Guntermann & Drunck DVI-CPU-UC Installation guide

Target Modules and
User Modules
Guntermann & Drunck GmbH
www.gdsys.de
A9200136-2.21
EN Installation and Operating Guide
Standard variants

i· Target and user modules
About this manual
This manual has been carefully compiled and examined to the state-of-the-art.
G&D neither explicitly nor implicitly takes guarantee or responsibility for the qual-
ity, efficiency and marketability of the product when used for a certain purpose that
differs from the scope of service covered by this manual.
For damages which directly or indirectly result from the use of this manual as well
as for incidental damages or consequential damages, G&D is liable only in cases of
intent or gross negligence.
Caveat Emptor
G&D will not provide warranty for devices that:
Are not used as intended.
Are repaired or modified by unauthorized personnel.
Show severe external damages that was not reported on the receipt of goods.
Have been damaged by non G&D accessories.
G&D will not be liable for any consequential damages that could occur from using
the products.
Proof of trademark
All product and company names mentioned in this manual, and other documents
you have received alongside your G&D product, are trademarks or registered trade-
marks of the holder of rights.
© Guntermann & Drunck GmbH 2015. All rights reserved.
Version 2.21 –30/01/2015
Guntermann & Drunck GmbH
Dortmunder Str. 4a
57234 Wilnsdorf
Germany
Phone [phone]
Fax [phone]
http://www.GDsys.de
[email protected]

Table of Contents
Target and user modules · ii
Table of Contents
Safety instructions ............................................................................................ 1
Chapter 1: Target modules
Target module »DVI-CPU« .............................................................................. 3
Target module »DVI-CPU-UC« ........................................................................ 7
Target module »DVI-CPU-MC2« ................................................................... 11
Target module »DVI-CPU-MC2-UC« ............................................................ 16
Target module »DVI-CPU-Fiber« ................................................................... 22
Target module »DVI-CPU-Fiber-UC« ............................................................ 27
Target module »DP-CPU« .............................................................................. 32
Target module »DP-CPU-UC« ....................................................................... 36
Target module »VGA-CPU-UC« .................................................................... 40
Target module »U2-R-CPU« ........................................................................... 44
Chapter 2: User modules
User module »DVI-CON« ............................................................................... 47
User module »DVI-CON-MC2« ..................................................................... 53
User module »DVI-CON-MC4« ..................................................................... 60
User module »DVI-CON-Fiber« ...................................................................... 68
User module »DVI-CON-2« ........................................................................... 74
User module »DP-CON« ................................................................................ 80
User module »DP-CON-2« ............................................................................. 86
User module »U2-R-CON« ............................................................................. 92
User module »DVI-CON-12V« ....................................................................... 95
User module »DVI-CON-Video« .................................................................. 101

Table of Contents
iii · Target and user modules
Chapter 3: Generic HID
Enabling/disabling the user module’s Generic HID mode ............................ 106
Enabling/disabling the target module’s Generic HID mode .......................... 107
Chapter 4: Extender mode
Opening the on-screen display in extender mode ........................................... 108
Configuration ............................................................................................... 109

Safety instructions
Target and user modules · 1
Safety instructions
Please read the following safety instructions carefully before you start operating the
G&D product. The instructions well help in avoiding damages to the product and in
preventing possible injuries.
Keep this manual handy for all persons who will be using this product.
Follow all warnings or operating instructions which are on the device or stated in
this user manual.
, Beware of electric shocks
To avoid the risk of electric shock, do not open the device or remove the covers.
If service is required, please contact our technicians.
, Disconnect the main power plug or the power supply before installation
Before installation, ensure that the device has been disconnected from the power
source. Disconnect the main power plug or the power supply of the device.
, Ensure constant access to the power plugs
During the installation of the devices, ensure that the power plugs remain accessible.
, Do not cover the ventilation openings
Ventilation openings prevent the device from overheating. Do not cover them.
! Avoid tripping hazards
Avoid tripping hazards while laying cables.
, Only use a grounded voltage source
Operate this device by using a grounded voltage source.
, Use only the provided G&D power pack
Operate this device with the provided G&D power pack or with the power pack
listed in the manual.
! Operate the device only in designated areas.
The devices are designed for indoor use. Avoid exposure to extreme cold, heat
or humidity.

Safety instructions
2· Target and user modules
Special instruction for dealing with laser technology
The Fiber devices of the target modules and user modules use components with laser
technology which comply with laser class 1.
They meet the requirements according to EN 60825-1:2007 and EN 60825-
2:2004+A1:2007 as well as U.S. CFR 1040.10 and 1040.11.
Mind the following instructions when dealing with laser beams:
! Avoid eye contact with invisible laser beam
Do not look directly into the beam using optical instruments.
! Always connect optical connections or cover them with protection caps
When not in use, optical connections of the Transmission sockets as well as cable
plugs must always be covered with a connector or a protection cap.
! Only use G&D certified transmission modules
It is not allowed to use transmission modules that do not comply with laser class 1
according to EN 60825-1:2007. By applying such modules, the compliance of the
given instructions and recommendations for laser safety cannot be guaranteed.
The guarantee of complying with all relevant instructions can only be given by
applying original components. The devices must therefore only be operated
G&D certified transmission modules.
LASER CLASS 1
DIN EN 60825-1:2001-11
Complies with 21 CFR
1040.10 and 1040.11
Invisible laser beam,
avoid exposure with
optical instruments

Target and user modules · 3
Target module »DVI-CPU«
With DVI-CPU target modules, you can connect a computer with DVI graphics out-
putto a digital matrix switch of the ControlCenter-Digital or the DVICenter series.
Users at the consoles of the matrix switch can access the target module and operate
the connected computer.
Package contents
1 × DVI-CPU target module
1 × Video cable (DVI-D-SL)
1 × USB device cable
1 × Twin-PS/2 cable
2 × Audio cable
1 × Power pack (12V/24W)
1 × Power cable
Required accessories
1 × Category 5e (or better) patch cable to connect the target module to the
matrix switch
ATarget modules

Target module »DVI-CPU«
4· Target and user modules
Installation
Connecting target computers
Keyb.: Use the purple plug of a Twin-PS/2 cable to connect the purple PS/2 socket
(keyboard) to this port.
Mouse: Use the green plug of a Twin-PS/2 cable to connect the green PS/2 socket
(mouse) of the computer to this port.
USB K/M: Use the USB device cable to connect one of the computer’s USB ports to this
port.
DVI-D CPU: Use the video cable to connect the digital video output of the computer to
this port.
Line In: Use an audio cable to connect the Line-Out interface of the computer to this port.
Line Out: Use an audio cable to connect the Line-In interface of the computer to this port.
Connection to the matrix switch
Trans: Use a category 5e (or better) twisted pair cable to connect this interface to one
of the Dynamic Port (RJ45) provided at the matrix switch.
NOTE: Both keyboard and mouse signals can be transmitted to the computer using
the PS/2 or the USB ports.
ADVICE: You can also connect the target module directly to a compatible user module.
MouseKeyb. DVI-D CPUUSB K/M
  




Target module »DVI-CPU«
Target and user modules · 5
Power supply
Power In: Plug the power cable of the power pack in this interface. Then connect the
power cable to the power pack and a power outlet.
Status displays
The LED on the back panel of the target module shows the status of the external
power pack:
The blinking Transmission LEDs signal the following operating statuses:
LED Status Meaning
Power on The external power pack is connected and the required voltage (12 Volt)
is available.
off The external power pack is not (properly) connected.
LED Status Meaning
Yellow Off No user module accesses the target module.
On A user module accesses the target module.
Blinking The incoming video signal was not detected.
Flashing No voltage at PS/2 interface or USB bus.
Green Off The target module is turned off.
Blinking The power pack is connected and supplies the required power.
The connection to the matrix switch could not be established.
Flashing The connection to the matrix switch is established.
No user module is accessing or the computer is turned off.
On A user module accesses the target module.
A computer is connected and turned on.
Flickering Keyboard and mouse inputs are transmitted by the accessing user module.
The flickering is defined by the user’s inputs.

Target module »DVI-CPU«
6· Target and user modules
Technical data
DVI-CPU
Interfaces to
computer: Video: 1 × DVI-D (Single Link)
Keyboard and mouse signals: 2 × PS/2 socket
1 × USB-B
Audio: 2 × 3,5 mm jack socket
Data transmission
to matrix switch Interface: 1 × RJ45 socket
Transmission length Max. 140 metres
Video Resolution @ 60 Hz: Max. 1920 × 1200 pixels
Colour depth: 24 bits
Pixel rate: 25 MHz to 165 MHz
Vertical frequency: 50 Hz to 180 Hz
Horizontal frequency: 30 kHz to 130 kHz
Norms: DVI 1.0, E-DDC
Audio Type: Bi-directional extension
Resolution: 24 Bit
Sampling rate: 96 kHz
Bandwidth: 22 kHz
Power supply Type: Power pack(12V/2A)
Connection: 1 × Mini-DIN 4 socket
Current consumption: Max. 500mA @ 12VDC
Casing Material: Anodised aluminium
Dimensions (W × H × D): 105 × 26 × 104 mm
Weight: Approx. 240 g
Operating
environment Temperature: +5 to +45 °C
Air humidity: < 80%, non-condensing
Conformity CE, RoHS