Haibrain PROGUARD 800 Series User manual

PROGUARD
800
PROGUARD 800 SERIES
INSTALLATION MANUAL
NETHERLANDS
20205 / 20100607 • PROGUARD800TM ©
ALL RIGHTS RESERVED HAIBRAIN ®

Safety Warnings
• The wiring of your electrical installation is live (230 V) and extremely dangerous. Never
connect the module when plugged into the mains. Always turn off the main switch before
starting the installation.
• This product is for professional use and should be installed by a certified installer.
• To prevent short circuits, this product should only be used inside and only in dry spaces. Do
not expose the components to rain or moisture. Do not use the product close to a bath,
swimming pool etc.
• Do not expose the components of your systems to extremely high temperatures or bright
light sources.
• In case of improper usage or if you have altered and repaired the product yourself, all
guarantees expire. Haibrain does not accept responsibility in the case of improper usage of
the product or when the product is used for purposes other than specified. Haibrain does not
accept responsibility for additional damage other than covered by the legal product
responsibility.
• This product is not a toy. Keep out of reach of children.
• Keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never
use old and new batteries or different types of batteries together. Remove the batteries when
you are not using the system for a longer period of time. Check the polarity (+/-) of the
batteries when inserting them in the product. Wrong positioning can cause an explosion.
• Only connect the adapter to the mains after checking whether the mains voltage is the same
as the values on the identification tags. Never connect an adapter or power cord when it is
damaged. In that case, contact your supplier.
• Automatic switching devices provide comfort, but can also be dangerous. They can surprise
people or can ignite clothing hanging over an electric heat source. Please be careful and take
appropriate measures to avoid accidents.
-2- ©HAIBRAIN

Table of Contents
Safety Warnings ......................................................................................................................................2
Table of Contents ....................................................................................................................................3
Chapter One: Introduction .......................................................................................................................6
1.1: Documentation Conventions ......................................................................................................6
1.2: Specifications .............................................................................................................................7
1.3: System Overview .......................................................................................................................7
1.4: Hardware Layout........................................................................................................................9
Chapter Two: System Installation..........................................................................................................13
2.1: Pre-Installation Planning ..........................................................................................................13
2.2: Installation Procedure ..............................................................................................................14
2.3: Back Tamper............................................................................................................................17
2.4: Installing HK855 Hardwire LCD Keypads ................................................................................17
Chapter Three: Basic System Operation...............................................................................................19
3.1: Front Panel Layout...................................................................................................................19
3.2: System Status LEDs ................................................................................................................19
3.3: Front Panel Keypad .................................................................................................................20
3.4: LCD Display .............................................................................................................................20
3.5: Vocal Message Annunciation...................................................................................................21
3.6: HK855 Hardwire LCD Keypad..................................................................................................22
3.7: Arming/Disarming.....................................................................................................................23
3.8: Remote Arming/Disarming via SMS.........................................................................................25
3.9: Remote Arming/Disarming via DTMF ......................................................................................26
3.10: LCD Keypad Alarm Activation................................................................................................26
Chapter Four: Advanced System Operation..........................................................................................28
4.1: Menu Navigation ......................................................................................................................28
4.2: Stop Communications ..............................................................................................................28
4.3: Sensor Bypassing/Unbypassing ..............................................................................................29
4.4: User Codes ..............................................................................................................................29
4.5: Follow Me.................................................................................................................................31
4.6: Event Log .................................................................................................................................31
4.7: Service Menu ...........................................................................................................................32
Chapter Five: Telecontrol and Two-Way Audio .....................................................................................37
5.1: Incoming Calls..........................................................................................................................37
5.2: Outgoing Calls..........................................................................................................................39
Chapter Six: X-10 Home Automation Control ........................................................................................42
6.1: Keypad Control ........................................................................................................................42
6.2: Keyfob Control .........................................................................................................................42
6.3: Telephone Control....................................................................................................................42
6.4: Scheduling ...............................................................................................................................43
Chapter Seven: Devices........................................................................................................................45
7.1: Device Registration ..................................................................................................................45
7.2: Device Descriptors ...................................................................................................................45
7.3: Device Deletion ........................................................................................................................45
7.4: Supervision Time .....................................................................................................................46
7.5: Re-Synchronization..................................................................................................................46
7.6: Zones .......................................................................................................................................46
7.7: Keyfobs ....................................................................................................................................49
7.8: Keypads ...................................................................................................................................50
7.9: Repeaters.................................................................................................................................51
7.10: Wireless Siren ........................................................................................................................51
7.11: Smartkeys (for future use)......................................................................................................52
Chapter Eight: Entry/Exit Timers and System Tones ............................................................................53
8.1: Entry/Exit Delay........................................................................................................................53
8.2: Arm on Exit...............................................................................................................................53
8.3: Supplementary Entry Delay......................................................................................................53
ProGuard800™ -3-
8.4: Entry Deviation.........................................................................................................................54

8.5: Exit Restart...............................................................................................................................54
8.6: Arming Tones...........................................................................................................................54
8.7: Home Automation Tones .........................................................................................................55
8.8: System Trouble Tones .............................................................................................................55
8.9: Tones Options..........................................................................................................................56
Chapter Nine: System Options ..............................................................................................................57
9.1: Swinger Setting ........................................................................................................................57
9.2: Code Lockout ...........................................................................................................................57
9.3: Arm/Disarm Options.................................................................................................................57
9.4: Panic Alarm..............................................................................................................................59
9.5: AC Loss Delay .........................................................................................................................59
9.6: Display Options ........................................................................................................................60
9.7: PGM Output Options................................................................................................................61
9.8: Guard Code (for future use) .....................................................................................................62
9.9: “No Arm” Indication ..................................................................................................................62
9.10: Jamming Detection ................................................................................................................62
9.11: “No Motion” Time ...................................................................................................................63
9.12: Microphone/Speaker Options.................................................................................................63
9.13: Vocal Messages.....................................................................................................................63
9.14: Installer Access ......................................................................................................................63
9.15: Auto Log View (for future use) ...............................................................................................63
9.16: Daylight Savings ....................................................................................................................64
9.17: Report Fail Trouble ................................................................................................................64
9.18: Cancel Alarm..........................................................................................................................64
9.19: Cross Zoning (for future use) .................................................................................................65
9.20: Verified Fire............................................................................................................................65
9.21: Battery Type ...........................................................................................................................65
Chapter Ten: Communications ..............................................................................................................66
10.1: Monitoring station Reporting ..................................................................................................66
10.2: General Options for Monitoring station Reporting..................................................................67
10.3: Vocal Message Dialler ...........................................................................................................68
10.4: Remote Programming ............................................................................................................70
10.5: Service Call ............................................................................................................................72
10.6: Communications Options .......................................................................................................72
10.7: GSM Options..........................................................................................................................75
10.8: TWA Event Report Options....................................................................................................76
10.9: Event Options for Monitoring station Reporting .....................................................................77
10.10: Vocal Message Dialler Event Options..................................................................................78
Chapter Eleven: X-10 Home Automation Programming........................................................................80
11.1: X-10 Overview........................................................................................................................80
11.2: HA Units .................................................................................................................................80
11.3: House Code ...........................................................................................................................83
11.4: HA Control..............................................................................................................................83
Chapter Twelve: System Initialization....................................................................................................84
12.1: Initialization ............................................................................................................................84
12.2: Default Program Restore .......................................................................................................84
12.3: Clear User Codes...................................................................................................................84
12.4: Clear Wireless Transmitters...................................................................................................85
12.5: Find Modules..........................................................................................................................85
Appendix A: Menu Structure..................................................................................................................86
Appendix B: Transmitter Installation......................................................................................................93
PIR Sensors (MS845) .....................................................................................................................93
Magnetic Contact (DS831)..............................................................................................................96
Universal Transmitter (US832)........................................................................................................98
Glass break Sensor (GB843) ..........................................................................................................99
Smoke Detector (SD833) ..............................................................................................................102
Keyfobs (PR811/KR814)...............................................................................................................103
Wireless Keypads (WK820/RC840) ..............................................................................................104
-4- © HAIBRAIN

Transmitter Specifications.............................................................................................................106
Appendix C: Event Table .....................................................................................................................107
Appendix D: Zone Types .....................................................................................................................109
Declaration of Conformity ....................................................................................................................111
ProGuard800™ -5-

Chapter One: Introduction
This manual is designed to help you install the ProGuard800 control panel. We strongly
urge you to read through this manual, in its entirety, before beginning the installation
process so that you can best understand all that this security system has to offer. This
manual is not intended for end user use. End users are encouraged to read the user manual
provided with the system. If you have any questions concerning any of the
procedures described in this manual please look at www.Haibrain.com.
1.1: Documentation Conventions
Throughout the manual, we have tried to include all of the operating and programming
functions using a similar structure and order as they appear in the menu. A detailed
explanation of how to navigate the panel’s menu is included in section 4.1: Menu
Navigation. In order to simplify the procedures that appear in the rest of this manual, the
following conventions are used:
This… Means…
Select… Use the arrow keys to scroll through the options and press
3.
From the Event Log Menu,
select Clear Log.
Enter the main menu by pressing 3and entering your user
code. Using the arrow keys, navigate until you reach Event
Log and press 3. Using the arrow keys, navigate until you
reach Clear Log and press 3.
From the Service menu, select
Time/Date, Set Date.
The same as above only this time you are navigating through
three menu levels.
[7012] The shortcut to a specific menu item from the main menu. In
this case, this is the shortcut for Set Date. These appear in
the procedures as an additional aid to menu navigation.
[#5] A shortcut to a specific item in a sub-menu. For example,
[#5] is the shortcut to Bell enable disable in the sub-menu
that is opened once you have selected the sensor you want
to program.
3The symbol on a key that appears on the keypad
5. Interface Test The text that actually appears on the LCD display (bold
italics).
1Important note, please pay attention.
Table 1.1: Documentation Conventions
-6- ©HAIBRAIN

1.2: Specifications
General
Zones: 32 wireless zones (1 transmitter per zone), 1 hardwire zone (Zone 33)
Wireless Keyfobs: 19 (Controlled or Non-controlled)
Wireless Keypads: 4
HK855 Hardwire LCD Keypads: 2 (PROGUARD800-KPD/L), 3 (PROGUARD800-KPD/S)
Repeaters: 4
Smartkeys (future option): 16 (Controlled or Non-controlled)
Wireless Siren: 1 (1-way or 2-way)
User Codes: 32
Arming Methods: Full, Part or Perimeter
Event Log: 256 event capacity, time and date stamped
Communications
Monitoring station Event Reporting Accounts: 3 (8-digit account number)
Vocal Message Accounts: 3
Telephone Numbers: 3 regular, 3 Vocal Message, RP Callback and Service Call
(16-digits each)
Communication Interface Options: PSTN or GSM (optional expansion module required)
Home Automation
Control Medium: Power-line carrier
Protocol: X-10
HA Units: 16 individually addressed
Receiver
Type: Super-heterodyne, fixed frequency
Frequency: 868.35 MHz FM
Data Encryption: SecuriCode™
Electrical
Power Input: 230VAC, 50Hz
Backup Battery Pack: 7.2V/1.5Ah (6 x 1.2V Ni-MH rechargeable cells, size AA)
Fuse Ratings: 63mA/250V (AC protection fuse), 1A/250V (battery protection fuse)
PGM Relay Output Contact Rating: 100mA (max. load)
Built-in Siren: 105dB or 85dB
Tamper Switch: N.C.
Operating Temperature: 0-60°C
1.3: System Overview
The ProGuard800 is a full-featured wireless control panel that is expected to provide a
solution to the needs of most residential installations. This system has been developed
based upon a design concept geared towards easy installation and use. With this in mind,
the user interface is based on a simple, menu-driven model that suits the essential
requirements of both the user and installer alike. You can program the ProGuard800 on-site
using the on-board LCD keypad or off-site via a PC using the up/downloading software.
Monitoring station communication and up/downloading employ either regular PSTN or high-
speed cellular communication. SMS messaging provides an innovative method used for both
monitoring station and Follow-me user monitoring. Additionally, SMS messages can be sent
to the panel enabling the user to send commands to the system from anywhere on the
planet.
ProGuard800™ -7-

The panel’s home automation capabilities provide a wealth of features. The Home
Automation module interfaces with X-10 units over the powerline network and grants the
user appliance control via a number of different media.
The following diagram shows the components that make up the system and the system’s
interaction with external communication networks.
Figure 1.1: System Architecture
-8- ©HAIBRAIN

1.4: Hardware Layout
The aim of this section is to acquaint you with the various circuit boards that make up the
system. Apart from the Main Board, each peripheral module is available as an optional
extra designed for installation inside the plastic housing.
Figure 1.2: System Layout
1. Main Board
2. PSTN dialer module (optional)
3. Home Automation module (optional)
4. Cellular communications module (optional)
5. Backup battery pack
ProGuard800™ -9-

1.4.1: The Main Board
The Main Board is the brain of the system and connects to various peripheral modules
using a number of interface connectors. Additionally, the Main Board includes a
programmable output, a hardwire zone input and a USB port for PC programming.
Figure 1.3: Main Board
1. USB port for connection to PC
2. DIP-switch for flash programming
3. Connector for on-board transmitter
4. Flat-cable interface connector to PSTN module
5. Auxiliary power output (AC Operated:10-15V, Battery Operated: 6-
8V)
6. Programmable relay output (100mA max. load)
7. Hardwire zone (Zone 33)
8. Status LED
9. Interphone module connector
10. Flash programming connector for main board
11. HK855 Hardwire LCD Keypad terminal block
12. Flat-cable interface connector to LCD keypad, built-in speaker,
microphone and siren
13. Front tamper switch
14. Programming keypad connector (optional)
15. Interface connector to Home Automation module
16. AC power terminal block
17. Home Automation module terminal block
18. AC power protection fuse
19. Backup battery protection fuse
20. Flat-cable interface connector to GSM module
21. Backup battery connector
22. Additional backup battery connector
-10- © HAIBRAIN

1.4.2: PSTN Module
The PSTN module provides the system with a standard dialer for communication via the
Public Switched Telephone Network (PSTN).
1Do not use VoIP phone lines for communication to the central monitoring station. In certain
cases the system may not transmit alarm signals successfully over the VoIP network.
Alternative
Telephone
Line Socket
O
p
tion
Figure 1.4: PSTN Module
1. Status LED
2. Flash programming connector
3. Telephone line terminal block (Terminals 1 & 2: Incoming line from
telephone company, Terminals 3 & 4: Outgoing line to telephone)
4. Flat-cable interface connector to Main Board
5. Telephone socket for incoming line from telephone company
6. Telephone socket for outgoing line to telephone
1.4.3: Home Automation Module
The Home Automation module provides the system with an interface to the power-line
network, enabling control over 16 home automation units employing the X-10 protocol.
Figure 1.5: Home Automation Module
1. Interface connector to Main Board
2. Flash programming connector
3. Power-line terminal connections to Main Board (1- Neutral; 2- Live)
ProGuard800™ -11-

1.4.4: Cellular Communications Module
The Cellular Communications module enables the control panel to communicate via
cellular networks. This offers the ability to send or receive SMS messages, perform
up/downloading, implement cellular 2-way voice applications.
Figure 1.6: Cellular Communications Module
1. SIM card holder
2. SIM card release
3. Status LED
4. Flash programming connector
5. Flat-cable interface connector to Main Board
-12- ©HAIBRAIN

Chapter Two: System Installation
The following chapter explains how to install the system and provides guidelines and tips
on how to optimize the installation. It is recommended that you familiarize yourself with
the various circuit boards that make up the system – see 1.4: Hardware Layout.
2.1: Pre-Installation Planning
Before starting the installation procedure, it is worthwhile to draw a rough sketch of the
building and determine the required position for the control panel and each wireless device.
When deciding on the placement for installation, consider the following:
xMount the control panel in a location with easy access to telephone and power
connections.
xIf installing with the GSM Cellular Communications module, the control panel
should be mounted in a position where the GSM signal is strong.
xRefer to the following section in order to choose the optimal location for
wireless devices in relation to the control panel.
2.1.1: Wireless Installation Guidelines
In order to optimize wireless communication, consider the following guidelines:
xWhenever possible, mount the panel centrally in relation to wireless
sensors.
xAvoid installation in close proximity to sources of high noise or radio
frequency interference. For example, metal air conditioner/heater ducts
and circuit breaker boxes.
xMinimize the distance between the panel and transmitters.
xMinimize the number of obstacles between the panel and transmitters.
Figure 2.1: Minimizing Obstacles
xMetal based construction materials, such as steel reinforced concrete
walls, reduce the range of radio transmissions.
Figure 2.2: Considering Construction Materials
ProGuard800™ -13-

xThe reduction of the RF signals’ strength is directly proportional to the
thickness of the obstacle, assuming that the obstacles are of identical
material.
Figure 2.3: Considering Thickness of Obstacles
2.2: Installation Procedure
After unpacking the kit and making certain that you have all the necessary equipment, it
is recommended that you install the system as follows:
STEP 1: Open the housing.
STEP 2: Temporarily power up the system.
STEP 3: Register the transmitters.
STEP 4: Test the chosen mounting location.
STEP 5: Permanently install the control panel and transmitters.
2.2.1: Step 1 – Opening the Housing
To open the housing:
1. Remove the housing screw located
at the bottom of the front cover.
2. Using a screwdriver carefully
press the release tabs as shown
in Figure 2.4.
3. Lift the front cover away from the
back of the housing. You will
notice that the front cover is
attached to the back with
two fastening bands and the
keypad’s flat cable.
Housing
Screw
Figure 2.4: Opening the Housing
2.2.2: Step 2 – Powering Up the System
In order to register and test transmitters, it is necessary to temporarily power up the system
before installing the control panel. At this stage, do not connect the backup battery.
Thread the power cable through the wiring hole on the back cover and connect the cable to
the AC power input on the Main board. For the exact location of the AC power input, see
section 1.4.1: The Main Board. Close the front cover and apply AC power. At this stage,
ignore any trouble conditions that may appear on the LCD display (e.g. Low Battery).
-14- ©HAIBRAIN

2.2.3: Step 3 – Registering Transmitters
For the control panel to recognize a device, its transmitter must be registered. In general
terms, transmitter registration means sending two transmissions from a device when the
control panel is in “Registration” mode.
To register a device:
1. Press 3.
2. Enter your Installer code (the default Installer code is 1111).
3. Enter 91 (Programming, Devices) to enter the Devices menu.
4. Press the menu navigation keys (/), until the type of device you
want to register appears on the LCD display (e.g. Zones or Keypads).
5. Press
3.
6. Press the menu navigation keys (/), until the exact device you
want to register appears on the LCD display (e.g. Zone 3 or Keypad 2).
7. Press
3. If a device has not been registered at the chosen location,
the control panel initiates Registration mode. During Registration
mode, the system waits for two transmissions from the device.
1If a device has already been registered at the required location, the system will not initiate
Registration mode. If the device has already been registered at another location, attempts
to register are ignored by the system.
8. Send two transmissions from the device – refer to each device’s
installation instructions in Appendix B for further details.
9. When Save? is displayed on the control panel’s LCD, press 3. The
display automatically switches to the next option for that device. For
example, pressing 3to confirm Zone registration automatically moves
you to the Zone Type option.
10. Continue entering other parameters for the chosen device.
1Pressing 2returns you to the previous menu level. Press 2when you are in the Main menu
(Menu Level 1) to exit menu mode.
2.2.4: Step 4 – Testing the Chosen Mounting Location
Once all of the transmitters are registered, it is recommended that you test the chosen
mounting locations before permanently mounting the control panel and wireless devices. You
can test the transmitter signal strength using the TX Test feature.
To test transmitter signal strength.
1. Press 3.
2. Enter your Installer code.
3. Enter
7072 (Service, Transmitters, TX Test) to initiate TX Test mode.
4. Activate the transmitter you wish to test; the transmitter’s details appear
on the control panel’s LCD. Additionally, between one and four tones are
sounded to indicate the transmitter’s signal strength. If four tones are
sounded, the transmitter is in the best possible location – see 4.7.7:
Transmitters for further information.
5. After you have tested each transmitter, press 2to exit TX Test mode.
If installing with the GSM Cellular Communications module, test the GSM signal strength
using the system’s RSSI meter.
To test the GSM signal strength:
1. Press 3.
2. Enter your Installer code.
ProGuard800™ -15-

3. Enter 709 (Service, GSM Signal); the signal strength of the cellular
network is displayed – see 4.7.9: GSM Signal Strength for further
information.
2.2.5: Step 5 – Installing the Control Panel and Transmitters
Having chosen and tested the mounting location of the control panel and each
transmitter, you are now ready to permanently install the system.
To permanently install the transmitters, refer to each device’s installation instructions (in
Appendix B of this manual or supplied individually with each product).
To install the control panel:
1. Disconnect AC power from the control panel.
2. Open the housing as explained in section 2.2.1: Step 1 – Opening the
Housing.
3. Remove the backup battery pack. If you want to install the control
panel with back tamper, it is also necessary to disconnect the flat cable
connecting the Main board to the front panel keypad and remove the
Main board. Figure 2.5 shows the control panel with the Main board
and the battery pack removed.
Upper
Mounting
Hole
Upper
Mounting
Hole
Location of
Back Tamper
Screw
Lower
Mounting
Hole
Lower
Mounting
Hole
Figure 2.5: Back Cover (Main Board and Battery Pack removed)
4. Place the control panel in position against the wall and mark the upper
and lower mounting holes. If using the back tamper, also mark the hole
for the back tamper screw.
5. Install wall anchors in the appropriate positions.
6. Thread any required cables through the wiring hole on the back cover
(e.g. AC power and telephone line) and make any necessary wiring
connections.
7. Connect the power cable to the AC power input on the Main board –
see 1.4.1: The Main Board.
8. Connect the telephone line to the Telephone Line terminal block on the PSTN
module – see 1.4.2: PSTN Module.
9. Connect any additional HK855 Hardwire LCD Keypads if required – see 2.4:
Installing HK855 Hardwire LCD Keypads.
-16- ©HAIBRAIN

10. Mount the control panel to the wall using four screws and insert the back tamper
screw if required – see 2.3: Back Tamper.
1The control panel shall be mounted so that it shall withstand a force of at least three times
its own weight.
11. Replace the Main Board and reconnect its peripheral modules.
12. Connect the flat cable connecting the Main board to the front panel keypad and
the replace the front cover’s fastening bands.
13. Apply AC power.
1Always connect AC power before connecting the battery pack. Batteries are supplied
uncharged. When you first connect the battery, it is probable that the system will display a
Low Battery condition. Allow the battery to charge for at least 18 hours before use.
14. Connect the battery pack to the connector on the Main Board.
15. Position the front cover’s top holding hooks onto the back cover and snap the
front cover closed.
16. After installing the control panel, perform the Find Modules function – see 12.5:
Find Modules.
2.3: Back Tamper
The back tamper switch is an optional feature that provides an extra
safeguard in the event that the control panel is removed from the wall. Figure 2.6: Perforated
Back Tamper Release
The back tamper switch is located on the rear side of the control
panel’s Main Board and is constantly depressed by the section of the
back cover shown in Figure 2.6.
For this feature to operate, you must insert a screw into the back tamper mounting hole –
see section 2.2.5: Step 5 – Installing the Control Panel and Transmitters. When the
control panel is removed from the wall, the screw causes the perforated section of the
plastic to break and remain attached to the wall. As a result, the back tamper switch is
released and an alarm is generated.
2.4: Installing HK855 Hardwire LCD Keypads
The system supports HK855 Hardwire LCD Keypads that may be installed up to 300m
from the control panel.
Flash Programming
Connector LCD Contrast
Potentiometer
Terminal
Block
Tamper
Switch
Figure 2.7: HK855 Hardwire LCD Keypad (back cover off)
ProGuard800™ -17-

To install HK855 Hardwire LCD Keypads.
1. Disconnect all power, both AC and battery, from the control panel.
2. Remove the back cover of the keypad. To do so, press the two snaps
(located at the bottom of the keypad) using a small flat-head
screwdriver and carefully pull the back cover away from the front of the
housing.
3. Place the back cover of the keypad in position against the wall and
mark the upper and lower mounting holes.
4. Install wall anchors in the appropriate positions.
5. Thread the cable from the control panel through the wiring hole on the
back cover and attach the back cover to the wall using four screws.
6. Connect the terminal block on the keypad to the appropriate terminal
block on the control panel’s main board as shown in Figure 2.8.
Figure 2.8: Connections for HK855 Hardwire LCD Keypad
7. Reapply power to the control panel.
8. Set the keypad address as follows:
a. Make certain the keypad’s tamper switch is open.
b. On the keypad, press keys 1, 3 and 5
simultaneously.
c. Use the arrow keys (/) to select the keypad
address.
d. Press 3.
9. Position the front cover’s top holding hooks onto the back cover and
snap the front cover closed.
10. After installing hardwire keypads, perform the Find Modules function – see
12.5: Find Modules.
-18- ©HAIBRAIN

Chapter Three: Basic System Operation
3.1: Front Panel Layout
The front panel provides a detailed interface for operating and programming the system.
The following diagram will familiarize you with the various elements on the front panel.
LCD
Display
System
Status
LEDs
Arming
Keys Menu
Navigation
Keys
Alpha-
numeric
Keypad
Figure 3.1: Front Panel
3.2: System Status LEDs
The two LEDs, Armed and Power, provide essential information on the status of the
system.
If the Armed LED is…
±
It means…
Off The system is disarmed.
On The system is armed.
Flashing An alarm has occurred. Alarm indication is cleared the next time
that an arming sequence is initiated or after the relevant event has
been viewed in the event log.
Table 3.1: Armed LED Indication
1Alarm indication is not displayed after a silent panic alarm.
If the Power LED is…
a
It means…
Off Both AC and Battery power are disconnected.
On System Power is OK.
Flashing (slow) Backup battery low or low battery from transmitters.
Flashing (fast) AC loss.
Table 3.2: Power LED Indication
ProGuard800™ -19-

3.3: Front Panel Keypad
The alphanumeric keypad on the front panel enables you to perform various operation
and programming tasks. Apart from the regular functions of a standard alphanumeric
keypad, the keypad offers a number of special functions. These functions are listed in the
following table.
Key Special function
1 Used to enter symbols in descriptor editing.
0 Used to enter symbols in descriptor editing.
2Used to cancel the current selection.
Used to return to the previous menu level.
3Used to enter Menu mode.
Used to select the current menu item.
Used to signify the end of an entered value.
Toggles status in Zone Bypass/Unbypass function.
Used to switch Home Automation units on.
In descriptor editing, used to insert a space before the current character.
In phone number editing, used to enter “T”, “,”, “P”, “+”, “*”, “#”.
In account number editing, used to enter Hexadecimal digits (A-F).
Toggles item descriptors and default names.
In the event log, toggles the time/date stamp.
Toggles AM and PM when setting the time in 12hr format.
Used to switch Home Automation units off.
In descriptor and phone number editing, used to delete the current character.
Used to scroll backwards in the current menu level.
For Global Chime and Message Center features, used to access shortcuts.
+ (Global Chime shortcut)
+ 2(Record Message shortcut)
+ 3(Play Message shortcut)
Used to scroll forwards in the current menu level.
During standby, used to scroll through the list of system trouble conditions.
Table 3.3: Front Panel Keypad Functions
3.4: LCD Display
The LCD display provides you with a detailed interface for operation and programming.
3.4.1: Standby Mode
Standby mode can be defined as the state the
system is in when it is disarmed and not in Menu
mode. In Standby mode, the armed status,
system status or banner are displayed. If system
status is normal, the current time is displayed.
DISARMED
11:22:02
Figure 3.2: Typical Standby Display
-20- ©HAIBRAIN