alarm signal tone (»e«) on the right of the
device using »e §«.
3 Press »ALARM« to select the alarm function.
– Display: the current time and »e«.
4 Briefly press »MODE« to check the alarm time.
– Display: the set alarm time, »e« flashes.
– After a short time, the display changes to the cur-
rent time, »e« no longer flashes.
– The alarm goes on with a signal tone at the set
time.
Alarm with radio station
1 Press »ON/OFF« to switch on the device.
2 Select the radio alarm (»§«) on the right of the
device using »e §«.
3 Select the radio station using the preset buttons »1,
2, 3, 4, 5« or using »+ 5« and the preset buttons
»1, 2, 3, 4, 5«.
4 Set the alarm volume using »+ VOL –«.
5 Press »ON/OFF« to switch off the device.
6 Press »ALARM« to select the alarm function.
– Display: the current time and »§«.
7 Briefly press »MODE« to check the alarm time.
– Display: the set alarm time, »§« flashes.
– After a short time, the display changes to the cur-
rent time, »§« no longer flashes.
– The radio switches on at the set alarm time.
Briefly displaying the alarm time
1 With the device switched off, press »MODE«.
– The display changes from the clock to the set
alarm time, – display: »e« or »§« flash.
– After a short time, the display changes back to the
current time.
Interrupting the alarm
1 Press »SNOOZE« while the alarm is sounding.
– Display: »e« or »§« flash.
– The alarm (signal tone or radio) stops.
– The alarm goes on again at 5-minute intervals
(the total alarm time is 90 minutes).
Cancelling the alarm for the day
1 Press »ON/OFF« while the alarm is sounding.
– Display: the current time and »e« or »§«.
– The alarm (signal tone or radio) stops, but the
alarm function remains activated for the next day
at the set time.
Cancelling alarm stand-by
1 Press »ALARM« to cancel alarm stand-by.
– Display: »e« or »§« disappears.
– The set alarm time is saved.
2 Press »ALARM« to re-activate alarm stand-by.
– Display: »e« or »§«.

17
ENGLISH
OPERATION ___________________________________________________________
Timer mode
The device possesses a sleep timer, which it switches off
in radio mode at a preset time. It is possible to set nine
switch-off times between 90 and 10 minutes.
Switching on the sleep timer
1 Press »SLEEP« to switch on the device.
– Display: » ≤« and » 9 0 « .
– You will hear the radio station last selected.
2 To set the switch-off time (90, 80, 70, 60, 50, 40,
30, 20, 10), press »SLEEP« as many times as ne-
cessary.
– Display: » ≤« , briefly, for example » 3 0 « ,
then the frequency.
Note:
Briefly press »SLEEP« to check the remaining
switch-off time.
Switching off the sleep timer
1 To switch off the sleep timer early, keep pressing
»SLEEP« until » 0« briefly appears in the display.
– Display: » ≤« disappears.
– The device switches off.
General information
Disabling the buttons
1 Use »P/Px« on the bottom of the device
to disable the buttons.
– Display: »P«.
2 Use »P/Px« on the buttom of the device
to enable the buttons again.
– Display: »P« disappears.
Deleting all settings
Interrupt the power supply for at least 2 minutes to reset
the device to its original state. All settings are lost when
you do this.
1 Remove all the batteries – including the back-up
batteries.
2 Pull out the power cable and wait for at least 2
minutes before plugging it in again.
– The time, alarm time and radio settings are de-
leted.

Grundig Intermedia GmbH
Beuthener Strasse 41
90471 Nürnberg
www.grundig.com
72011 409 9100 13/02