Grundig RR 760 CD User manual

RR 720/760 CD page 1
RR 720/760 CD

2
RR 720/760 CD page 2
NOTES
©Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved moulded 13 Amp plug. To
change a fuse in this type of plug proceed as follows:
• Remove fuse cover and fuse.
• Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI
approved type.
• Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut
off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5 Amp.
If a plug without a fuse is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed to avoid a possible shock
hazard should it be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code:
blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour markings
identifying the terminals in your plug, proceed as follows:
•
Connect the blue wire to the terminal marked N or coloured black.
• Connect the brown wire to the terminal marked L or coloured red.
• Do not connect either wire to the earth terminal in the plug,
marked E (or e) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead – not simply over the two wires.
iDichiarazione di conformità ai sensi del
D.M. 28.08.95, n. 548
Si dichiara che gli apparecchi illustrati nel pre sente libretto di istru-
zioni per l'uso rispondono alle prescrizioni dell'articolo 2, comma 1,
del Decreto Ministeriale 28 Agosto 1995, n. 548.
Fatto a Fürth il 24/08/1998
GRUNDIG Fernseh-Video Produkte und Systeme GmbH
Kurgartenstraße 37
D-90762 FUERTH
VORSICHT – UNSICHTBARE LASER-
STRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST.
NICHT DEM STRAHL AUSSETZEN.
CAUTION – INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
ADVARSEL – UNSYNLIG LASER-
STRALING NAR DEKSEL APNES
UNNGA EKSPONERING FOR
STRALEN.
ADVARSEL – UNSYNLIG LASER-
STRÅLING VED ÅBNING.
UNDGÅ UDSETTELSE FOR STRÅLING.
VARNING – OSYNLIG LASER
STRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR
URKOPPLAD.
BETRAKTA EJ STRÅLEN.
VARO – AVATTAESSA JA SUOJA-
LUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE
LASERÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
ALLGEMEINE HINWEISE FÜR GERÄTE
MIT LASER
GENERAL INSTRUCTIONS FOR LASER
UNITS
GENERELLE HENVISNINGER FOR
LASER-APPARATER
ALLMÄNNA FÖRESKRIFTER FÖR
LASER-UTRUSTNING
LASER-LAITTEITA KOSKEVIA
HUOMAUTUKSIA
LUOKAN 1
LASERLAITE
KLASS 1 LASER
APPARAT
VARNING!
OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA BRUKS-
ANVISNING SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR
OSYNLIG LASERSTRÅLNING,
SOM ÖVERSKRIDER GRÄNSEN FÖR
LASERKLASS 1.
VAROITUS
LAITTEEN KÄYTTÄMINEN MUULLA
KUIN TÄSSÄ KÄYTTÖOHJEESA
MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN I YLITTÄVÄLLE
NÄYKYMÄTTÖMÄLLE
LASERSATEILYLLE.
FALLS ERFORDERLICH
IF APPLICABLE
HVIS NØDVENDIG
HVIS DET KREVES
CLASS 1
LASER PRODUCT

Deutsch Seite
Wartung ....................................4
Bedienelemente .......................4–6
Stromversorgung..........................6
Allgemein...................................7
Klangregulierung .........................7
Radio ........................................8
CD Spieler ...........................9–11
Cassettendeck.....................11–12
Technische Daten.......................13
Fehlersuche ..............................13
English Page
Maintenance ............................14
Controls .............................14–16
Power supply............................16
General...................................17
Sound control ...........................17
Radio ......................................18
CD Player...........................19–21
Cassette deck .....................21–22
Technical specifications...............23
Troubleshooting .........................23
Français Page
Entretien...................................24
Contrôles............................24–26
Alimentation..............................26
Général...................................27
Contrôle du son ........................27
Radio ......................................28
Lecteur de CD .....................29–31
Platine cassette ....................31–32
Caractéristiques techniques..........33
Dépistage des pannes................33
Italiano Pagina
Manutenzione...........................34
Controlli .............................34–36
Alimentazione...........................36
Generalità................................37
Controllo del suono....................37
Radio ......................................38
Lettor CD............................39–41
Deck a cassette ...................41–42
Dati tecnici...............................43
Elenco ricerca guasti..................43
Português Página
Manutenção.............................44
Controlos............................44–46
Alimentação .............................46
Geral ......................................47
Controlo do som .......................47
Rádio ......................................48
Leitor de CD .......................49–51
Leitor de cassetes.................51–52
Dados técnicos .........................53
Resolução de problemas.............53
Español Página
Mantenimiento ..........................54
Controles............................54–56
Alimentación.............................56
General...................................57
Control de sonido......................57
Radio ......................................58
Lector de CD ......................59–61
Deck a casete.....................61–62
Datos técnicos ..........................63
Localizacíon de averías ..............63
Nederlands Pagina
Onderhoud ..............................64
Knoppen ............................64–66
Stroomvoorziening .....................66
Algemeen ................................67
Klankregeling............................67
Radio ......................................68
CD-Speler...........................69–71
Cassettedeck.......................71–72
Technische gegevens..................73
Foutzoeklijst ..............................73
Dansk Side
Vedligeholdelse .........................74
Kontroller............................74–76
Forsyning .................................76
Generelt ..................................77
Lydkontrol.................................77
Radio ......................................78
CD-afspiller.........................79–81
Kassette-deck.......................81–82
Tekniske data............................83
Fejlfinding ................................83
Svenska Sida
Underhåll .................................84
Kontroller............................84–86
Strömförjning ............................86
Allmänt ....................................87
Ljudkontrollen ............................87
Radio ......................................88
CD-Spelaren .......................89–91
Kassettspelaren....................91–92
Tekniska data............................93
Felsökning................................93
Suomi Sivu
Hoito.......................................94
Säätimet.............................94–96
Käyttöjännite.............................96
Yleistä .....................................97
Äänensäätö..............................97
Radio ......................................98
CD-Soitin..........................99–101
Kasettidekki.....................101–102
Tekniset tiedot .........................103
Tarkistusluettelo ........................103
3
RR 720/760 CD page 3
D
GB
F
I
P
E
NL
DK
S
FIN
INDEX
PostScript Picture
Kundenberatungslogo

General
• The mechanical parts of the CD player and the cassette deck
contain self-lubricating bearings and must not be oiled or
lubricated.
• A chamois leather slightly moistened with water is sufficient
for cleaning the housing.
• Do not use cleaning agents as these may harm the housing.
• Do not leave the set, batteries, CDs or cassettes for any length of
time in direct sunlight or other places where high temperatures
can occur, such as in the vicinity of heating apparatus.
• Do not expose the set, batteries, CDs or cassettes to humidity
or rain.
Positioning the set
Caution should be exercised if the set is placed on furniture as
surfaces are often coated with lacquers and plastic finishes
containing additives which attack the material of which the feet
of the set are made, leaving stains which can only be removed
with difficulty or not at all.
CD player maintenance
• The lens Xmust not be cleaned.
• This product should be used in dry and closed rooms. The
lens may cloud over if the CD player is moved from cold to
warm surroundings. The CD player will not start. Do not clean
the lens, but give the player some time to acclimatise.
Cassette deck maintenance
To ensure a good recording and playback quality, clean the
indicated parts ABC after every 50 hours of operation or, on
average, once a month.
• Open the cassette holder using 9//.
• Use a cotton bud slightly moistened with alcohol or a special
head cleaning fluid.
•
Press Band clean the rubber pressure rollers C.
• Then press ;and clean the capstans Band the heads A.
• After cleaning, press 9//.
• Cleaning of the heads Acan also be done by playing a
cleaning cassette through once.
Top and front panel
p– connection for headphones
VOLUME – to adjust the volume.
SURROUND – to switch the surround sound
effect
SOUND – on and off
FUNCTION
– CD: to switch to CD mode
– TAPE: to switch to TAPE mode
– RADIO: to switch to RADIO mode
ANTENNA – telescopic aerial for FM
reception
DIGITAL SOUND CONTROL DSC – to select the
desired sound effect: CLASSIC,
ROCK or POP.
OPEN/CLOSE – to open and close the CD door
STANDBY – to switch the unit on and off
STANDBY 6– goes out when the unit is on
REMOTE – to receive the remote signals
SENSOR (only RR 760 CD)
Back panel
Battery compartment: – for inserting 8 batteries
type R20, UM1 or D-cells.
Back up battery compartment: – for inserting 2
batteries type R6,UM-3 or AA-
cells
AC MAINS – Socket for mains lead.
This unit meets the CEE regulations
concerning interference radiation.
This product fulfills European
directives 89/336/EEC,
73/23/EEC and 93/68/EEC.
This unit complies with the safety
regulations according to VDE 0860
/ BS 415 and thus with the
international safety regulation
according to IEC 65.
The type plate is located at the
bottom of the set.
A A B C
X
MAINTENANCE CONTROLS
14
RR 720/760 CD page 14
GB

Display (illustration: RR 760 CD)
The display indicates:
CLASSIC, ROCK, POP: the selected sound effect.
TAPE: when cassette deck is selected
Blights up during CD playback
;lights up during the CD pause mode
INTRO: lights up during the INTRO function
REPEAT: lights up = repeat all
flashing = repeat one
RANDOM:
lights up during the RANDOM function
CH: indicates the radio memory channel
TRACK: indicates the CD track
MEMORY: programming or programme play-
back (CD) or storing stations (radio)
ɳ: lights up when receiving FM stereo
stations
VOLUME: (only RR 760 CD) lights up when
adjusting the volume indicated in dB
MW/FM/LW
: indicates the selected waveband
88 track number (CD) or memory
channel (radio)
88:8.85: playing time (CD) or station
frequency (radio)
MHz/kHz: for FM reception the frequencies
are indicated in MHz and for
MW/LW reception in kHz
FM
MW
LW kHz
MHz
CHTRACK MEMORY
INTRO REPEAT RANDOM
CLASSIC ROCK POP TAPE
VOLUME
dB
Radio
(FUNCTION switch in position RADIO)
PROG. – to store the radio stations
DOWN Q– to tune backward
UP R– to tune forward
BAND – to select between FM, MW,
and LW waveband
MEM 34 –
to select the next/previous
memory position
Cassette
(FUNCTION switch in position TAPE)
0– to start recording
B– to start cassette playback
Q– fast rewind
R– fast forward
9//– to stop and eject the cassette
;– to interrupt and continue
playback and recording
CD
(FUNCTION switch in position CD)
PLAY/PAUSE 2; – to start and interrupt
playback
STOP 9– to stop playback
PROG. – to programme track numbers
in the memory
R-SKIP Q– to skip and search
backward
F-SKIP R– to skip and search forward
INTRO – to play only the first 10
seconds of each title
REPEAT – to repeat one/all tracks
RANDOM – to play the titles of a CD in
random order
CONTROLS
15
RR 720/760 CD page 15
GB
ANTENNA
TAPE DIRECTION
VOL
CD
TAPE
RADIO
CASSETTE
ANTENNA
FUNCTION
VOLUME
OPEN/CLOSE
STANDBY
DIGITAL SOUND
CONTROL
CD/RADIO
PLAY/
PAUSE
STOP
STANDBY
PROG
UP/
F-SKIP
DOWN/
R-SKIP
REPEAT
RANDOM
INTRO
BAND
MEM
RR 760 CD
RADIO CASSETTE RECORDER WITH CD
s
u
r
r
o
u
n
d
s
o
u
n
d
D
I
G
I
T
A
L
S
O
U
N
D
C
O
N
T
R
O
L
REMOTE
SENSOR
SURROUND SOUND
the picture shows: RR 760 CD

Remote control (only RR 760 CD)
The buttons on the remote control have the same
functions as the corresponding buttons on the
unit.
Note:
When using battery supply, the ybutton can
only be used to switch the unit off.
To switch the unit on when using battery supply,
use the STANDBY button on the set
(see 'Switching on and off').
Changing batteries
If the range of your infrared remote control seems
to decrease, or if certain functions can no longer
be carried out, you should replace the batteries.
Two batteries 1.5 Volt LR03, size AAA batteries
are required.
To change the batteries, open the compartment
on the back of the remote control. Ensure that the
batteries are inserted properly (note the markings
in the compartment).
Battery Supply
• Open the battery compartment and insert as
shown 8 batteries, type R20, UM1 or D-cells.
• Remove the batteries if exhausted or if they
will not be used again for a long period.
– The battery supply is switched off when the set
is connected to the mains.
• To change over to battery supply, pull out the
plug from the AC ~ socket.
Back-up batteries for preset memory
In order to keep the presets stored in the memory
during the time that the power supply is
interrupted (e.g. when changing the batteries), it
is necessary to insert two additional batteries.
• Place these batteries size LR 6, AA, alkaline
type in the battery compartment.
• These batteries should always be inserted,
regardless of the power supply (mains voltage
or batteries).
– No responsibility can be accepted for
damage due to leaking batteries.
Mains supply
• Check if the mains voltage as shown on the
type plate (at the bottom of the set) corresponds
to your local mains voltage. If it does not,
consult your dealer or service organisation.
• Connect the mains lead to the AC ~ socket
and the wall socket.
– The mains supply is switched on.
• To disconnect the set from the mains complete-
ly, withdraw the mains plug from the wall
socket.
AC ~
Important note for users in the U.K.
When fitting a mains plug, follow the
instructions on page 2.
Note on Environmental Protection
Do not throw exhausted batteries in the
household refuse.
Hand over the old batteries to your dealer or
public collecting points when buying new ones.
CONTROLS POWER SUPPLY
16
RR 720/760 CD page 16
GB

Volume
• Adjust the volume to the desired level with the
VOLUME control.
Surround Sound
This feature creates an additional 3-D effect from
stereo sound which is relayed by the speakers.
• Press SURROUND SOUND to switch this effect
on and off
wSURROUND SOUND OFF
xSURROUND SOUND ON
Digital Sound Control (DSC)
The DSC feature creates a realistic atmosphere
for the style of music you select using the latest
digital sound technology.
• Press the DSC button on the unit or on the
remote control until the desired sound effect is
shown on the display: CLASSIC, ROCK or
POP.
Stereo headphone socket p
• You may connect stereo headphones having a
3.5 mm plug to the jack p.
– Inserting the plug will disconnect the speakers.
Switching on and off
• Press the STANDBY button to switch the unit
on.
– The STANDBY indicator 6goes out when the
unit is on.
• To switch the unit off press the STANDBY
button again.
– The STANDBY indicator 6lights up.
•When using mains supply, you can also use
the ybutton on the remote control (only RR
760 CD) to switch the unit on and off.
•When using battery supply, you can only
switch the unit on via the STANDBY button on
the set (the STANDBY indicator 6goes out).
This is done to save battery life.
However, you can switch the unit off via the
remote control.
Source selection
• Select the desired source by switching the
FUNCTION switch in the respective position
(CD, TAPE or RADIO).
GENERAL
17
RR 720/760 CD page 17
GB
Note:
The volume and sound control settings
have no effect on cassette recording.
SOUND CONTROL

Radio aerials
– For FM, pull out the telescopic aerial. To
improve FM-reception, incline and turn the
aerial.
Reduce its length if the FM-signal is too strong
(very close to a transmitter).
– For MW/LW, the set is provided with a built-
in aerial, so the telescopic aerial is not
needed. Direct the aerial by turning the whole
set.
Radio reception
• Set the FUNCTION switch to RADIO.
• Adjust the sound using the VOLUME, DSC and
SURROUND SOUND controls.
• You may connect stereo headphones having a
3.5 mm plug to the jack p.
– Inserting the plug will disconnect the speakers.
• Select the wave band using the BAND button.
• Start the automatic station search by holding
the UP 22 or DOWN 11 button down for
one or two seconds, and then releasing it.
– The tuner automatically searches for the next
station with sufficient signal strength.
• Repeat this step to search for other stations.
• To tune to a weak station, briefly press the
UP 22 or DOWN 11 buttons several times
until the correct frequency is displayed, or until
reception is best.
– When 'ɳ' appears on the display, you are
receiving an FM stereo transmitter.
Storing stations
You can store a maximum of 40 stations
(20 x FM, 10 x MW and 10 x LW).
• Select the wave band using the BAND button.
• Select the desired station with the UP 22 or
DOWN 11 buttons.
• Press the PROG. button.
–'MEMORY' starts flashing on the display.
• Select within 5 seconds the channel you wish
to assign to this station with the MEM 3or 4
buttons. If not, you will leave the function
without storing the station.
•While 'MEMORY' is flashing, press PROG. to
store this station.
–'MEMORY' disappears from the display.
The display now indicates the station's
assigned channel, its frequency and
waveband.
• If you assign a station to a channel that had
been previously assigned to a different station,
the old station is deleted and replaced by the
new one.
Selecting stations
• Select the wave band using the BAND button.
• Select the desired memory channel with the
MEM 3or 4button.
– The display indicates the selected channel, the
station frequency and waveband.
Last station memory
LAST STATION MEMORY means that the unit
'remembers' the last frequency that was tuned to.
This function ensures that the station which was
selected before the radio was switched off is
automatically selected again when your radio is
switched back on.
RADIO
18
RR 720/760 CD page 18
GB
FM
MHz
LW kHz
CH
FM
MW
LW kHz
FM
MHz
CH
FM
MHz
CH MEMORY

Playing a CD
• Press PLAY/PAUSE 2; to start playback.
– The display shows the current track number
and its elapsed playing time.
• Adjust the sound using the VOLUME, DSC and
SURROUND SOUND controls.
• For brief interruptions, press PLAY/PAUSE 2;.
•
To resume playback, press PLAY/PAUSE 2;
again.
• To stop playback, press STOP 9.
– The total playing time and number of
tracks will then appear on the display.
– The CD player also goes to position STOP:
– when the end of the CD is reached;
– if the FUNCTION switch is moved to another
position
– if the batteries run down or if the power sup-
ply is interrupted.
• To take out the CD, open the CD door by
pressing OPEN/CLOSE.
• Open the CD door only if the CD player is in
position STOP.
Selecting another track during play
• Press R-SKIP Qor F-SKIP Runtil the
required track number appears in the display.
– The selected track begins to play.
Starting with a particular track
• Press R-SKIP Qor F-SKIP Runtil the
required track number appears in the display.
• Press PLAY/PAUSE 2;.
– Play starts from the selected track.
TRACK
TRACK
TRACK
TRACK
TRACK
OIOIOIOIOIOIOIOIOIOIOI
OIOIOIOIOIOIOIOI
OIOIOOOIOI
OIOIOIOIOOIOI
OIOIOIOOIOOIOIOI
CLASS 1
LASER PRODUCT
6.OYEMICANTO(HearMyVoice)
7.DON'TWANNALOSEYOU
8.GETONYOURFEET
9.YOURLOVEISBEDFORME
10.CUTSBOTHWAYS
11.OYEMICANTO(SpanishVersion)
12.SIVOYAPERDERTE
EPC4651452
BIEM/STEMRA
STEREO
Allrightsoftheproducerandoftheowneroftherecordedworkreserved.Unauthorisedcopying,
publicperformance,broadcasting,hiringorrentalofthisrecordingprohibited.MadeinAustria
1.AY,AY,I
2.HEREWEARE
3.SAY
4.THINKABOUTYOUNOW
5.NOTHIN'NEW
COMPACT
DIGITALAUDIO
1
2
CD handling
• Use only Digital Audio CDs which have the
symbol ʀ.
• To take the CD out of its box easily, press the
centre spindle while lifting the CD.
• Never write on a CD or attach any sticker to the
CD.
• Always hold the CD at the edge and always
store it in its box after use with the label facing up.
• To remove dust and dirt, breathe on the CD
and wipe it with a soft, lint-free cloth in a
straight line from the center towards the edge.
Cleaning agents may damage the CD.
• Do not expose the CD to rain, moisture, sand,
or to excessive heat. (E.g. from heating equip-
ment or in motor cars parked in the sun).
Warning
CLASS 1 LASER PRODUCT means that the laser´s
construction makes it inherently safe so that the
legally prescribed maximum permissible ratiation
values can never be exceeded.
CAUTION: Using any equipment or devices
other than those described and specified in these
operating instructions, or tampering with the unit
in any
way, can result in dangerous exposure to
radiation.
Inserting a CD
• Set the FUNCTION switch to CD.
• Press OPEN/CLOSE to open the CD door.
• Insert the CD, printed side facing up.
• Close the CD door.
–
The CD player scans the contents list of the CD.
After that, the total number of tracks and the
total playing time appear on the display.
CD PLAYER
19
RR 720/760 CD page 19
GB

Playing a CD
Searching for a passage during play
• Hold R-SKIP Qdown to search backwards
to the beginning.
• Hold F-SKIP Rdown to search
forwards to
the end.
Note: This function can be described as
'audibly' searching for a title.
During the search, volume is reduced and returns to
i ts adjusted level as soon as the button is released.
Random
• Press the RANDOM button.
–'RANDOM' lights up on the display.
• Press PLAY/PAUSE 2;.
– The tracks are played in random order until all
of them have been played once.
•
By pressing RANDOM during playback, random
play starts from the end of the playing track.
• The function is deactivated by pressing
STOP 9(in which case the CD stops) or
RANDOM; in this case the remaining tracks
are played in their normal order.
• The random function is not possible during
playback of a programme.
Intro
• Press INTRO to play only the first 10 seconds
of each title.
–'INTRO' lights up on the display.
After the last title, the CD player stops.
• The function is deactivated by pressing
STOP 9(in which case the CD stops) or
INTRO; in this case the remaining tracks are
played back in the normal way.
Repeat
Repeating the CD
• By pressing REPEAT once, all tracks are
repeated.
–'REPEAT' lights up; the CD will now be
repeated continuously.
Repeating a track
• By pressing REPEAT twice, one track is
repeated.
–'REPEAT' starts flashing; the actual track will
now be repeated continuously.
• To switch the repeat mode off, press REPEAT
one more time, or press STOP 9.
Programming
By programming the player you can play up to
20 tracks in any desired order. If you exceed the
maximum of 20 tracks, the programme function
will start again from the beginning.
Storing a programme
• In STOP mode, press PROG..
'MEMORY' and 'TRACK' start flashing.
•
Select the first desired track using R-SKIP Q
or F-SKIP R .
• Store this track by pressing PROG. again.
• Select and store in this way all desired titles.
• Press PLAY/PAUSE 2; to start playback of the
programme.
Checking the programme
• In STOP mode, press PROG. repeatedly: The
display shows in sequence all programmed
track numbers.
• Press PLAY/PAUSE 2; to start playback of the
programme.
TRACK MEMORY
TRACK
REPEAT
TRACK
REPEAT
TRACK
INTRO
TRACK
RANDOM
CD PLAYER
20
RR 720/760 CD page 20
GB

Compact cassettes
–Copyright: Recording is permissible insofar as
copyright or other rights of third parties are not
infringed.
• For recording, use a NORMAL (IEC type I)
cassette on which the tabs are not broken out.
– This deck is not suited for recording on
CHROME (IEC II) or METAL (IEC IV) cassettes.
• For playback, any cassette type may be in-
serted.
– At the very beginning and end of the tape, no
recording will take place during the few
seconds when the leader tape passes the
recorder heads.
• To prevent the accidental erasure of a record-
ing, keep the cassette side to be safeguarded
in front of you and break out the left tab.
Now, recording on this side is no longer pos-
sible.
• To render this safeguard ineffective, cover the
hole with a piece of adhesive tape.
• Do not expose the cassettes to rain, moisture,
sand, or to excessive heat. (E.g. from heating
equipment or in motor cars parked in the sun)
• Do not store cassettes near strong magnetic
fields (for example, TV sets, speakers, engines,
etc.).
1
1
TRACK
TRACK MEMORY
TRACK MEMORY
Changing the programme
Adding tracks to the programme
• Press PROG. repeatedly until the display shows
the first empty memory location
(under TRACK appears 00).
• You can now add tracks to the sequence as
described above (up to 20).
Replacing previously programmed tracks
• Press PROG. repeatedly until the display
shows the step you wish to replace.
• Select the track you want to enter in its place.
• Store this track by pressing PROG..
Playing a programme
• Press PROG. once to show the first track of the
programme.
• Press PLAY/PAUSE 2;.
–
Play starts with the first track of the programme.
– After the last track playback stops.
– The CD's total playing time and number of
tracks appear on the display.
Note:
• Press STOP 9to stop playback.
• While playing a programme, it is possible to
use R-SKIP Qor F-SKIP Rto select the
desired programmed tracks.
Erasing a programme
• To clear the programme, press the PROG.
button and afterwards STOP 9.
– You can only erase the programme when the
CD player is stopped.
• The programme is also erased:
– by opening the CD door using OPEN/CLOSE;
– if you move the FUNCTION selector;
– if the batteries are exhausted or if the power
supply is interrupted in another way.
CASSETTE DECKCD PLAYER
21
RR 720/760 CD page 21
GB

Cassette playback
• Set the FUNCTION switch to TAPE.
–‘TAPE’ lights up on the display
• Press 9//to open the cassette holder.
• Insert a recorded
cassette with the open
side downward and the
full spool on the left.
• Adjust the sound using
the VOLUME, DSC and
SURROUND SOUND controls.
• You may connect stereo headphones having a
3.5 mm plug to the jack p.
– Inserting the plug will disconnect the speakers.
• Press Band playback will start.
• For brief interruptions, press ;.
• To restart playback, press this button once
more.
– When the end of the tape is reached the B
button is released.
• To stop, press 9//.
On pressing again, the cassette holder will
open.
Winding the tape
• Press Rto search forward to the end of the
tape.
• Press Qto search backward to the
beginning of the tape.
• To stop, press 9//.
– When the end of the tape is reached, the
recorder buttons are automatically released.
CASSETTE DECK
22
RR 720/760 CD page 22
GB
Cassette recording
• Press 9//to open the cassette holder.
• Insert the cassette.
• When monitoring during
recording, adjust the
sound using the controls
VOLUME, DSC and
SURROUND SOUND.
These controls do not affect the recording.
• Start recording by pressing 0.
(the Bbutton is automatically also pressed).
– When the end of the tape is reached, the 0
and Bbuttons are automatically released.
• To interrupt recording, press ;.
• To continue recording, press ;again.
• Press 9//if you want to stop recording
before the end of the tape.
On pressing again, the cassette holder will
open.
Recording from the CD player
(CD synchro recording)
• Set the FUNCTION switch to CD.
• It’s not necessary to start the CD player sepa-
rately: by pressing 0the CD player starts
automatically.
– If the CD player is in STOP position, recording
will start from the beginning of the CD (or from
the beginning of the programmed selection).
• To start a recording in the middle of a track,
play the CD in the normal way.
• As soon as the desired passage is reached,
pause the CD and then start recording by
pressing 0.
Recording from the radio
• Set the FUNCTION selector to RADIO.
• Select the wave band using the BAND button.
• Select the desired station with the UP 22 or
DOWN 11 buttons or with the MEM 3or 4
buttons.
• Start recording by pressing 0.

If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate
the guarantee.
PROBLEM POSSIBLE CAUSE REMEDY
General
No sound VOLUME not adjusted Adjust the VOLUME
Headphones are connected Disconnect headphones
Batteries are exhausted Insert fresh batteries
Batteries are incorrectly inserted Insert the batteries correctly
Mains lead is not securely connected Connect the mains lead properly
Set does not react to Electrostatic discharge Switch off the set, disconnect the mains
operation of any button plug, reconnect after a few seconds
Radio
Poor radio reception Weak radio aerial signal Aim the aerial for best reception:
FM: incline and rotate telescopic aerial
AM (MW/LW): rotate the entire set
Interference caused by the vicinity of Keep the radio away from electrical
electrical equipment like TVs, video equipment
recorders, computers, thermostats,
fluorescent lamps, engines etc.
Cassette
Poor cassette sound Dust and dirt on the heads, capstan Clean the heads etc..
quality or pressure roller See Maintenance
Recording does not Cassette tab(s) may be broken out Apply a piece of adhesive tape over
work the missing tab space
CD
The CD skips tracks CD is damaged or dirty Replace or clean the CD
PROGRAM or RANDOM is active Switch off PROGRAM or RANDOM play
Power Supply
Mains operation ..................230 Volt, 50/60 Hz
Battery operation ...............8 x 1.5 V (R20, UM1)
Back-up batteries for radio presets ...2 x 1.5 V (AA)
Output power DIN 45324, 10% THD
Music power:..............................2 x 4500 mW
Nominal power ...........................2 x 2500 mW
Socket for stereo headphones:..............3.5 mm ø
Radio section
Wavebands:......................FM 87.5 – 108 MHz
.....................................MW 522 – 1620 kHz
.........................................LW 146 – 281 kHz
Aerials:...........................Telescopic aerial for FM
...................Built in ferrite rod aerial for MW/LW
Cassette section
Cassette:............Compact cassette to DIN 45516
Track system:...................International quartertrack
Tape speed: .................................4.76 cm/sec.
Motor: ...............................................DC motor
Frequency range:.......................125 Hz – 8 kHz
S/N ratio, weighted..............................≥45 dB
Wow and flutter: ..................................≤0.35%
Automatic functions: ..Automatic recording level control
....................Automatic button release at tape end
CD section
Frequency range:.......................20 Hz – 20 kHz
S/N ratio, weighted .............................> 68 dB
General
Dimensions (bxhxd) ............426 x 253 x 188 mm
Weight (w/o batteries) .................approx. 4.7 kg
Accessories
....................................................Mains Cable
............................................Instructions for Use
(only RR 760 CD).........................Remote control
.............2 x 1.5 V batteries for remote, type AAA
Subject to technical alterations and alterations in
styling E. and O.E.
TROUBLESHOOTINGTECHNICAL DATA
23
RR 720/760 CD page 23
GB

GRUNDIG AUDIO INTERNACIONAL. 04701 BRAGA 0PORTUGAL 0 1 2 3 4 5 6 7 8 9 72010-756.95 / MM07.98