H3C SecPath T9000 IPS Series Operating and maintenance manual

H3C SecPath T9000
Intrusion Prevention System Series
Installation Quick Start
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: 5PW101-20170411

Copyright © 2015-2017, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of New H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,
SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage,
use, and disposal of this product must meet the applicable national laws and regulations.

i
Contents
Installation quick start ·················································································································································· 2
Preparing for installation ··················································································································································2
Installing the IPS ································································································································································2
Attaching the slide rails or rack shelf to the rack··································································································2
Installing cage nuts···················································································································································3
Attaching the cable management brackets to the IPS ··························································································4
Attaching the mounting brackets to the IPS ···········································································································6
Installing the IPS in the rack ····································································································································7
Grounding the IPS·····························································································································································8
Installing FRUs····································································································································································8
Attaching an ESD wrist strap ··································································································································8
Installing cards··························································································································································9
Installing power modules······································································································································ 10
Connecting an AC power cord ···································································································································· 11
Connecting a DC power cord ······································································································································ 12
(Optional.) Installing an XFP/SFP+/SFP/QSFP+ transceiver module······································································· 13
Logging in to the IPS ······················································································································································ 13
Obtaining documentation ············································································································································· 14
Index ···········································································································································································15

2
Installation quick start
This document provides a quick start guide for installing H3C SecPath T9000 Intrusion Prevention System
(IPS) Series. For detailed installation procedure, see H3C SecPath T9000 Intrusion Prevention System
Series Installation Guide.
Preparing for installation
If you are to install the IPS in a rack, make sure the following conditions are met:
•The rack is a standard 19-inch rack. For information about installing the rack, see the installation
guide for the rack.
•The rack is sturdy and reliably grounded.
•The rack has sufficient space for installing the IPS.
•No obstacles exist inside or around the rack.
•The total height of the devices you are to install in the rack is not higher than the available
installation height of the rack and enough clearance is reserved for cable routing.
•If you are to install multiple devices in the rack, place the heaviest device at the rack bottom.
Installing the IPS
IMPORTANT:
The IPS is heavy. H3C recommends that you install the IPS at the bottom of the rack.
The IPS is delivered without any filler panels in some card slots. The figures in this document are for
illustration only.
Attaching the slide rails or rack shelf to the rack
When you attach the slide rails or rack shelf to the rack, make sure the top flange of the slide rail or top
surface of the rack shelf aligns with the middle of the narrower metal area between holes, as shown
in Figure 1.
One rack unit (RU) has three holes, the middle of which is an auxiliary installation hole, and the other two
are standard installation holes. You can distinguish them by the space between each two holes. The
space between a standard installation hole and an auxiliary installation hole is wider than that between
two adjacent standard installation holes.

3
Figure 1 Locating the slide rail installation position
(1) Middle of the narrower metal area between holes
Installing cage nuts
1. As shown in Figure 2, align the bottom edge of the mounting bracket with the top flange of the
slide rail or the top surface of the rack shelf.
2. Mark the cage nut installation position on the front rack post. Each installation hole in the mounting
bracket corresponds to one cage nut installation position.
3. Install cage nuts on the marked square holes in the front rack post.
4. Perform the same steps to install cage nuts on another front rack post.

4
Figure 2 Installing cage nuts (T9006)
Attaching the cable management brackets to the IPS
The IPS uses signal cable management bracket and power cord management bracket to route the cables.
You need to install the signal cable management bracket separately for the T9010 IPS. All other T9000
IPSs come with the signal cable management brackets secured to the mounting brackets. You only need
to install the power cord management bracket for them.
•For the T9010 IPS, the signal cable management bracket installation position is at the upper part of
the chassis. The power cord management bracket installation position is at the lower part of the
chassis. The installation procedure is the same for the two brackets. See Figure 3.
•For the T9014 IPS, the power cord management bracket installation procedure is the same as the
T9010 IPS.
•The power cord management bracket of the T9006 IPS has a slightly different structure. See Figure
4for its installation.
To install a cable management bracket:
1. Unpack the cable management bracket.

5
2. Attach the cable management bracket to the chassis and align the screws with the mounting holes
in the chassis, as shown in Figure 3.
3. Fasten the screws.
Figure 3 Attaching cable management brackets to a T9010 IPS
(1) Attach the cable mana
g
ement bracket to the chassis
(2) Screw holes for installing the cable management bracket
(3) Screws for attachin
g
the cable mana
g
ement bracket to the chassis
(4) Si
g
nal cable mana
g
ement bracket (installed at the upper part of the chassis)
(5) Power cord management bracket (installed at the lower part of the chassis)
1
2
3
4
1
2
3
5

6
Figure 4 Attaching cable management brackets to a T9006 IPS
(1) Attach the cable mana
g
ement bracket to the chassis
(2) Screw holes for installing the cable management bracket
(3) Screws for attachin
g
the cable mana
g
ement bracket to the chassis
(4) Power cord mana
g
ement bracket (installed at the lower part of the chassis)
Attaching the mounting brackets to the IPS
Identify the left and right mounting brackets by their marks Land R. Attach the left and right mounting
brackets to the two sides of the IPS, as shown in Figure 5.
When you install the mounting brackets, face the front of the IPS.
Figure 5 Attaching the mounting brackets to a T9006 IPS
(1) Screws for attachin
g
the mountin
g
bracket to the chassis (2) Mountin
g
bracket
(3) Si
g
nal cable mana
g
ement bracket
1
2
3

7
Installing the IPS in the rack
CAUTION:
Do not use the fan tray handle, power module handle, filler panel handle, or air vents of the chassis to
carry the IPS. Any attempt to carry the IPS with these parts might cause equipment dama
g
e or even bodily
injury.
This task requires a minimum of two people.
To install the IPS in the rack:
1. Move the chassis to face the rear of the chassis towards the front of the rack.
2. Lift the IPS by using the handles of the chassis and place the IPS on the slide rails or rack shelf. Then,
slide the IPS along the slide rails into the rack until the mounting brackets on the IPS touch the front
rack posts.
The handle of the T9006 IPS is located at the top of chassis. The handles of the T9010 and T9014
IPSs are located at the two sides of the chassis.
3. Use the mounting screws provided with the chassis to secure the chassis to the rack.
If the mounting holes in the mounting brackets cannot align with the cage nuts on the rack, perform
the following tasks:
{Verify that the top flange of the slide rail or the top surface of the rack shelf aligns with the
middle of the narrower metal area between holes.
{Verify that the cage nuts are installed in the correct holes.
Figure 6 Installing the chassis in the rack (T9006)

8
Grounding the IPS
CAUTION:
•Correctly connecting the grounding cable is crucial to lightning protection and EMI protection. Before
you use the IPS, ground the IPS reliably.
•Use the (yellow-green double color) grounding cable provided with the IPS to ground the IPS.
•Connect the
g
roundin
g
cable to the earthin
g
system in the equipment room. Do not connect it to a fire
main or lightning rod.
To ground the IPS:
1. Unpack the grounding cable.
2. Remove the two grounding screws from the grounding point at the rear of the chassis.
3. Use the grounding screws to attach the two-hole grounding lug to the grounding point on the
chassis.
4. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding
terminal on the rack.
Figure 7 Grounding the IPS (T9006)
Installing FRUs
IMPORTANT:
Keep the packing boxes and other packing materials for the chassis and the FRUs secure for future use.
Attaching an ESD wrist strap
The IPS is provided with an ESD wrist strap. To minimize ESD damage to electronic components, wear the
ESD- wrist strap when installing FRUs.
To attach an ESD wrist strap:
1. Make sure the IPS is reliably grounded. For how to ground your IPS, see "Grounding the IPS."
2. Put on the wrist strap.
3. Tighten the wrist strap to keep good skin contact.