Habitat Vince User manual

Assembly Instructions - Please keep for future reference VINC-3SB-SS14-A
1 2 1
Tools required
Width - 180cm
Depth - 45cm
Height - 75cm
Dimensions
Important - Please read these instructions before assembly
If you need help or have damaged or missing parts, email:
customerser[email protected].uk or call: 0344 499 4686
Vince Sideboard 3 Door
30

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on the
front cover and pages 2.
Remove all fittings from the plastic
bags and separate them into their
groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough space
to layout the parts before starting.
Do not stand or put weight on the
product, this could cause damage.
Assemble the item as close to its
final position (in the same room) as
possible.
Do not place furniture directly in
front of radiators, fires or any other
source of heat.
Parts of the assembly
will be easier with 2
people.
Assemble on a soft level surface
to avoid damaging the unit or your
floor.
We do not
recommend the
use of power drill/
drivers for inserting
screws, as this could
damage the unit. Only use hand
screwdrivers.
Dispose of all packaging carefully
and responsibly.
The individual wood slats in your
piece of furniture are specially
selected and sorted by hand by
skilled craftsmen. They follow
specific guidelines securing the
quality demands and design
preferences that lay out the form
of this furniture range.
General care and maintenance
If for any reason you should have
problems with your Habitat product,
please contact the store from which
you purchased it.
Please retain your receipt as proof of
purchase.
If you have anycomments or
suggestions regarding this product,
assembly instructions or service
received, please contact the store or
Habitat Head Office via its web site:
www.habitat.co.uk
or write directly to: Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW
General information
1 2
Wood is a living material, affected by
temperature and moisture for a
long period after you start using it.
Thereby, table tops and top plates
will expand and shrink according to
the seasons, and tiny cracks in the
wood that may occur, are some of
the joys of owning a natural product.
Your piece of furniture comes pre-oiled
from the factory but should be re-oiled
regularly to keep it in good order.
Please see re-oiling instructions below.
Legs for coffee and dining tables should
be checked occasionally to ensure they
are fully tightened in place.
Avoid extreme humidity and heat.
Do not place the item close to heat
sources
Clean the surface with a clean,
wrung out cloth. Never use
detergents
Cleaning and care of oiled and lacquered surfaces
Coloured stains like red wine must
be dried off immediately
Smaller stains and marks can be
polished off the oil surfaces of your
furniture (excluding any lacquered
surfaces) with sand paper no 220 or 180
Re-oiling the oiled surfaces of your furniture (excludes lacquered surfaces)
To keep your furniture it in good
order we suggest re-oiling it every 3
to 6 months.
Danish furniture oil can be bought
at any good hardware store (such as
Homebase).
Apply plenty of oil with a clean cloth.
Table tops must be treated
underneath as well as on the top side.
(Be careful that the oil doesn’t drip
onto your floor!)
After 15 minutes, polish with a s
andpaper sponge or fine sandpaper
(no. 150) along the grains of the wood
Polish off remaining oil with a clean,
dry cloth
Do not use the item, until the oil is
completely absorbed

2
BC Note: There are ‘Batch Code’ labels where shown on the indicated items, these should beretained.
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, email:
customerser[email protected].uk or call: 0344 499 4686
1 of 1
1. Cabinet
2.
Leg
x 4
BC

Components - Fittings
Please check you have all the fixing listed below
If you need help or have damaged or missing parts, email:
customerser[email protected].uk or call: 0344 499 4686
Note:
A
Ruler - To help correctly identify the fixings
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120
105
The quantities below are the correct amount to complete the assembly. In some
case more fitting maybe supplied than are required.
3
Nylon strap x 2
B
Wall brackets x 4
C
20mm Screws x 4

Assembly Instructions
Step 1
1 2 1
Please Take Care When Turning Upright.
4
x 4

Assembly Instructions
Step 2
1 2 1
5
Anti-Tip Restraint Assembly is REQUIRED in order to complete construction of this product.
When properly installed, this hardware can provide protection against the unexpected tipping
of furniture
IMPORTANT!
For your safety this product must be secured to a wall using the provided anti-topple wall straps. Please use the
correct type of fixings for attaching the wall strap to your wall. Sorry we could not provide these fixings due to the
variety of different types of wall you might have.
Please refer to the Wall Mounting and Fixings on the last page of this instruction for more information.

Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug Heavy
loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty” wall
plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can be
used.
For use with heavier loads such as TV &
HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when fitting or supporting heavy
loads such as shelving, wall cabinets and
coat racks.
For use with walls stuck with plasterboard.
The hammer fixing allows it to be fixed
to the wall rather than the plasterboard.
Always check the fixing is secure to the
retaining wall.
For use when attaching light loads on to
plasterboard partitions.
Safety: Always check the fitting and
location to ensure your safety in and
around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
Important: When drilling into walls always
of brick, breeze block, concrete, stone or wood.
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic tiles.
Ensure wall plugs are inserted beyond the thickness of the ceramic
tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Wall Fixings: Make sure that the screws and wall plugs being used are suitable
for supporting your unit. Consult a qualified tradesperson if you are
unsure.
- because of the variety of
different wall types, Habitat
cannot provide you with the
exact fixings you will need to
fix this product to the wall.
You must first identify the
type of wall you intend to fix
product onto and then contact
your local hardware store to
get the appropriate fixings.
A Guide to - Wall Mounting & Fixings