H2O LIFE SOURCE DuoGuard JCP-K201 User manual

DG - KX Purifier
Purity with simplicity
Operation Manual
Ver2_103032021
DuoGuardTM
· Please read this manual carefully before using the product and keep it well after reading.
· it cannot be used where the power specification is different.
· The appearance and specifications of the product are subject to change without notice.

1
DuoGuard - 4-stage filtration & one-touch auto dispense.
Choice of 150ml, 500ml & 1litre.
We don't just Redefine.
We Simplify your drinking water. .
A. Product Features
B. Caution for Safety
C. Caution for Installation
D. Installation
E. Name on Parts
F. How to Use
G. Caution for Use
H. How to Clean
I. Hygienic Care of the Product
J. Filter Functions and Filter Replacement Time
K. How to Replace the Filters
L. Product Specifications and Water Flow Diagram
M. Troubleshooting
2
3 - 4
5
6
7
8
9
10
11
12
13
14
15

2
1. Direct type water purifier without water tank
It is more hygienic because you can have clean purified water right away.
2. Compact tabletop water purifier
It is a compact water purifier that can be installed easily in small kitchen
spaces, effectively utilizing the space.
3. Pre-set amount of water for auto-dispense
Frequently used volume at 150ml, 500ml & 1 litre have been pre-set for
your convenience.
4. Easy filter replacement
The filter can be replaced easily on your own without the need for
technical assistance.
5. Enhanced convenience with button indicators on the control panel
The display blinks to indicate the operating status of the purifier. This
blinking light is very useful at night.
6. Latest material technology used
Matt aluminum alloy is used not only for a sleek look but more so
for strength and high wear resistance in both the filter housing.
7. Removable drip tray
Magnetic drip tray can be attached and detached easily for cleaning,
and can be conveniently removed when larger containers are used
for collecting water.
A. Product Features

3
•Please use the product safely and correctly to prevent accidents and dangers.
• Cautions are classified into two categories, "Warnings" and "Cautions," depending on
the degree of risk and the amount of damages that may occur when the label
is violated.
Use only the specified power source. (This product is for 24V 0.6A only.)
Safety accidents can be prevented.
Always unplug it when not in use or before cleaning the inside of the product.
Safety accidents can be prevented.
If the power cord is damaged, ask your call center to change the cord to
avoid risk.
Do not use a damaged or loose outlet. There is a danger of electric shock or fire.
If dust or water gets on the pins or contacts of the power plug, clean them with a
dry cloth.
Dirt or water, etc., may cause an electric shock or fire.
Do not use several electrical appliances at the same time on one power outlet.
Abnormal heat generation of the outlet may cause fire.
Insert the power plug all the way into the power outlet.
Incomplete connection may cause fire.
Do not touch the power plug with wet hands.
There is a risk of electric shock.
Do not pull out the power cord. Be sure to pull out the power plug.
If the power cord is damaged, there is a danger of electric shock or fire.
Be careful not to bend the power cord excessively or place a heavy object on it.
There is a danger of electric shock or fire.
Do not place candles, cigarettes, etc. on the appliance or place them near
heat sources.
There is a danger of electric shock or fire.
Do not place bowls of water, chemicals, or small metals on top of the product.
These things may cause an electric shock or fire.
When moving the product, shut off the water, drain the filter water completely,
and unplug the power plug before moving it.
It may cause product damage or electric shock.
B. Caution for Safety
In case of violation of
the label, serious injury
or death may occur.
Violation of the label may
cause injury or property
damage and deterioration
of the product.
Warning
Warning
Warning
on
installation
Power
Caution

4
Do not install on inclined or unstable places.
It may cause deterioration and fall, causing injury or failure.
When installing, be careful not to step on or trip over the power cord.
Do not install the product in a humid place, near inflammables, in a location
exposed to snow or rain, or where the ambient temperature below 0oC.
It may cause deterioration and fall, causing injury or failure.
Do not operate the appliance without leveling.
It may cause the malfunction or product failure.
Do not tilt more than 45° when transporting the product.
If tilted too hard, it may cause performance degradation.
Do not lean on or hang the product loosely.
There is a danger of the product falling, causing injury.
Do not allow children to play with the device.
Parental care is required.
If the product is damaged or malfunctions, do not disassemble, repair or modify
the product arbitrarily. Request for assistance instead.
Do not move during operation.
Turn off both water and power supply if you need to move it. Do not pull the
power cord or plug by force. This may damage the product, cause electric
shock or fire.
Stop using the product when abnormal noise and odor occur.
In case of an earthquake, fire or flooding, stop using the product immediately
and remove the power plug from the power outlet.
If water leakage is obvious, immediately shut the water supply valve, disconnect
the power, and request for assistance.
Be careful not to leave the product unsupervised if you have children, or persons
with sensory or mental disabilities, or even with those who lack the knowledge
on how to use the product safely and correctly.
Never use without a cup.
Water may overflow from the drip tray.
When placing the cup on the drip tray, make sure the drip tray is fixed properly.
The water may overflow from the cup.
After replacing the filter, close the filter case tightly.
Do not apply excessive load or external shock to the product.
Damage due to severe shock may cause overheating or fire.
Do not spray insecticides or flammable liquid around the product.
It may cause product malfunction or fire.
B. Caution for Safety
Caution
Warning
for using
Caution
for using
on
installation

5
1. Do not install the product in the following places.
C. Caution for Installation
• Near fires
• Where there may be snow or rain
• Chemicals (volatile materials, organic solvents, etc.)
• Places where the temperature may fall below 0oC
2. Please use the following water quality range.
3. Do not connect hot water (above 38oC) to the product.
This may cause performance deterioration and failure.
4. Do not tilt more than 45owhen transporting the product.
Tilting it excessively may cause performance deterioration.
5. Do not operate the appliance without leveling.
It may cause malfunction or failure.
6. Do not install on inclined or unstable places.
This may cause performance deterioration, falls, and injury.
7. When connecting the tubing hose, do not allow the tubing hose
to be bent or pressed against heavy objects.
May cause malfunction.
8. When installing more than one product (water purifier, dishwasher,
etc.) and this product in one place, be sure to install raw water and
hoses separately for each product.
Every product has a different incoming water specifications.
• Water pressure: 1.4 ~ 7 kgf / cm2(137 ~ 686 kPa, 1.37 ~ 6.86 bar)
• Water temperature: 4 ~ 38 oC
• PH: 5.8 ~ 8.5
• Hardness: 300 ppm or less
• Turbidity: 0.5 NTU or less
• Water quality: Water quality that meets drinking standard
(Not available for uncertified drinking water quality standards and undetermined groundwater)
- Do not install in the low water pressure area below 1.4 kg /cm2
- Please consult with us when using in other water quality.
- If you do not use the water quality as specified above, the product warranty
becomes null and void.

D. Installation
6
Drawing (A)
Drawing (B)
Back view
Tri - way Socket
Faucet
Installation using Under Sink
1. Remove faucet & insert
the tri-way socket and
1/4” inlet ball valve.
See Drawing (A) here.
2. Connect the 1/4" PE
water tubing to the
1/4” inlet ball valve on
the one end, and to the
incoming water
connection on the
other end.
See Drawing (B) here.
1/4” Inlet Ball Valve
1/4” PE Water Pipe
1/4” Inlet Ball Valve
Water In
Connector
Inlet Water Pressure
Minimum : 10Psi/68,947 Pa
Maximum : 40Psi/275,790 Pa
Standard Installation of Tap
Diverter Valve
Connecting divertor to
ourside threads on faucet
Remove
Existing
Aerator
Swivel
Collar
Gasket
Adapter
Gasket
Adapter
Swivel
Collar
Handle
Handle
Faucet
adapters
(use size as needed)
Diverter valve
Diverter valve
1/4” PE
Water Pipe
please consult a
professional plumber

E. Name on Parts
7
Tray Drip
Power Plug Socket
Incoming Water Connection
Filter 2
Filter 1
Filter Case
Operation Panel
Water Faucet
Tray Grill
Filter socket

F. How to Use
8
If you have not used the water purifier for more than 2 days, please drain out
about 1 to 2 litres of water using any one of the dispensing buttons on the
operation panel.
Power Connection & Initialization Procedures
When the power supply is connected, the operation panel will
light up, and preparation for dispensing is completed.
• At initial startup, check for leaks between the product and water
tubing connections.
• To begin, press any of the dispensing buttons on the operation panel to
drain out about 2 ~ 3L of water before use. (Flushing operation)
• Flush the filter thorougly and do not worry about the initial noise in the
filters. The flushing will take care of the air that is trapped inside the filter.
This will not happen once the water purifier is initialized for operation.
Taking water (Pre-set amount of water for auto dispensing)
DuoGuardTM can dispense water in 150ml, 500ml and 1 liter.
• There may be an error in the amount of water being dispensed when the flow
rate of the raw water is too low (lower than 500ml/min).
• If you wish to interrupt/stop the water flow before it reaches the pre-set
amount, simply touch/press the button one more time and the water will
stop immediately.
1
2
To start dispensing water, simply press any button selection (1)
or (2), water will start to dispense from the faucet and it will stop
automatically.
• To dispense 500ml water, press button (1) once
• To dispense 1 liter of water, press and hold
button (1) for 2 seconds continuously.
• To dispense 150ml water, press button (2) once
The selected button will be lighted up with a continuous blink,
indicating the water is in a dispensing mode.

G. Caution for Use
9
1. This product is using 24V 0.6A.
2. Do not use several electrical appliances at the same time on one
power outlet.
• It may cause fire due to abnormal heat generation of outlet.
3. Never move the product while it is in operation.
• It causes the failure.
4. Do not leave the product at temperatures below freezing.
5. Do not use chemicals (volatile materials, organic solvents, etc.) on the
product, and keep it away from the product.
6. If water does not come out for a long time during use, check if the water
supply is shut off.
• In case the product is damaged, it is recommended to unplug
the product.
7. Remove the power plug before cleaning the inside of the product.
8. Do not use water directly from main water supply pipes.
• Water pressure can be too high and may damage the
product instantly.
9. If the product will not be used for a long time, shut off the water adapter
valve and pull out the power plug. At this time, do not touch the power
plug with your wet hands.
• There is a danger of electric shock or fire.
10. Since the filter of the water purifier is a consumable item, be sure to
change the filter on time to ensure clean drinking water.
• When using a filter that has exceeded its life, the water purifier
performance will be reduced.
11. Do not consume the water from the filter case for drinking or
other purposes.
12. If there is a strange sound, smell, or smoke that comes from the product
during use, immediately unplug the power cord, shut off the water
adapter valve, and call for assistance.

H. How to Clean
10
Exterior parts
●Use a dry cleaner or clean cloth to clean the main unit.
●Clean the intake parts with a clean cloth from time
to time.
●Wipe the inside and outside of the filter socket with a dry
cleaner or clean cloth.
●Remove the drip tray from the product and wash it with
running water.
●In case of heavy contamination of the drip tray, add
1 ~ 2 drops of neutral detergent and wash it.
●After washing with neutral detergent, rinse thoroughly
with tap water until no bubbles are removed.
●Be careful not to drop the drip tray or subject it to
external shocks during washing. Damage may cause
water leakage.
●Do not use hot water or alcohol when washing. It may
cause deformation or damage.
Tray drip
Filter socket

I. Hygienic Care of The Product
11
Install
Parts
Use
Set up
area
Faucet
Tray Drip
Check Self check
Managing Method
Recommended water conditions:
Please refer to Section C: C aution for Installation
Set up
Environment
Avoid:
● Outdoor / direct exposure to sunlight
● Close to the bath area / water splashes
● In front of the chiller / heater
Be careful not to splatter coffee, tea, sweet drinks, or
food ion the faucet. If it does, wipe it off immediately
and clean it with a non-woven cloth or cotton
swab once a week at the water outlet.
Do not put your hands or mouth directly to the
faucet. Also make sure that the cup you are using
does not touch the faucet water outlet.
If there is water, immediately discard it and wash it
once a week to prevent contamination.
If there is water, immediately discard it and wash it
once a week to prevent contamination.
Maintenance Filter
replacement
When replacing the filter, flush & discard water for
about 2 ~ 3 lliter before use. If no flushing is performed,
noise may occur due to air that is trapped inside the
filter when it is dry.
Be careful not to apply external shock to the filter
after installing the filter.

J. Filter Functions and Filter
Replacement Time
12
Filter function
Filter replacement time
PREMIUM FILTER (1)
NANO PRO (2)
1st stage
The 5 ㎛polypropylene filter media effectively removes
sediments like suspended solids, green debris, and particulate
contaminants larger than 5 ㎛.
2nd stage
Absorbs and removes chlorine, trihalomethanes (THMs), organic
chemicals and odor-causing substances dissolved in raw water
to provide fresh water taste.
3rd stage
Using positively charged magnetic nano-particles to capture
bacteria at ultra-low concentration. This is a rapid and highly
efficient way to capture viruses (noro-virus), bacteria (yellow
staphylococcus,E. coli, Salmonella, Shigella, Pseudomonas
aeruginosa) and parasites.
4th stage
Activated nano carbon powder is added between the layers to
enhance the removal of chemical disinfectants & detergents,
pesticides, acrylamide, benzene, carbon tetrachloride, vinyl
chloride and phenols.
• The replacement time of the filter, which is the specified consumable part of the product, is only an
estimated time, since filter replacement is largely dependent on the quality of the raw water, the
working pressure conditions, and the usage frequency and volume of water generated.
• You must change the filter at the appropriate time in order to enjoy clean drinking water.
• After replacing the filter, close the filter case tightly to avoid leaks.
Filter
(F1) PREMIUM (First carbon block filter)
(F2) NANO PRO (KX membrane filter)
6 months
6 months
Filter replacement period

▪When replacing, the number on the filter label must
match the number on the filter socket.
(E.g. filter label number 1- filter socket number 1 )
▪ Check that the ▲ position of the filter socket and the
reference point lock shape( ) of the filter are aligned.
▪Be careful not to change the positions of the two filters.
▪Please be careful not to use the same filter on both sides
K. How to Replace the Filters
13
Before installing the new filter, be sure to empty all the water inside the product
before replacing it.
1. Shut off the raw water adapter valve.
2. Press the water intake button to empty all filters
and water inside the product, and then unplug
the power plug.
3. Turn the filter case to the right to disassemble it,
and then turn the filter to the right to remove it.
4. Insert the filter to be replaced into the filter
socket and turn it to lock it.
5. Tighten the filter case by turning it to the left.
• Check if water leaks after supplying raw water. If a leak occurs,
immediately turn off the power, close the water supply valve, and
contact H2O LIFE SOURCE technical department.
6. After connecting the power plug, press the water intake
button to dispense water. Remember you MUST do flushing
of the new filter(s) for at least 1 to 2 litres of water.
1
2
2
1

14
Product name
Model name
DuoGuard
TM
JCP-K201
Rated voltage
24 V 0.6 A
Product size
261 W x 246 D x 305 H (mm)
Power consumption
10W
Monthly power consumption
1 kWH per month
Storage
Tankless
Weight
2.2 kg
Water Purifier
L. Product Specifications and
Water Flow Diagram
The above monthly power consumption is measured under normal use conditions (ambient temperature 25oC).
Therefore, the above values may change depending on the frequency of use.
Product specification
Water flow
Incoming
Water
Water
Intake
Pressure
Regulator
Solenoid
Valve
Flow Meter
Filter 1
Premium
Filter 2
Nano PRO
(Water amount measuring devise)

For more information, please contact our
H2O LIFE SOURCE office:
H2O LIFE SOURCE (SEA) PTE LTD
No 38 Jalan Pemimpin
#06-02 @ M38 Singapore 577178 SINGAPORE |MALAYSIA | PHILIPPINES |
MYANMAR | THAILAND | AUSTRALIA
www.h2olifesource.com
[phone] / 6655
WhatsApp
For more advanced technical support,
M. Troubleshooting
Symptom Need to check Yes No
No light on
switch area, &
not working
Check the
power plug.
How much time
you haven't used
the product?
Is it time for
filter replacement?
Check the tap
diverter connection
or any bend on
water tubing
Wait until it comes
Open the valve
Does source water
valve open?
Is it time for
filter replacement?
Is there any water
around the product?
Is the leak from
inside of product?
Put the power plug
with 24V 0.6A
Check if the power is on
& request for assistance
if something is wrong
Weird taste
Leakage
No water
coming out
Request for Assistance
Request for Assistance
Request for Assistance
Request a filter
replacement
Lock the adapter valve,
unplug the power plug
& request for assistance
Lock the adapter valve,
unplug the power plug
& request for assistance
Request for Assistance
Request for Assistance
Request for Assistance
Purchase a filter
replacement
Request a filter
replacement
Press the water intake
button and flush out
2 ~ 3L water before use