GW Instek PEL-2000A Series User manual

Programmable DC Electronic
Load
PEL-2000A Series
USER MANUAL
GW INSTEK PART NO. 82EL-2004AEA1
ISO-9001 CERTIFIED MANUFACTURER
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

January 2016
This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of the Good Will company.
The information in this manual was correct at the time of printing.
However, Good Will continues to improve products and reserves
the right to change specification, equipment, and maintenance
procedures at any time without notice.

Table of Contents
3
Table of Contents
SAFETY INSTRUCTIONS ................................................... 5
GETTING STARTED ......................................................... 10
Main Features ...................................... 12
Series Overview ................................... 13
Package Contents and Accessories....... 15
Measurement Overview ....................... 16
Front Panel Overview ........................... 17
Display Overview –Mainframe ............ 23
Rear Panel Overview ............................ 27
Front Panel Overview –Load Module... 30
LED Display Overview –Load Module.. 34
Installation .......................................... 37
Load Connections ................................ 45
Frame Link Connection ........................ 57
Channel Control Connection ................ 59
Go/NoGo Connection .......................... 62
OPERATING DESCRIPTION............................................. 63
Operating Mode Description ............... 64
Parallel Unit Mode ............................... 75
Run Program........................................ 77
Sequence ............................................. 80
OCP Test Automation .......................... 85
Parallel Dynamic Loading .................... 86
Configurations Description .................. 87
Interface and File System ..................... 97
TUTORIALS....................................................................104
Local loads ........................................ 105
Single Channel Load .......................... 107

PEL-2000A Series User Manual
4
Parallel Load Modules........................ 109
Programming ..................................... 111
Sequences .......................................... 113
Frame Link ......................................... 114
Channel Control ................................. 116
General Configuration Options .......... 118
OPERATION ...................................................................119
Local Mode Operation ....................... 123
Mainframe Basic Operation ............... 130
Creating a Program Sequence ............ 156
Edit Sequence .................................... 169
OCP Test Automation......................... 179
Channel Configuration ....................... 186
Mainframe Configuration ................... 215
Interface Configuration (settings) ...... 230
Save / Recall ...................................... 236
INTERFACE ....................................................................267
Interface Configuration ...................... 268
FAQ ...............................................................................276
APPENDIX .....................................................................277
Fuse Replacement .............................. 277
Firmware Update ............................... 278
Calibration ......................................... 279
Range Chart ....................................... 280
Default Settings ................................. 285
Specifications .................................... 287
Dimensions ....................................... 298
EC Declaration of Conformity ............. 300
INDEX............................................................................301

SAFETY INSTRUCTIONS
5
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow when operating
the PEL-2002A/PEL-2004A, and when keeping it
in storage. Read the following before operating
the PEL-2002A/2004A to ensure your safety and
to keep the PEL-2000A series in the best possible
condition.
Safety Symbols
These safety symbols may appear in this manual or on the PEL-
2002A/2004A.
WARNING
Warning: Identifies conditions or practices that
could result in injury or loss of life.
CAUTION
Caution: Identifies conditions or practices that
could result in damage to THE PEL-2002A/2004A
or to other properties.
DANGER High Voltage
Attention Refer to the Manual
Protective Conductor Terminal
Earth (ground) Terminal

PEL-2000A Series User Manual
6
Do not dispose electronic equipment as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.
Safety Guidelines
General
Guideline
CAUTION
Do not place any heavy object on the PEL-
2002A/2004A.
Avoid severe impact or rough handling that
leads to damaging the PEL-2002A/2004A.
Do not discharge static electricity to the PEL-
2002A/2004A.
Do not block or obstruct the cooling fan vent
openings.
Do not perform measurement at circuits directly
connected to Mains (Note below).
Do not disassemble the PEL-2002A/2004A
unless you are qualified as service personnel.
The equipment is not for measurements
performed for CAT II, III and IV.
(Measurement categories) EN 61010-1:2010 specifies the
measurement categories and their requirements as follows. The
PEL-2002A/2004A falls under category I.
Measurement category IV is for measurement performed at the
source of low-voltage installation.
Measurement category III is for measurement performed in the
building installation.
Measurement category II is for measurement performed on the
circuits directly connected to the low voltage installation.
Measurement category I is for measurements performed on
circuits not directly connected to Mains.

SAFETY INSTRUCTIONS
7
Power Supply
WARNING
AC Input voltage: 115V/230V switchable,
50/60Hz
The power supply voltage should not fluctuate
more than 15%.
Connect the protective grounding conductor of
the AC power cord to an earth ground, to avoid
electrical shock.
Fuse
WARNING
Fuse type: T3.15A/250V
Make sure the correct type of fuse is installed
before power up.
To avoid fire, only replace the fuse with the
specified type and rating.
Disconnect the power cord before fuse
replacement.
Make sure the cause of a fuse blowout is fixed
before replacing the fuse.
Cleaning the
PEL-2000A
Disconnect the power cord before cleaning.
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
Do not use chemicals or cleaners containing
harsh material such as benzene, toluene, xylene,
and acetone.
Operation
Environment
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
Temperature: 0°C to 40°C
Altitude: Up to 2000m
Transient Overvoltage on the main supply is
2500V.

PEL-2000A Series User Manual
8
(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees
and their requirements as follows. THE PEL-2002A/2004A falls
under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Storage
environment
Location: Indoor
Relative Humidity: < 80%
Temperature: −10°C to 70°C
Disposal
Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.

SAFETY INSTRUCTIONS
9
Power cord for the United Kingdom
When using the PEL-2002A/2004A in the United Kingdom, make
sure the power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
Green/ Yellow:
Earth
Blue:
Neutral
Brown:
Live (Phase)
As the colours of the wires in main leads may not correspond with the coloured
marking identified in your plug/appliance, proceed as follows:
The wire which is coloured Green & Yellow must be connected to the Earth
terminal marked with either the letter E, the earth symbol or coloured
Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal which is
marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal marked
with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or contact the
supplier.
This cable/appliance should be protected by a suitably rated and approved
HBC mains fuse: refer to the rating information on the equipment and/or user
instructions for details. As a guide, a cable of 0.75mm2 should be protected by a
3A or 5A fuse. Larger conductors would normally require 13A types,
depending on the connection method used.
Any exposed wiring from a cable, plug or connection that is engaged in a live
socket is extremely hazardous. If a cable or plug is deemed hazardous, turn off
the mains power and remove the cable, any fuses and fuse assemblies. All
hazardous wiring must be immediately destroyed and replaced in accordance
to the above standard.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com

PEL-2000A Series User Manual
10
GETTING STARTED
This chapter describes the features and functions of the
PEL-2002A/2004A, including the front and rear panel
appearance, panel installation and connection types. Use
the Tutorial section for quick access to step by step
instructions on the main functions.
Main Features ................................................................. 12
Series Overview............................................................... 13
Package Contents and Accessories .................................. 15
Measurement Overview ................................................... 16
Front Panel Overview ...................................................... 17
Display Overview –Mainframe ........................................ 23
Rear Panel Overview........................................................ 27