GUTA GT107-2 User manual




Model No. GT107-2
Scan here to contact us
[24Hrs Online]
https://guta.afterservice.vip

Contents
Product Components
Button and Icon Description
System Programming
1. Wireless Programming
2. Inflation Programming
Delete Sensor’s ID Code
1. Delete Single Sensor ID Code
2. Delete all Sensors ID Code
System Parameter Settings
1. Factory Default Setting
2. Product Specifications
3. Parameter Settings
System Alerts
Safety Cautions
Warranty Information
Contact Us
---------------------------------------------
-------------------------------------------
-------------------------------------------
-------------------------------------------
-----------------------------------------
--------------------------------------
-------------------------------------------
-------------------------------------------
-----------------------------------------------
---------------------------------------------------------
----------------------------------------------------
--------------------------------------------
-------------------------------------------------------------
----------------------------------
----------------------------------
---------------------------------
1
1
2
2
4
6
6
7
9
9
9
10
14
17
19
20

Product Components
Button and Icon Description
Item
Display
Micro USB Cable
Suction cup
Dashboard Mount
Sensor Number Sticker
User Manual
Repeater
1pc
1pc
1pc
1pc
1pc
1pc
Optional
Quantity


System Programming
1. Wireless Programming
Step 1:
Icons Descriptions
Tire Icon Sensor Low
Battery Indicator
Monitor Power
Indicator
Trailer1, Trailer2,
Trailer3
Repeater
Indicator
Temperature Unit
Pressure Unit
Alert Icon
Icons Descriptions
In the Standby mode, press and hold the“CODE” button
for 3 seconds with a beep to enter the Learning mode, and
the current tire“ ”is flashing. On the screen, a“FFF
FFF”will be displayed as below to indicate no sensor has
been programmed to the current tire.


Step 2:
Press the “+”/ “-” button to select the desired tire.
Step 3:
Step 4:
Place the sensor onto the top right of the monitor (next
to the “ ” Label).
Short press the “CODE” button once with a “Bi”, a
red LED will start flashing and the sensor ID code will be
displayed on the screen.
Step 5:
Press the “+” button to work on the next tire, or hold
and press the “CODE” button for 3 seconds to store
the operation.
If there is a “BiBi”, it indicates that the programming
failed. Try Step 3 again to work on the sensor until the
monitor displays the sensor ID.


Note:
2. Inflation Programming
If users do not press any button within 1 minute, the
monitor will exit the Learning mode and the current
pressure value will be displayed.
Step 2: Press the “+” / “-” button to select the
desired tire.
Step 3: Install the sensor on the desire tire until you
hear a “Bi”, followed by a red flashing LED and the
sensor ID code being displayed on the screen.
Step 1: In the Standby mode, press and hold the
“CODE” button for 3 seconds to enter the Learning
mode with a beep. The selected tire “ ” will flash. An
“FFF FFF” will be displayed as below to indicate no
sensor has been programmed to the current tire.


Note:
Tips：
Note: If there is a “BiBi”, it indicates program failed.
Please try Step 3 again to work on the sensor until the
monitor displays the sensor ID.
Step 4: Press the “+” button to work on the next tire,
or hold and press the “CODE” button for 3 seconds to
store the operation.
If users do not press any button within 1 minute, the
monitor will exit the Learning mode and the current
pressure value will be displayed.
One sensor could only be programmed to one tire if
the sensor is programmed more than once on
different tires, the monitor will memorize the latest
tire location.
1


1. Delete Single Sensor ID Code
Press “+” and “-” buttons simultaneously to
stop programming and return to the Standby mode
without saving the operation.
Delete sensor ID and all sensor IDs could be operated
in this operation too. For details please refer to the
instructions below.
Step 1: In the Standby mode, press and hold the
“CODE” button for 3 seconds to enter the Learning
mode with a beep. The selected tire “ ” will flash. An
“FFF FFF” or a six digits ID code will be displayed on
the screen.
2
3
Delete Sensor’s ID Code


2. Delete All Sensors ID Code
Step 2: Select the desired tire you want to delete by
Pressing the “+” or “-” button.
Step 3: Hold and press the “-” button for about 3
seconds and release it after a beep. There will be an
“FFF FFF” displayed on the screen, which indicates
that the sensor ID has been deleted successfully.
Step 4: Long press the “SET” button for 3 seconds to
save operation and return to the Standby mode.
Note: If users long press the “CODE” button for 3
seconds without saving operation then the product will
return to the Standby mode.
Step 1: When the monitor is in Standby mode, Users can
press and hold the “CODE” button for 3 seconds to enter
Learning mode with a beep. The selected tire “ ” will
flash. And a “FFF FFF” or a six digits ID code will be
displayed on the screen.


Step 2: Hold and press the “-” button. Do not release
it until you hear the “BiBi”, which indicates that all the
sensor IDs have been cleared.
Step 3: Shortly press the “SET” button to save the
above operation and return to the Standby mode.


1. Factory Default Setting
Reference Setting Pressure
High Pressure Alert
Low Pressure Alert
High Temperature Alert
Pressure Unit
Temperature Unit
131 PSI (9 BAR)
164PSI (11.3 BAR)
98 PSI (6.8 BAR)
194°F (90℃)
PSI
°F
2. Product Specifications
System Parameter Settings
Pressure Range
Working
Storage
Frequency
Input Voltage
Weight
Size (L x W x H)
0-188 PSI (0- 13 BAR)
-40°F ~ 76°F(-40℃ ~+80℃)
-40°F ~ 85°F(-40℃ ~ +85℃)
433.92MHz
5-24V
99x76x25 mm
118g


3. Parameter Settings
In the Standby mode, hold and press the “SET”
button for about 3 seconds. Do not release until a beep
to do the parameter settings.
Step 1: Firstly you will see the pressure unit PSI or BAR
flashes, press “+” or “-” button to select the unit
you use.
Step 2: After selecting the pressure unit, please shortly
press the “SET” button to choose the temperature
unit of ℃ or °F.


Step 3: After setting the temperature unit, shortly press
the “SET” button to set the HIGH & LOW PRESSURE
ALERT parameter of each truck axle, the first and second
number of the 1st axle tire pressure value will flash.
Shortly press the“+” or “-” button to set the desired
pressure.


Step 4: After setting the HIGH&LOW PRESSURE ALERT
parameter of each truck axle , shortly press the “SET”
button to set the HIGH&LOW PRESSURE ALERT parame-
ter of T1 trailer and the tire pressure value second
number will flash. Shortly press the “+” or “-”
button to set the desired pressure.
Press the “CODE” button to set the third number
while it is flashing. After setting the pressure parameter,
repeat Step 3 to set the HIGH & LOW PRESSURE ALERT
parameter for all the truck axle.


Press the “CODE” button to set the next number while
it is flashing. After setting the pressure parameter, repeat
Step 4 to set the HIGH & LOW PRESSURE ALERT parame-
ter for T2, T3 truck. Long press the “SET” button to
save the above operation and return to the Standby
mode.


1. High-Pressure Alert
2. Low-Pressure Alert
The monitor will alert with beeps. The corresponding
faulty tire “ ”and “ ” will flash when the tire
pressure is higher than the high- pressure alert parameter.
The monitor will alert with beeps. The corresponding
faulty tire “ ” and “ ”will flash when the tire
pressure is lower than the high-pressure alert parameter.
System Alerts


3. High-Temperature Alert
4. Fast Leakage Alert
The monitor will alert with beeps. All tires pressure value
change into a temperature value. The corresponding
faulty tire “ ” and “ ” will flash when the tire
pressure is higher than the high- temperature alert
parameter.
If leakage happens in one tire over 3 PSI within one
minute, the monitor will display an alert, the corre-
sponding faulty tire “ ” and “ ” will flash.


5. Lost Sensor Signal
When the monitor has not received one of the sensor's
signal for more than 1 hour, the corresponding faulty tire
“ ”and “ ” will flash pressure and temperature
value will disappear.
Please stop the vehicle in a safety area to check the
no signal tire and the sensor. Try to reprogram the
sensor to the tire.
If changed to a new trailer, the monitor will update
new trailer data when changing the trailer successful-
ly. e.g. 3 trailers have been programmed (T1, T2, T3).
When the truck with the T1 trailer changed into the T2
trailer, the monitor T1 data will update to T2 data.
Tips:
1
2


6. Sensor Low Battery Alert
When a sensor is low battery, “ ” and “ ”will
flash as below, please change the battery.
It is highly recommended to read the instructions below
before installing the system:
The monitor should be installed inside the vehicle
where it does not affect normal driving.
The monitor should be well fixed to avoid falling off
during driving.
The tires' temperature and pressure will be increased
while driving. The vehicle should be stopped if there is
high temperature or high pressure alert in case of
brake problem or flat tire.
Safety Cautions
1.
2.
3.


Driver should stop the vehicle and get off to check the
tire fast leakage occurs or the pressure goes up
quickly in the tire.
Be ware of flat tire when there is high pressure and
take care of fuel consumption and balance while
suffering from low pressure.
The system can effectively monitor tire pressure and
temperature but cannot prevent traffic accident.
Regular tire inspection and maintenance is still
necessary.
Be ware of driving safety while checking tire data on
the way of driving.
After the system is installed correctly, the driver does
not need to stare at the monitor all the time while
driving.
The monitor will be in the Sleeping mode to save
battery life if the motion sensor detects the vehicle
has stopped for a while. It will turn on automatically
when it detects the vehicle is moving again. If one of
the sensor data has not been display on the monitor
at the beginning, the data will be displayed Later
when there is pressure or temperature changes.
The signal transmission from the monitor and sensors
is wireless, a signal repeater is necessary for long
4.
5.
6.
7.
8.
9.
10.
