Hadex SPA-8100 User manual

SPA-8100 / 8102 Fixed Voltage
Switching Mode Power Supply
USER’S MANUAL
INTRODUCTION
This fixed voltage switching mode power supply is designed with high RFI stability especially for DC operated radio
equipment. It is also suitable for a variety of applications that need a clean DC source.
The concealed trimmer allows fine tuning of output voltage range of 13.3 ~ 14.5V for SPA-8100 & 26.6 ~ 29V for SPA-
8102.
Constant current circuitry is used for overload , short circuit and over temperature protection. Output voltage and current
would drop to a safety value when any of the faults occur and the indicator will light up in red. This power supply also has Over
Voltage Protection to prevent your connected equipment from damage by abnormal high output voltage.
Please read through this manual and pay special attention to the caution and safety precautions.
Keep this manual in an easy to find place for future reference.
CAUTIONS
DO NOT use this power supply for high inductive load such as solenoid or motorized equipment because of the inductive kick
back from the output may damage the power supply.
DO NOT operate power supply immediately with a newly replaced fuse before the fault has been found and rectified. Make
sure to use the same rating and type as the original fuse.
SAFETY PRECAUTIONS
Never remove the casing when the power supply is connected to AC or load.
Never touch the unit when your hands are wet.
Never block any of the grille openings or allow foreign object to get inside .
Must use a mains AC 3 pin socket with effective grounding.
PANEL DESCRIPTION
1. On/Off Switch with Light 2. Indicator (Green : Operate / Red : Overload)
3. Cigar Socket with center positive ( 10A Max. ) 4. Main DC Output Binding Post
5. AC Power Input Connector 6. Cover Fuse Holder
7. Fine tune access port at the base plate. (Range : 13.3-14.5V for SPA-8100 & 26.6 ~ 29V for SPA-8102)

INSTALLATION
1. This power supply is designed for indoor use only , put the unit in a well ventilated place and allow at least 50mm(2 in.)
space on two sides.
2. Check for the correct input AC voltage with the rating label on the power supply
Make sure your mains plug is of 3 pin version and the ground pin is effective as the grounding of the power supply will
prevent electrical shock caused by leakage.
3. Turn on the power supply for a few minutes , the power switch(1) should be lit and the indicator (2) should be in green.
4. Turn off the power supply and connect the equipment with correct polarity.
5. Turn on the power supply first , then turn on the equipment .
6. When the operation is finished, turn off the equipment first , then turn off the power supply.
FINE TUNING THE OUTPUT VOLTAGE (13.3 ~14.5V for SPA-8100 & 26.6 ~ 29V for SPA-8102 )
This regulated power supply has been factory preset at a stable DC output.
Rarely you need to do any fine tuning under normal operation .
However , should the need for specific precise output voltage other than the preset voltage is required , refer to the following
procedure.
1. Let the power supply warm up for about 15 min.
2. Turn the power supply over with the bottom up and connect a digital multi-meter(DMM) with at least 2 decimal read out to
the main output terminal (4).
3. Locate the fine tune access hole (8) on the bottom as shown in Fig.1.
4. Insert a slim flat head screw driver to get to the trimmer as shown in Fig.1.
5. Carefully and slowly turn the screw driver clockwise or anti-clockwise while keeping an eye on the DMM for your desired
voltage setting.
6. Measure again the output voltage to re-confirm your new setting after returning the power supply to its normal operation
position.
SPECIFICATIONS
SPA - 8100 SPA - 8102
OUTPUT VOLTAGE: Fixed 13.8Vdc +/-0.5V Fixed 27.6Vdc +/-0.5V
OUTPUT CURRENT:
Main Output Post 10A Continuous , 12A Max.
(1 min. 50% duty cycle)
5A Continuous , 6A Max.
(1 min. 50% duty cycle)
Main Output Post + Cigar Socket 10A Continuous , 12A Max.
(1 min. 50% duty cycle)
5A Continuous , 6A Max.
(1 min. 50% duty cycle)
RIPPLE AND NOISE: ≤50mVp-p, 5mVr.m.s,
LINE REGULATION: ≤50mV (±10% Variation)
LOAD REGULATION: ≤100mV (0~100% Load)
POWER SOURCE: 230Vac/50Hz~ (or On Request)
COOLING SYSTEM Air Convection
DIMENSION (W×H×D): 181 ×63 ×190 (mm) / 7.1 x 2.5 x 7.5 inch
WEIGHT: Approx. 1.55Kg / Approx. 3.4Lbs.
Rev1.0 07/2005 7673-8100-0000
Buttom View
Fig.1