H3C S6800-2C-FC Operating and maintenance manual

Introduction to installation accessories
The installation tools are not provided with the switch. Prepare them yourself.
交换机不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
2
1
BOM: 3101A0MR
Tool list
H3C S6800-2C-FC Switch Installation Quick Start-6PW101
H3C S6800-2C-FC -6PW101
Attaching the accessories to the switch
Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good skin
contact and is reliably grounded. 操作者需佩戴防静电腕带，确保防静电腕带与皮肤良
好接触，并确认防静电腕带已经良好接地。
!
Phillipsscrewdriver
十字螺丝刀Marker
记号笔
ESDwriststrap
防静电腕带
Grounding cable and
grounding screw
接地线和接地螺钉
M6 screw and cage nut
(user supplied)
M6 螺钉和浮动螺母（请用户自备）
Mounting bracket
挂耳
Interface card filler panel
接口模块扩展卡假面板
Power module filler panel
电源假面板
Chassis rail and slide rail
滑道和导轨
M4 screw
M4螺钉
Removable cable tie
可拆卸式扎带
The installation positions of the accessories in the following figures are for illustration only.
Select installation positions for the accessories based on the installation requirements.
以下图中附件的安装位置仅供参考，请根据实际安装场景的需要选择合适的安装位置。
Multiple installation positions are available for the chassis rails on the chassis sides.
You can select an installation position for the chassis rails based on the chassis depth.
To maintain switch stability after installation, verify that the chassis rails reach out of
the slide rails.设备侧面板提供了多个滑道导轨安装位，用户可根据机柜的深度，调整滑
道导轨的安装位置；为保证设备安装后的稳定性，当滑道与滑道导轨安装完成后，请确
保滑道的头部露出滑道导轨。
Install the mounting brackets near the power module side 挂耳安装到靠近电源侧
Select a rack with a distance of 520 mm (20.47 in) to 769 mm (30.28 in) between the front
and rear rack posts.此安装方式适用于前后方孔条间距在520mm～769mm范围内的机柜。

3
Connect the grounding cable to the grounding point on the chassis side before installing
the switch in the rack.为了防止机箱安装到机柜后无法安装接地线，请您先将接地线安装
到交换机的侧面接地点上。
The switch provides a grounding sign and grounding screws at the primary grounding
point, but does not provide them at the auxiliary grounding point. 主接地点标有接地标
识，并带有接地螺钉，备用接地点无接地标识和接地螺钉。
The two grounding screws at the primary grounding point are also applicable to the
auxiliary grounding point. 主接地点上的两个接地螺钉同样适用于备用接地点。
Installing the switch in a 19-inch rack
19
Before installing cage nuts, mark their installation positions on the rack posts.
安装浮动螺母前，建议您先使用记号笔在机柜立柱上标注浮动螺母的安装位置。
Install the mounting brackets near the port side挂耳安装到靠近端口侧
Install cage nuts to the square holes on the rack
posts. 安装浮动螺母到机柜方孔条
Attach slide rails to the rack posts.
安装滑道到机柜
Mount the switch in the rack (twooptions) 安装交换机到机柜（二选一）
Install cage nuts and slide rails 安装浮动螺母与滑道
Connect the other end of the grounding cable to the grounding point on the rack
接地线另一端连接到机柜接地点
Power module side mounting
挂耳安装在靠近电源侧
1
2
1
2
2
1
4
2

Airflow through the switch
The switch provides front-to-back and back-to-front air aisles. Select fan trays to provide
airflow from the power module side to the port side, or from the port side to the power
module side based on the ventilation requirements at the installation site.
交换机采用前后风道设计，通过安装不同的风扇模块，可提供“电源侧到端口侧”和
“端口侧到电源侧”两种气流方向，满足不同环境下的散热要求。
Using the LSWM1HFANSC fan tray
采用LSWM1HFANSC风扇模块 Using the LSWM1HFANSCB fan tray 采用LSWM1HFANSCB 风扇模块
Connect the other end of the grounding
cable to the grounding point on the rack
接地线另一端连接到机柜接地点
Port side mounting
挂耳安装在靠近端口侧
The LSWM1HFANSC fan tray provides forward airflow from the power module side to
the port side. The LSWM1HFANSCB fan tray provides reverse airflow from the port
side to the power module side. LSWM1HFANSC为吹风风扇，电源侧进风，端口侧出
风；LSWM1HFANSCB为抽风风扇，端口侧进风，电源侧出风。
Before installing a fan tray, make sure the airflow direction marked on the fan tray meets
the ventilation requirements at the installation site. 安装风扇模块前，请根据风扇模块
的风向指示，确认气流方向和安装环境的通风要求一致。
Installing and removing a fan tray
Remove a fan tray
拆卸风扇
Install a fan tray
安装风扇
Install a filler panel in an empty power module slot to prevent dust from entering the
chassis and ensure good ventilation.
若电源模块插槽没有安装电源模块，请及时安装假面板，以保证设备的良好通风散热并
防止灰尘进入交换机。
The switch comes with the fan tray slots empty. You must install two fan trays of the
same model for the switch for adequate heat dissipation. Do not power on the switch
when no fan tray is installed.交换机出厂时两个风扇插槽均为空，为保证设备的正常散
热，用户必须安装两个相同型号的风扇模块，否则禁止交换机上电运行。
If both fan trays fail when the device is operating, finish replacing the fan trays within
2 minutes.设备运行过程中，如果两个风扇模块均出现故障，则必须在2分钟内完成故
障风扇模块的更换。
If one fan tray fails when the switch is operating and the ambient temperature is not
higher than 27°C (80.6°F), replace the fan tray within 24 hours, and make sure the
faulty fan tray is in position before replacing it. If the ambient temperature is higher
than 27°C (80.6°F), replace the fan tray immediately.设备运行过程中，如果一个风扇
模块出现故障，则当环境温度不高于27°C时，必须在24小时内完成故障风扇模块的更
换，且更换前需保持故障风扇模块在位；当环境温度高于27°C时，请立即进行更换。
Make sure each hot swappable module slot is installed with a module or filler panel
when the switch is operating. 设备运行过程中，必须确保所有可插拔模块插槽不能为
空，请务必安装相应的模块或假面板。
!
Install a power module 安装电源模块 Remove a power module 拆卸电源模块
1
2
1
21
2
2
1
5
6
2
1
2

Copyright © 2017, New H3C Technologies Co., Ltd.
For more information about the product and installation procedures, log in to www.h3c.com.hk
Copyright © 2017 新华三技术有限公司 版权所有，保留一切权利。
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com
7
To access the most up-to-date H3C product documentation on the H3C website at
www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Choose the desired product category and model.
您可以访问H3C网站（www.h3c.com）获取最新的产品配套资料：
1. 请访问网址：http://www.h3c.com/cn/Technical_Documents；
2. 选择产品类别和产品型号，即可查询和下载与该产品相关的手册。
Obtaining documentation
Install a filler panel 安装假面板 Remove a filler panel 拆卸假面板
Connect the DC power cord
连接直流电源线 Connect the AC power cord 连接交流电源线
Use a removable cable tie to secure the power cord. The method for securing AC
and DC power cords are the same. The following figure uses the AC power cord
as an example. 使用可拆卸式扎带固定电源线，以防止电源线脱落；直流电源线
和交流电源线的固定方式相同，此处以交流电源线为例介绍电源线的固定过程。
Installing and removing an interface card
Do not touch the electronic components on an interface card to avoid damage.
请勿直接接触接口模块扩展卡上的元器件，避免造成损坏。
Install a filler panel in an empty interface card slot to prevent dust from entering the
chassis and ensure good ventilation.若接口模块扩展卡插槽没有安装接口模块扩展卡，
请及时安装假面板，以保证设备的良好通风散热并防止灰尘进入交换机。
!
Before connecting the power cord, connect the grounding cable and make sure the
switch is reliably grounded.在连接电源线前，您需要先连接接地线，保证交换机正确接地。
Connect the power cord to the switch first and then to the power source to avoid bodily
injury. 连接电源线时，请先完成电源线与交换机侧的连接，再进行电源线与供电系统的连
接，以免造成人身伤害。
!
Connecting the power cord
12
Remove a filler panel
拆卸假面板
Install a filler panel
安装假面板
To remove a filler panel:
1. Use your thumb and forefinger to hold the filler panel through the two holes.
2. Push right the metal tab in the left hole and pull out the filler panel along the guide rails.
拆卸假面板时，请您用食指和拇指扣住假面板上的两个圆孔，向右用力按压左边圆孔内的金
属弹片，然后沿插槽导轨向外拉出假面板。
Install an interface card
安装接口模块扩展卡 Remove an interface card 拆卸接口模块扩展卡
2
1
1
2
23
1