H3C S7500X Series User manual

1
BOM: 3104A0KJ
H3C S7500X Switch Series Installation Quick Start-6PW103
H3C S7500X系列交换机 快速安装指南-6PW103
2
Flat-blade screwdriver
一字螺丝刀
Phillips screwdriver
十字螺丝刀
Needle-nose pliers
尖嘴钳
Wire-stripping pliers
剥线钳
Diagonal pliers
斜口钳
Claw hammer
羊角锤
Marker
记号笔
Tool list
This document provides a brief guide for installing H3C S7500X switch series. For more installation
information, see H3C S7500X Switch Series Installation Guide.
本文档用于为H3C S7500X系列交换机的硬件安装提供简明快捷的操作指导，关于安装过程及注意事项更
全面、完整的介绍，请您参见《H3C S7500X系列交换机安装指导》。
The figures in this document are for illustration only.
设备及各模块外观请以实际发货为准，本文中的图片仅供参考。
The instalLation procedure is similar for S7500X switches. The following uses an S7506X switch as an
example unless otherwise specified.
S7500X系列交换机各模块安装步骤类似，如无特殊说明，均以S7506X为例。
Safety recommendations
To avoid equipment damage or bodily injury, read the following safety recommendations before installation.
Note that the recommendations do not cover every possible hazardous condition.
为了避免在安装交换机过程中对人和设备造成伤害，请您在安装前仔细阅读本节的安全建议。
实际情况中包括但不限于以下安全注意事项：
To prevent ESD damage, always wear an ESD wrist strap and make sure it is reliably grounded before
you touch the switch, cards, or PCB.
为防止人体静电损坏敏感元器件，请您在接触设备、单板、IC芯片等之前佩戴防静电腕带，并将防静电腕
带的另一端良好接地。
Do not install the switch, FRUs, or cables when the switch is powered on.
禁止带电安装设备、模块和线缆。
To avoid equipment damage or bodily injury, make sure the switch is reliably grounded before powering
on the switch.
请确保设备接地后再接通电源，以免危及人身和设备安全。
!
Prepare the following installation tools yourself as required.
请您根据实际安装需求自己准备安装工具。
Installation accessories
ESD wrist strap
防静电腕带
Grounding cable
接地线
Removable
cable tie
可拆卸式扎带
M4 countersunk-
head screw
M4沉头螺钉
Mounting brackets
挂耳
Console cable
配置口电缆
M6 screw
M6 螺钉
M3 countersunk-
head screw
M3沉头螺钉
Floating nut
浮动螺母
Attaching cage nuts to the rack 安装浮动螺母到机柜
Installing the switch
1. Determine the cage nut installation holes
based on the mounting bracket and slide rail
installation positions.
2. Mark the cage nut installation holes.
3. Install cage nuts.
Cable management
bracket
走线架
1. 根据挂耳孔位及滑道的安装位置确定浮动螺母的
安装孔位。
2. 用记号笔在方孔条上标出浮动螺母的安装孔位。
3. 在对应位置安装浮动螺母组件。
This section only lists the most commonly used installation accessories.
本节介绍了安装过程中最常用的安装附件。
2
1
1
1
1
3

4
Installing the cable management bracket
安装走线架
Installing mounting brackets
安装挂耳
Attach the cable management bracket to the
left mounting bracket, which has installation
holes for the cable management bracket.
将走线架安装到带有走线架安装螺孔的左挂
耳上。
3
Installing FRUs 安装模块
Installing cards 安装单板
1
23
4
1
1
2
2
Installing power modules 安装电源模块
For dual-grid input, the input voltage, phase, and frequency for the two grids must be the same.
双电网输入时，输入电压的幅值和频率需要保持一致。
To use two power modules, provide a circuit breaker for each power module.
双电源供电时，每个电源必须单独配一个断路器。
Do not install a power module adapter and a 3RU module on the same switch. Make sure the two power
module slots have the same power modules and power modules adapters.
不同型号电源模块不能混插，且电源适配器和3RU电源模块不能混插。
To avoid power module damage or bodIly injury, move a power module by supporting its bottom instead
of holding its handle.
搬运电源模块时，请您用手托住模块的底部，切勿提着模块拉手进行搬运，以免损坏电源模块甚至伤害您
的身体。
!
Do not try to move the chassis by holding an FRU handle, air vents of chassis, oR the handle on the rear.
Any attempt to carry the switch with these parts might cause equipment damage or even bodily injury.
请勿试图通过抓握设备模块（风扇框、电源）把手、机箱通风孔或机箱后面板拉手来进行设备的搬运，否
则可能因该部件无法承重而引起设备损坏，甚至会伤害到您的身体。
After placing the switch on the slide rails, do not leave go of your hands immediately because this might
tip the switch. Tipping the switch might cause switch damage and even bodily injury.
将机箱放至滑道后，请确保机箱放置平稳后再松手，以免机箱倾倒而损坏设备，甚至伤害您的身体。
!
Use a minimum of two people to move the switch. For heavy models, use a mechanical lift as a best practice.
要求多人配合（不少于2人）搬运设备，对于较重机型， 推荐您使用机械设备搬运。
!Before installing a card in the chassis, make sure the connectors on the card are not broken or blocked.
安装前，请检查单板的连接器是否有破损和堵塞，以免对机箱背板造成损坏。
1
2
3
To ensure the grounding effect, use the yellow-
green grounding cable provided with the switch
to ground the switch.
为了保证良好的接地效果，请使用随机附带的接
地线（黄绿双色保护接地电缆）。
Connect the grounding cable to the grounding
system in the equipment room. Do not connect it
to a fire main or lightning rod.
消防水管和建筑物的避雷针接地都不是正确的接
地位置，交换机的接地线应该连接到机房的工程
接地。
!
Grounding the switch 交换机接地
1
22
Installing the switch in a rack 安装交换机到机柜

5
Connecting power cords 连接电源线
1
2
2
Connecting the power cord for a PSR320-A/
PSR650-A power module
连接PSR320-A/PSR650-A电源线
1
2
3
45
10A
6
Connecting the power cord for a PSR650C-12A/PSR1200-
A/PSR1400-A/PSR2800-ACV power module
连接PSR650C-12A/PSR1200-A/PSR1400-A/PSR2800-ACV电源线
10A
1
2
3
4
The PSR650C-12A power module uses a 10A AC power
cord. The PSR1200-A/PSR1400-A/PSR2800-ACV uses a
16A AC power cord. The power cord connection procedure
is similar for the two power modules.
This procedure uses the PSR650C-12A as an example.
PSR650C-12A电源模块使用10A交流电源线，
PSR1200-A/PSR1400-A/PSR2800-
ACV电源模块使用16A交流电源线，电源线连接方法
类似，本节以连接PSR650C-12A电源线为例。
To use a power module adapter, first install the power module adapter in the chassis, and then install power
modules in the adapter. The installation procedure is similar for power modules and power module adapters.
有的电源模块必须配合电源模块适配器使用，在安装电源模块前请先安装电源适配器，电源模块适配器与电源
模块的安装方法类似。
Before connecting an AC power cord, make sure the circuit breaker at the power source end is turned off.
连接交流电源线前，请您确保连接电源线的输入端空气开关置于断开状态。
Before connecting a DC power cord, make sure the circuit breakers for the positive (+) and negative (–)
terminals at the power source end are switched off.
连接直流电源线时，请您确保电源输入端的断路器处于完全断开状态(+、-两路均已断开)。
!
!The accessories provided with the power module are different in batches. If a releasable cable tie is
provided with the power module, follow this procedure to connect and secure the power cord.
不同批次的PSR1400-A和PSR2800-ACV电源附件不同。若电源附件中包含可拆卸式扎带，请参考此方式连接
和固定电源线。
16A
Using a 16A AC power cord
使用16A交流电源线
The PSR2500-12AHD power module uses a 16A AC power cord or a high-voltage DC power cord.
PSR2500-12AHD电源模块使用16A交流电源线或者高压直流电源线。
Using a high-voltage DC power cord
使用高压直流电源线
+ or N
-orL
PE
Ground
DC power source
Positive terminal (+)
Negative terminal (-)
PGND terminal
Connecting the power cord for a PSR2500-12AHD power module
连接PSR2500-12AHD
Connecting the power cord for a PSR6000-ACV power module
连接PSR6000-ACV电源线
Connecting the power cord for a PSR1400-A/PSR2800-ACV power module
连接PSR1400-A/PSR2800-ACV电源线
!If a power cord retention clip is provided with the power module, follow this procedure to connect and secure
the power cord.
不同批次的PSR1400-A和PSR2800-ACV电源附件不同。若电源模块包含电源线防脱套件，请参考以下方式连接
和固定电源线。
16A
1
2
34
5
6
16A
2
3
1

Powering on the switch and verifying its operation 交换机上电并检查
Make sure the power cords are connected correctly and the power source is operating correctly. Then power on
the switch. Verify that the switch is operating correctly by observing the LEDs on the switch. For more information
about the LEDs, see H3C S7500X Switch Series Installation Guide.
确认电源线已经正确连接到外部供电系统且供电系统已正常供电，使设备上电。请您根据设备各部件的指示灯正常
状态来检查设备是否正常。关于设备指示灯状态的详细描述，请您参见《H3C S7500X系列交换机 安装指导》中的
“附录C 产品指示灯介绍”。
7
USB console port
USB Console接口
Console port
Console接口
Connecting the power cord for a PSR1200-D power module
连接PSR1200-D电源线
Connecting the power cord for a PSR320-D/PSR650-D/PSR650C-12D power module
连接PSR320-D/PSR650-D/PSR650C-12D电源线
3
2
1
45
1
2
3
Connecting the power cord for a PSR1400-D/PSR1400-12D1/PSR2500-12D power module
连接PSR1400-D/PSR1400-12D1/PSR2500-12D电源线
To access the switch for the first time, use a console cable to connect the console port or USB console port
on the switch. If you connect both the console port and USB console port, only the USB console port is
available.
当您首次登录设备时，只能通过Console口/USB Console口登录。如果Console口和USB Console口同时连
接电缆，仅USB Console口可以正常通信。
Connecting the console cable 配置电缆连接
Accessing the switch
1
2
35
6
4
Copyright © 2016-2021, New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
Copyright © 2016-2021 新华三技术有限公司 版权所有，保留一切权利。
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com