Habitat Haxby 3120695 Manual

Care & Instruction Manual
Habitat Haxby illuminated bathroom mirror

Black/Blue - Neutral
Red/Brown - Live
Ensure electrical connections are tight and no loose strands of wire are left out of the terminal block.
 If in any doubt about the type of wiring you have available or the location of
your mirror please consult a qualified electrician.
This fitting is IP44 rated therefore suitable for installation in bathrooms as defined by the I.E.E.
Wiring Regulations. IP44 fittings are splashproof, suitable for Zones 1 & 2 except where likely to come in to direct
contact with water jets. An example of exceptions would be in a shower cubical or an area where water jets are
used for cleaning purposes.
It is recommended all bathroom appliances be protected by a 30mA RCD Circuit Breaker.
Please use the Guide below to ensure the correct positioning of your luminaire.
ZONE 2
60cm radius
from tap
ZONE 0
225cm
ZONE 1 ZONE 2
60cm 240cm
Important: Ensure the house electricity supply is off at the fuse board. Ensure other
persons cannot restore the electricity supply without your knowledge.
Before removing the existing fitting, carefully note the position of each set of cables. If
there are loops in cables that are not connected to the light, these must be terminated in a
separate terminal block not connected to the fitting.
Instruction to use
.
wall

Step 1
Step 2
Step 3
Touch on/off Switch
75MM

You should now recycle your waste electrical goods and in doing so help
the environment. This symbol means an electrical product should not be
disposed of with normal household waste. Please ensure it is taken to a
suitable facility for disposal.
Visit www.recycle-more.co.uk, click on “bank locator” and enter your
postcode to find your nearest recycling site.
For your safety, this product must be installed in accordance with local Building Regulations.
If in any doubt, or wher required by the law, consult a competant person who is registered with an electrical self-
certification scheme. Further information is available online or from your Local Authority.
To prevent electrocution, switch off at the mains supply before installing or maintaining this fitting. Ensure other
persons cannot restore the elctricity supply without your knowledge.
To avoid damage to concealed wiring dring instalation, establish the direction of the supply cable before drilling
fixing holes.
This fitting is a Class II appliance.
Maximum Voltage 220-240V AC 50~60Hz
Integrated LED-bulbs cannot be replaced.
Ensure that ALL electrical connections are tight with no loose strands.
This luminaires is designed for indoor use only.
Before commencing installation or maintenance, ensure electricity is switched off at the mains.
This luminaire is suitable to be mounted on a Normally Flammable Surface e.g. a material based on wood. This
item contains glass - use care when handling to avoid damage or injury.
Important:
This luminaire apply touch on/off switch.
Made in China for Habitat. Argos Limited, 489-499 Avebury Boulevard,
Milton Keynes, MK9 2NW. Argos (N.I.) Ltd, Forestside Shopping Centre,
Upper Galwally, Belfast, United Kingdom, BT8 6FX.
Argos Distributors (Ireland) Limited, Unit 7, Ashbourne Retail Park,
Ballybin Road, Ashbourne, County Meath, Ireland.
We care about quality and what you think,
If you have any comments, good and bad,
please call our Careline:0345 640 2020
or visit www.habitat.co.uk
Your statutory rights are not affected.

No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board.The hammer fixing allows it to
be fixed to the wall rather than the plaster
board.Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Wall Mounting & Fixings
A Guide to