GTO RB709U-NB User manual

RB709U-NB
Relay Output Universal Receiver
Owners Manual
The RB709U-NB digital receiver is a
wireless radio control designed for
use with automated gate openers and
garage door openers. The receiver has
two channels for receiving signals from
two activation devices; i.e. transmit-
ters, multi-button transmitters, wireless
keypads, etc.
www.gtoaccess.com
Specications
Compatible transmitter:
• Linear PRO Access or Mighty Mule gray narrow band transmitters (318MHz)
Power input:
• 8-24 V ac/dc, 10ma standby, 40ma activated (Red & Black wires).
Outputs: 2 channels pulsed outputs
• 2 channels dry-contact normally open relay outputs.
• Channel 1: Blue (N/O Contact) & Green (COM) wires.
• Channel 2: Yellow (N/O Contact) & Brown (COM) wires.
• Activated for .5 seconds when the correct transmitter code is received.
• Relay switching maximum rating: 24Vac/dc @ 1A.
• Operating Range 50 to 100 feet (15.2 to 30.5 m)
Indoor/Outdoor compatible.
Mount receiver at least 3 feet from AC power source.
Mounting the Receiver Connect Receiver to Relay Inputs and Power
Consider the following when mounting the receiver:
• Standard receiver cable length is 10 feet (3.05 m).
• For exterior applications run the cable through PVC
conduit to protect it from damage.
• DO NOT run cable in conduit containing ac wiring.
• The receiver range can vary from 50 to 100 feet (15.2
to 30.5 m) depending upon weather, topography, and
external interference.
FCC Regulation
This device complies with FCC rules Part 15. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept an interference that may cause undesired operation.
Transmitter distance may vary due to circumstances beyond our control. NOTE: The manufacturer is not
responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such
modications could void the user’s authority to operate the equipment.
NOTE: Do not mount upside down in exterior applications.
Channel 1 (To COM)
Channel 1 (To N/O Contact)
Channel 2 (To COM)
Channel 2 (To N/O Contact)
2nd GATE OPERATOR or DOOR OPENER
1st GATE OPERATOR or DOOR OPENER
8 to 24 VOLT AC/DC
POWER SUPPLY
RED WIRE to POSITIVE
BLACK WIRE to NEGATIVE
RED
BLACK
GREEN
BLUE
BROWN
YELLOW
Designed to work with most brands of gate and door
openers.
Printed in China for GTO Access Systems, LLC
rev-12/09/14

Programming the Receiver
Wiring Receiver to Common Gate and Door Openers Wiring Receiver to GTO DC Operators
Wiring Receiver to GTO GP-SL50 & GP-SW50 Operators
Programming transmitter(s) or other access devices to RB-709U-NB receiver:
• Press and hold the transmitter (device) button to be learned.
• Press the‘LEARN CH1’ (or ‘LEARN CH2’) button on the RB-709U-NB receiver for 1-2
seconds or until the red LED turns on, then release the button.
• Note: When the correct code is received and the corresponding relay output is
activated, the red LED will turn on.
Channel 1 (GREEN WIRE to COM)
Channel 1 (BLUE WIRE to CYCLE)
BLACK
RED
Channel 2 (BROWN WIRE to COM)
Channel 2 (YELLOW WIRE to N/O Contact)
ALARM
ACC. POWER DUAL CABLE
+12Vdc
COM
DUAL LINK
LINK COM
RELAY OUTPUTS
LOCK N.C.
LOCK COM
LOCK N.O.
RUN 1 RUN 2
CLOSED 1 CLOSED 2
CYCLE
SAFETY
OPEN EDGE
RUN 2
OPEN
CLOSE
STOP
COM COM COM
SHADOW
LOOP
Check operation after programming:
• Press Transmitter (device) button, #1 - RED LED blinks once to conrm.
• Press Transmitter (device) button, #2 - RED LED blinks twice to conrm.
GP-SL50 and GP-SW50 Contol Board
Typical Linear PRO Access or Mighty Mule DC powered gate operators.
PRO 2000XLS, 3000XLS. 4000XLS, and Mighty Mule 500/560, 502/562
6 5 4 3 2 1
Genie Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Linear Garage Door Opener
PUSHBUTTON
COMMON
BEAM
ANTENNA
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Lift Master
Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Chamberlin
Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Lift Master SL580 Gate Opener
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
CHANNEL 1 (N/O)
CHANNEL 2 (N/O)
CHANNEL 1 (COM)
CHANNEL 2 (COM) RED WIRE to POSITIVE POWER
BLACK WIRE to NEGATIVE POWER
BATTERY or
TRANSFORMER
SURGE PROTECTOR
(RB570 or R4215)
Channel 1 (GREEN WIRE to COM)
Channel 1 (BLUE WIRE to CYCLE/CLOSE)
BLACK
RED
Channel 2 (YELLOW WIRE to COM)
Channel 2 (BROWN WIRE to N/O Contact)
GRN BLK RED
RECEIVER
COM COM
CYCLE
CLOSE
SAFETY
EXIT
OPEN
SHADOW
LOOP
CLOSE
EDGE
OPEN
EDGE
J11 J8 J12
8 to 24 VOLT AC/DC
POWER SUPPLY or BATTERY
RED WIRE to POSITIVE
BLACK WIRE to NEGATIVE
BATTERY or
TRANSFORMER
SURGE PROTECTOR
(RB570 or R4215)
GTO Access Systems, LLC • 3121 Hartseld Road • Tallahassee, Florida 32303 • Sales 1-800-543-4283 • Technical Support 1-800-543-1236 • www.gtoaccess.com
Connects to most garage
door openers the same as a
remote push button.