GTW MACH 01-176 User manual

1
2
Remove hardware from struts and take off
canopy. Retain hardware. You will need it
later.
Remove hardware from gutters. Retain
hardware from gutters. You will need it later.
Remove gutters by sliding them upward.
WILL FIT YAMAHA DRIVE 2 (2017-UP)
installation instructions
gtw mach rear flip seat
mach 1 steel : 01-176, 01-177, 01-178
mach 2
aluminum : 01-179, 01-180, 01-181
included:
Pack 1
6 - 10x25mm hex bolt
12 - 10mm at washer
6 - 10mm lock nut
2 - 8mm lock nut
2 - 10x90mm hex bolt
4 - 10mm at washer
2 - 10mm lock nut
2 - 6x35mm hex bolts
2- 6mm at washers
2 - 6mm fender washers
2 - 6mm lock nuts
Pack 2
6 - 10x70mm hex bolt
2 - 10mm countersunk #3 bolts
14 - 10mm at washers
6 - 10mm lock nuts
2 - rubber spacers
2 - 10mm acorn nuts
Pack 3
4 - 6x25mm hex bolt
4 - 6mm lock washers
4 - 6mm at washers
Pack 4
2 - 10x45mm hex bolt
4 - 10mm at washers
2 - 10mm lock nuts
Pack 5
8 - 8x35mm countersunk bolts
HARDWARE
Main Brackets
Bagwell Brackets

3
4
5
6
Remove rear strut from both sides. Retain all
hardware. You will need it later.
Remove seat back. Retain hardware. You
will need it later.
Remove basket and retain hardware
A) Attach new main brackets with strut
mounts pointing to the outside of cart. Use
retained hardware from previous step.
B) Attach rear struts to main brackets using
retained hardware from STEP 3
(A)
(B)

7
8
9
10
Attach front bracket brace to brackets using
hardware from pack 1.
Attach seat back to brackets using hardware
retained from step 4.
Place bagwell bracket in bagwell as shown.
Install 6x35mm bolts from pack 1 in outer
holes and hand tighten. Measuring 3.5” from
the inside edge of the bagwell nearest to the
bumper mark drill location using predrilled
hole of bracket as guide.
REAR BUMPER
DRIVER SIDE
Using a 13/32” bit, drill hole through bagwell
and all the way through frame. Install
10x90mm bolts from pack 1 and tighten all
hardware from STEP 10 & 11.
NOTE: Gas models will need motor mount
bolt under cart removed before drilling
REAR BUMPER
PASSENGER SIDE

1
1
1
2
3
4
1
1
Attach bagwell bracket using hardware
from pack 1.
Attach seat frame to bagwell brackets using
hardware from pack 2.
Attach seat back support and armrests to
seat frame using hardware from pack 2.
Be sure to use rubber spacers from
hardware pack 2 between seat back
support and armrest as shown.

15
16
17
18
Attach armrests to rear portion of seat
frame using hardware from pack 2.
(A) Attach footrest bagwell bracket using
remaining hardware from pack 1.
(B) Attach footrest brackets to footrest and
armrest using remaining hardware from
pack 2.
Attach seat back brackets to seat back
using hardware from pack 3 and tighten.
Attach seat back to seat back support using
hardware from pack 4. Now you can tighten
all hardware.

INSTALLATION COMPLETE
19
20
Attach seat bottom and strap to seat frame
using hardware from pack 5.
Insert gutters and attach canopy using
hardware from step 1.